DLA SMD-5962-88551 REV B-2005 MICROCIRCUIT LINEAR QUAD OR RELAY DRIVER HIGH OUTPUT VOLTAGE AND CURRENT MONOLITHIC SILICON《硅单片高输出电压和电流四方或继电器驱动器线性微电路》.pdf

《DLA SMD-5962-88551 REV B-2005 MICROCIRCUIT LINEAR QUAD OR RELAY DRIVER HIGH OUTPUT VOLTAGE AND CURRENT MONOLITHIC SILICON《硅单片高输出电压和电流四方或继电器驱动器线性微电路》.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-88551 REV B-2005 MICROCIRCUIT LINEAR QUAD OR RELAY DRIVER HIGH OUTPUT VOLTAGE AND CURRENT MONOLITHIC SILICON《硅单片高输出电压和电流四方或继电器驱动器线性微电路》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R237-92. 92-07-01 M. A. Frye B Incorporate rev. A NOR. Update drawing to current requirements. Editorial changes throughout. - drw 05-05-19 Raymond Monnin THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLA

2、CED. REV SHET REV SHET REV STATUS REV B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Joseph A. Kerby DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Ray Monnin COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTME

3、NTS APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, QUAD OR RELAY DRIVER, HIGH OUTPUT VOLTAGE AND AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 88-09-01 CURRENT, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-88551 SHEET 1 OF 7 DSCC FORM 2233 APR 97 5962

4、-E344-05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88551 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describe

5、s device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88551 01 C A Drawing number Device type (see 1.2.1) Case outline(see 1.

6、2.2) Lead finish(see 1.2.3)1.2.1 Device type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 UH 503 Quad OR relay driver, high output voltage and current 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follow

7、s: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-f14 14 Flat pack 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage . 7.0 V dc Input voltage 5.5 V

8、 dc Output off-state voltage . 100 V dc Output on-state sink current 500 mA Storage temperature -65C to +150C Lead temperature (soldering 10 seconds) . +300C Junction temperature (TJ) +150C Thermal resistance, junction-to-case (JC): Cases C and D. See MIL-STD-1835 Thermal resistance, junction-to-amb

9、ient (JA): Case C . 90C/W Case D . 140C/W 1.4 Recommended operating conditions. Supply voltage (VCC) 4.5 V dc to 5.5 V dc Current into any output (on-state) 250 mA maximum Ambient operating temperature range (TA) -55C to +125C Provided by IHSNot for ResaleNo reproduction or networking permitted with

10、out license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88551 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and

11、 handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTM

12、ENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these docu

13、ments are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and t

14、he references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-

15、PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be pro

16、cessed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect

17、form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construc

18、tion, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections and block diagram. The terminal connections and block diagram shall be as specified on figure 1. 3.

19、3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgr

20、oups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages whe

21、re marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, app

22、endix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWIN

23、G SIZE A 5962-88551 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Input current

24、, high IIN(1) Other input = 0 V, VCC= 5.5 V, driven input = 2.4 V 1, 2, 3 All -40 A Other input = 0 V, VCC= 5.5 V, driven input = 5.5 V 1,000 Input current, low IIN(0) Other input = 4.5 V, VCC= 5.5 V, driven input = 0.4 V 1, 2, 3 All -800 A Output reverse current IOFFOther input = 0 V, VOUT= 100 V,

25、driven input = 2.0 V, VCC= 4.5 V 1, 2, 3 All 100 A Output voltage, low VONVCC= 4.5 V, all inputs = 0.8 V, output = 150 mA 1, 3 All 0.5 V 2 0.6 VCC= 4.5 V, all inputs = 0.8 V, output = 250 mA 1, 3 0.7 2 0.8 Supply current, high level ICC(1) TA= +25C, VCC= 5.5 V, all inputs = 5 V, each gate 1 All 7.5

26、mA Supply current, low level ICC(0) TA= +25C, VCC= 5.5 V, all inputs = 0 V, each gate 1 All 26.5 mA Propagation delay, turn-on time tPDON VS= 100 V, VCC= 5.0 V, CL= 15 pF, RL= 670 9, 10, 11 All 500 ns Propagation delay, turn-off time tPDOFF 750 Input voltage, high VIN(1) VCC= 4.5 V 1, 2, 3 All 2.0 V

27、 Input voltage, low VIN(0) 0.8 Diode leakage current IRVCC= 5.0 V, all inputs = 0 V, output = open 1, 2, 3 All 200 A Diode forward voltage VFVCC= 5.0 V, all inputs = 5.0 V, output = 200 mA 1, 2, 3 All 1.75 V Strobe input current, low IIN(0) VCC= 5.5 V, other inputs = 4.5 V, driven input = 0.4 V 1, 2

28、, 3 All -1600 A Strobe input current, high IIN(1) VCC= 5.5 V, other inputs = 0 V, driven input = 2.4 V 1, 2, 3 All 100 A VCC= 5.5 V, other inputs = 0 V, driven input = 5.5 V 1000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT D

29、RAWING SIZE A 5962-88551 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 Cases C and D FIGURE 1. Terminal connections and block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD

30、MICROCIRCUIT DRAWING SIZE A 5962-88551 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL

31、-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate o

32、f conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent,

33、 and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in

34、accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) T

35、est condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicabl

36、e, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4

37、.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgrou

38、ps 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test ci

39、rcuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specifi

40、ed in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88551 DEFENSE SUPPL

41、Y CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - - - Final electrical test pa

42、rameters (method 5004) 1*, 2, 3, 9 Group A test requirements (method 5005) 1, 2, 3, 9, 10*, 11* Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. * Subgroups 10 and 11, if not tested, shall be guaranteed to the specified limits in table I. 5. PACKAGING

43、 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistic

44、s purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individu

45、al documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system application requires configuration control and the applicable SMD. DSCC will maint

46、ain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columb

47、us, Ohio 43218-3990, or telephone (614) 692-0547. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. Prov

48、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 05-05-19 Approved sources of supply for SMD 5962-88551 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-385

49、35 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the ne