DLA SMD-5962-87003 REV B-2010 MICROCIRCUIT LINEAR TONE DECODER PHASE LOCKED LOOP MONOLITHIC SILICON.pdf

《DLA SMD-5962-87003 REV B-2010 MICROCIRCUIT LINEAR TONE DECODER PHASE LOCKED LOOP MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-87003 REV B-2010 MICROCIRCUIT LINEAR TONE DECODER PHASE LOCKED LOOP MONOLITHIC SILICON.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add the words, “CURRENT CAGE CODE 67268” to the first sheet. Changes in accordance with NOR 5962-R178-96. 96-07-10 M. A. FRYE B Update boilerplate paragraphs to current MIL-PRF-38535 requirements. Redrawn. - ro 10-01-25 C. SAFFLE CURRENT CAGE COD

2、E 67268 THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY DONALD R. OSBORNE DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWIN

3、G THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY D. A. DiCENZO APPROVED BY N. A. HAUCK MICROCIRCUIT, LINEAR, TONE DECODER/PHASE LOCKED LOOP, MONOLITHIC SILICON DRAWING APPROVAL DATE 87-02-24 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 14933 5

4、962-87003 SHEET 1 OF 9 DSCC FORM 2233 APR 97 5962-E136-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87003 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234

5、 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87003 01 C A Drawing n

6、umber Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 567 Tone and frequency decoder 1.2.2 Case outline(s). The case outline(s) are as designated in

7、 MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage (VC

8、C) +10 V Positive voltage at input (+VIN) . VCC+ 0.5 V dc Negative voltage at input (-VIN) -10 V dc Output voltage (collector of output transistor) . 15 V dc Maximum power dissipation (PD) . 300 mW 1/ Storage temperature range . -65C to +150C Lead temperature (soldering, 60 seconds) +300C Junction t

9、emperature (TJ) . +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 1.4 Recommended operating conditions. Operating voltage range (V+) 4.75 V dc to 9 V dc Operating voltage 5.0 V dc Ambient operating temperature range (TA) . -55C to +125C Provided by IHSNot for ResaleNo reproduction

10、 or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87003 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following

11、specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, Gener

12、al Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Dr

13、awings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and

14、the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL

15、-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be pr

16、ocessed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect

17、 form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, constru

18、ction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Logic diagram. The logic diagra

19、m shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electric

20、al test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87003 DEFENSE SUPPLY CENTER

21、COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking

22、of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. Th

23、e compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved sou

24、rce of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conforma

25、nce. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review

26、. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted wit

27、hout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87003 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA+125C Group A subgroupsDevice type Limits U

28、nit unless otherwise specified Min Max Input resistance 1/ RINVCC= 5.0 V 1,2,3 01 15 25 k Smallest detectable input voltage VINVOUT= Low 1 01 25 mVrms2,3 50 Largest no output input voltage VINVOUT= High 1 01 7 mVrms2,3 5 Output leakage current ICEXVOUT= 15 V 1 01 25 A 2,3 50Output low voltage VOLIOU

29、T= 30 mA 1,2,3 01 0.4 V IOUT= 100 mA 1 1.0 2,3 1.2Operating supply voltage range VCC1,2,3 01 4.75 9.0 V Supply current quiescent ICCRL= 20 k, VCC= 5.0 V 1 01 8.0 mA 2,3 9.8Supply current activated ICCRL= 20 k, VCC= 5.0 V 1 01 13.0 mA 2,3 14.5Center frequency distribution fOVCC= 5.0 V, 2/ fO= 100 kHz

30、 = 1.1 / R1C14,5,6 01 -10 +10 % Center frequency shift with supply voltage fO/ VCCVCC= 5 V to 8 V, TA= +25C 4 01 1 %/V Largest detection bandwidth DBW VCC= 5.0 V, 4 01 12 16 % of fOfO= 100 kHz = 1.1 / R1C15,6 7 19 Largest detection bandwidth skew DBW skew VCC= 5.0 V 4,5,6 01 4 % of fO1/ These parame

31、ters are guaranteed but not tested. 2/ Frequency determining resistor R1should be between 2 k and 20 k. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87003 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 4321

32、8-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87003 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LE

33、VEL B SHEET 7 DSCC FORM 2234 APR 97 FIGURE 2. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87003 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2

34、234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspec

35、tion. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon r

36、equest. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except in

37、terim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criter

38、ia shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 7, 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Ste

39、ady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify

40、 the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networ

41、king permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87003 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-

42、STD-883, method 5005, table I) Interim electrical parameters (method 5004) - Final electrical test parameters (method 5004) 1*, 2, 3, 4 Group A test requirements (method 5005) 1, 2, 3, 4, 5, 6 Groups C and D end-point electrical parameters (method 5005) 1, 4 * PDA applies to subgroup 1. 5. PACKAGING

43、 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistic

44、s purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individu

45、al documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system application requires configuration control and the applicable SMD. DSCC will maint

46、ain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columb

47、us, Ohio 43218-3990, or telephone (614) 692-0547. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. Prov

48、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 10-01-25 Approved sources of supply for SMD 5962-87003 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by