DLA SMD-5962-12228-2012 MICROCIRCUIT LINEAR OPERATIONAL AMPLIFIER QUAD 40 V LOW POWER MONOLITHIC SILICON.pdf

《DLA SMD-5962-12228-2012 MICROCIRCUIT LINEAR OPERATIONAL AMPLIFIER QUAD 40 V LOW POWER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-12228-2012 MICROCIRCUIT LINEAR OPERATIONAL AMPLIFIER QUAD 40 V LOW POWER MONOLITHIC SILICON.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHEET REV SHEET 15 16 17 18 REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS D

2、RAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY CHARLES F. SAFFLE MICROCIRCUIT, LINEAR, OPERATIONAL AMPLIFIER, QUAD, 40 V, LOW POWER, MONOLITHIC SILICON DRAWING APPROVAL DATE 12-09-04 AMSC N/A REVISION LEVEL SIZE A CAGE

3、CODE 67268 5962-12228 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E390-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-12228 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 2 DSCC FORM 22

4、34 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When

5、available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 F 12228 01 V X C Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Le

6、ad finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identif

7、y the circuit function as follows: Device type Generic number Circuit function 01 ISL70417SEH Quad, 40 V, low power operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements

8、 documentation Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X CDFP3-F14 14 Flat pack 1.2.5 Lead finish. The lead finish is as specifie

9、d in MIL-PRF-38535 for device classes Q and V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-12228 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute m

10、aximum ratings. 1/ Maximum supply voltage . 42 V 2/ Maximum differential Input current 20 mA Maximum differential input voltage 20 V Minimum/maximum input voltage -VS 0.5 V to +VS+ 0.5 V Maximum/minimum input current for input voltage +VSor -VS. 20 mA Output short circuit duration (1 output at a tim

11、e) . Indefinite Power dissipation (PD) : At +25C 1.19 W At +125C 238 mW Maximum junction temperature (TJ) +150C Lead temperature (soldering, 10 seconds) +300C Storage temperature range -65C to +150C Thermal resistance, junction-to-ambient (JA) . 105C/W 3/ Thermal resistance, junction-to-case (JC) 15

12、C/W 4/ 1.4 Recommended operating conditions. Supply voltage . 4.5 V to 30 V Split supply voltage (-VS, +VS) . 2.25 V to 15 V Ambient operating temperature range (TA) . -55C to +125C 1.5 Radiation features. Maximum total dose available (dose rate = 50 300 rads(Si)/s) . 300 krads(Si) 5/ Maximum total

13、dose available (dose rate 0.01 rads(Si)/s) . 50 krad(Si) 5/ Single event phenomenon (SEP) features: No Single event latchup (SEL) occurs at effective LET (see 4.4.4.2) 73.9 MeV/mg/cm26/ No Single event burnout (SEB) occur at effective LET (see 4.4.4.2) . 73.9 MeV/mg/cm26/ _ 1/ Stresses above the abs

14、olute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ For applications that operate in a heavy ion environment, the 42 V absolute maximum rating decreases to 40 V. 3/ JAis measured with the component

15、 mounted on a low effective thermal conductivity test board in free air. 4/ For JC, the case temperature location is the center of the exposed metal pad on the package underside. 5/ The device type 01 radiation end point limits for the noted parameters are guaranteed only for the conditions as speci

16、fied in MIL-STD-883, method 1019, condition A to a maximum total dose of 300 krads(Si), and condition D to a maximum total dose of 50 krads(Si). 6/ Limits are characterized at initial qualification and after any design or process changes which may affect the SEP characteristics but are not productio

17、n tested unless specified by the customer through the purchase order or contract. For more information on SEE test results customers are requested to contact manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING

18、SIZE A 5962-12228 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified her

19、ein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microc

20、ircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ o

21、r from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are the issue

22、s of the documents cited in the solicitation or contract. ASTM INTERNATIONAL (ASTM) ASTM F1192 - Standard Guide for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion Irradiation of semiconductor Devices. (Copies of these documents are available online at http:/www.astm.org or from

23、 ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA, 19428-2959). 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersede

24、s applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Manage

25、ment (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 3.1.1 Microcircuit die. For the requirements of microcircuit die, see appendix A to this document. 3.2 Design, construction, and physical dimensions. The design, construction, and physica

26、l dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Radiation exposure circuit. The radi

27、ation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, t

28、he electrical performance characteristics and postirradiation parameter limits are as specified in table IA and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electri

29、cal tests for each subgroup are defined in table IA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-12228 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 5 DSCC FORM 2234 APR 97 TABLE IA

30、. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ -55C TA +125C Group A subgroups Device type Limits Unit VS= 15 V unless otherwise specified Min Max Offset voltage VOS 1 01 75 V 2,3 110 M,D,P,L,R,F 1 110 Offset voltage drift TCVOS2,3 01 1 V/C Input bias current IIB1 01 -1 +1 nA

31、 2,3 -5 +5 M,D,P,L,R,F 1 -5 +5 Input bias current temperature coefficient TCIIB2,3 01 -5 +5 pA/C Input offset current IOS1 01 -1.5 1.5 nA 2,3 -3 3 M,D,P,L,R,F 1 -3 3 Input offset current temperature coefficient TCIOS2,3 01 -3 +3 pA/C Input voltage range VCM Guaranteed by CMRR 1,2,3 01 -13 13 V Commo

32、n mode rejection ratio CMRR VCM= -13 V to +13 V 1,2,3 01 120 dB Power supply rejection ratio PSRR VS= 2.25 V to 20 V 1,2,3 01 120 dB Open loop gain AOLVO= -13 V to +13 V, RL= 10 k to ground 1,2,3 01 3000 V/mV Output voltage high VOHRL= 10 k to ground 1 01 13.5 V 2,3 13.2 M,D,P,L,R,F 1 13.2 RL= 2 k t

33、o ground 1 13.3 2,3 13.0 M,D,P,L,R,F 1 13.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-12228 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 6 DSCC FOR

34、M 2234 APR 97 TABLE IA. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA +125C Group A subgroups Device type Limits Unit VS= 15 V unless otherwise specified Min Max Output voltage low VOLRL= 10 k to ground 1 01 -13.5 V 2,3 -13.2 M,D,P,L,R,F 1 -13.2 RL= 2 k to gr

35、ound 1 -13.3 2,3 -13.0 M,D,P,L,R,F 1 -13.0 Supply current/amplifier IS1 01 0.53 mA 2,3 0.68 M,D,P,L,R,F 1 0.68 Supply voltage range VSUPPLYGuaranteed by PSRR 1,2,3 01 2.25 20 V Transient response section Slew rate SR AV= 11 , RL= 2 k, 4 01 0.3 V/s VO= 4 VPP5,6 0.2 M,D,P,L,R,F 4 0.2 Small signal rise

36、 time, 10% to 90% of VOUTtrAV= -1, VOUT= 50 mVPP, RL= 10 k to VCM9 01 450 ns 10,11 625 M,D,P,L,R,F 9 625 Small signal fall time, 90% to 10% of VOUTtfAV= -1, VOUT= 50 mVPP, RL= 10 k to VCM9 01 600 ns 10,11 700 M,D,P,L,R,F 9 700 Positive overshoot +OS AV= 1, VOUT= 10 VPP, Rf= 0 , RL= 2 k to VCM4,5,6 0

37、1 33 % Negative overshoot -OS AV= 1, VOUT= 10 VPP, Rf= 0 , RL= 2 k to VCM4,5,6 01 33 % See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-12228 DLA LAND AND MARITIME COLUMBUS, OHIO

38、 43218-3990 REVISION LEVEL SHEET 7 DSCC FORM 2234 APR 97 TABLE IA. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA +125C Group A subgroups Device type Limits Unit VS= 5 V unless otherwise specified Min Max Offset voltage VOS 1 01 150 V 2,3 250 M,D,P,L,R,F 1 250

39、 Offset voltage drift TCVOS2,3 01 1 V/C Input bias current IIB1 01 -1 +1 nA 2,3 -5 +5 M,D,P,L,R,F 1 -5 +5 Input bias current temperature coefficient TCIIB2,3 01 -5 +5 pA/C Input offset current IOS1 01 -1.5 1.5 nA 2,3 -3 3 M,D,P,L,R,F 1 -3 3 Input offset current temperature coefficient TCIOS2,3 01 -3

40、 +3 pA/C Input voltage range VCM Guaranteed by CMRR 1,2,3 01 -3 3 V Common mode rejection ratio CMRR VCM= -3 V to +3 V 1,2,3 01 120 dB Power supply rejection ratio PSRR VS= 2.25 V to 5 V 1,2,3 01 120 dB Open loop gain AOLVO= -3 V to +3 V, RL= 10 k to ground 1,2,3 01 3000 V/mV Output voltage high VOH

41、RL= 10 k to ground 1 01 3.5 V 2,3 3.2 M,D,P,L,R,F 1 3.2 RL= 2 k to ground 1 3.3 2,3 3.0 M,D,P,L,R,F 1 3.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-12228 DLA LAND AND MARI

42、TIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 8 DSCC FORM 2234 APR 97 TABLE IA. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA +125C Group A subgroups Device type Limits Unit VS= 5 V unless otherwise specified Min Max Output voltage low VOLRL= 10 k to gr

43、ound 1 01 -3.5 V 2,3 -3.2 M,D,P,L,R,F 1 -3.2 RL= 2 k to ground 1 -3.3 2,3 -3.0 M,D,P,L,R,F 1 -3.0 Supply current/amplifier IS1 01 0.53 mA 2,3 0.68 M,D,P,L,R,F 1 0.68 1/ Unless otherwise specified, VCM= 0 V, VO= 0 V. 2/ RHA devices supplied to this drawing meet levels L, R, and F of irradiation for c

44、ondition A and levels P and L for condition D. However, devices are only tested at the F level in accordance with MIL-STD-883, method 1019, condition A and the L level in accordance with MIL-STD-883, method 1019, condition D (see 1.5 herein). When performing post irradiation electrical measurements

45、for any RHA level, TA= +25C (see 1.5 herein). 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the opt

46、ion of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “

47、QML“ or “Q“ as required in MIL-PRF-38535. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). The certificate of compliance submitted t

48、o DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for R