DLA SMD-5962-06251 REV D-2010 MICROCIRCUIT HYBRID PULSE WIDTH MODULATOR CONTROLLER HIGH SPEED.pdf

《DLA SMD-5962-06251 REV D-2010 MICROCIRCUIT HYBRID PULSE WIDTH MODULATOR CONTROLLER HIGH SPEED.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-06251 REV D-2010 MICROCIRCUIT HYBRID PULSE WIDTH MODULATOR CONTROLLER HIGH SPEED.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added device type 02. Added case outline Y. Made changes throughout table I. -sld 08-03-07 Robert M. Heber B Paragraph 1.4; Changed the quiesent current for device type 02 from 10.5 mA to 7.1 mA. Made changes throughout table I. Figure 1; changed

2、 dimension A from .100 to .110 inches and 2.54 mm to 2.79 mm. Made correction to figure 3;Tuth table, deleted the last three lines, which are duplicates. -sld 08-08-11 Robert M. Heber C Paragraph 1.3, added digital inputs limit. Table I under oscillator characterisitcs for the initial accuracy range

3、 for device type 02 change the min and max from 190 and 230 kHz to 201 and 217 kHz. For the frequency stability test for device type 02 change the max limit from 2.5 % to 3.8 %. Added note 2 to figure 1 for case outline X and Y. Added note 3 to bulletin page. -sld 10-05-05 Charles F. Saffle D Table

4、I; under the Auxiliary amp characteristics change the test name “Output offset voltage“ to “Input offset voltage“. Figure 1; corrected case outline Y dimensions. Updated drawing paragraphs. -sld 10-11-09 Charles F. Saffle REV SHEET REV D D D D SHEET 15 16 17 18 REV STATUS REV D D D D D D D D D D D D

5、 D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve Duncan DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil/ THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin MICROCIR

6、CUIT, HYBRID, PULSE WIDTH MODULATOR CONTROLLER, HIGH SPEED AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 06-10-11 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-06251 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E475-10 Provided by IHSNot for ResaleNo reproduction or networking

7、permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06251 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38

8、534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 06251 01 K X X

9、 Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RH

10、A levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 PWM5031 Pulse Width Modulator Contoller, High Speed 02 PWM5032, P

11、WM5034 Pulse Width Modulator Contoller, High Speed 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H

12、, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use

13、in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufactu

14、rer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition docu

15、ment; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperat

16、ure range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06251 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are a

17、s designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 24 Flat package Y See figure 1 24 Flat package (straight leads) 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply

18、 voltage (VCC) +7.0 V dc DRVP supply voltage: Device type 01 +7.0 V dc Device type 02 +14.0 V dc Power dissipation (PD) TA= +25C 500 mW Junction temperature . +135C Steady state output current 50 mA Peak output current (internally limited). 1.0 A Analog input voltage range pins 5, 6, 13, and 14 . VE

19、E-0.5 V to VCC+0.5 V Digital inputs -0.3 V to VCC+ 0.3 V Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +300C 1.4 Recommended operating conditions. Supply voltage range (VCC) . +4.5 V dc to +5.5 V dc Output drive voltage: Device type 01 +5.0 V maximum Device type 02

20、 +12.0 V maximum Quiescent current: Device type 01 +5.8 mA maximum Device type 02 +7.1 mA maximum Thermal resistance (TJC) . 6.0C/W Output duty cycle maximum: 50% pin, pin 2 = logic 0 . 97% at 100% duty cycle 50% pin, pin 2 = logic 1 . 50% at 50% duty cycle Sleep mode . 20 A maximum Case operating t

21、emperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those ci

22、ted in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. _ 1/ Stre

23、sses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING S

24、IZE A 5962-06251 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at htt

25、ps:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes pr

26、ecedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. C

27、ompliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the

28、performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, co

29、nstruction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The t

30、ruth table(s) shall be as specified on figure 3. 3.2.4 Block diagram(s). The block diagram(s) shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over

31、the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with M

32、IL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electri

33、cal test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under documen

34、t revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (o

35、riginal copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits

36、delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as

37、 described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06251 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characte

38、ristics. Test Symbol Conditions 1/ -55C TA +125C +4.5 V VCC +5.5 V unless otherwise specified Group A subgroups Device type Limits UnitMin Max Reference characteristics Reference voltage IO= -1 mA, TA= +25C 1 01,02 3.00 3.10 V Line regulation 1,2,3 01,02 0.12 % Load regulation 2/ 0 I/O 3 mA 1,2,3 01

39、,02 0.075 % Thermal regulation 1,2,3 01,02 1.6 % Output short circuit 2/ 1,2,3 01,02 -40 mA Oscillator characteristics Initial accuracy range 1,2,3 01 208.5 219 KHz 02 201 217 Frequency range 2/ 1,2,3 01,02 20 1,000 KHz Frequency stability (part to part) 2/ 1,2,3 01 2.5 % 02 3.8 Temperature stabilit

40、y 2/ TMIN TA TMAX 1,2,3 01,02 1 % RSET range 2/ 1,2,3 01,02 50 K CSET range 2/ 1,2,3 01,02 600 pF Error amp characteristics Input offset voltage 2/ 1,2,3 01,02 3.3 mV Input common mode voltage range 2/ 1,2,3 01,02 VEE+0.2 VCC -0.2 V Input bias current 2/ 1,2,3 01,02 -1.0 A See footnotes at end of ta

41、ble. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06251 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Cont

42、inued. Test Symbol Conditions 1/ -55C TA +125C +4.5 V VCC +5.5 V unless otherwise specified Group A subgroups Device type Limits Unit Min Max Error amp characteristics - Continued Open loop voltage gain 2/ AVOL 1,2,3 01,02 100 dB Unity gain bandwidth 2/ 1,2,3 01,02 1.0 MHz Power supply rejection 2/

43、ratio PSRR 1,2,3 01,02 60 dB Output sink current 2/ VFB= 3.0 V, VSOFT= 1.1 V 1,2,3 01,02 +10 mA Output source current 2/ VFB= 2.0 V, VSOFT= 5 V 1,2,3 01,02 -28 mA VOUThigh (limited by 2/ VSOFT) VFB= 2.0 V, RL= 15K to GND 1,2,3 01,02 VSOFT- 0.2 V VOUTlow 2/ VFB= 3.0 V, RL= 15K to +5 V 1,2,3 01,02 VEE

44、+0.2 V Gain (VCOMP/VISENSE) 2/ 1,2,3 01,02 2.85 3.15 V Current sense characteristics Input offset voltage 2/ 1,2,3 01,02 3.3 mV Common mode input 2/ 3/ voltage VSOFT= +5 V 1,2,3 01,02 1.0 V Input bias current 2/ 1,2,3 01,02 1.0 A ISENSEto output delay 2/ 9,10,11 01,02 100 ns Output characteristics O

45、utput low level ISINK= 1.0 mA, DRVP = +5 V 1,2,3 01 0.1 V ISINK= 50 mA, DRVP = +5 V 01 .6 V Output high level ISOURCE= 1.0 mA, DRVP = +5 V 1,2,3 01 4.9 V ISOURCE= 50 mA, DRVP = +5 V 01 4.6 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without l

46、icense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06251 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA+125C +4.5 V VCC +5.5 V unless otherwise sp

47、ecified Group A subgroups Device type Limits Unit Min Max Output characteristics - Continued Output low level ISINK= 1.0 mA, DRVP = +12 V 1,2,3 02 0.1 V ISINK= 50 mA, DRVP = +12 V 02 .6 Output high level ISOURCE= 1.0 mA, DRVP = +12 V 1,2,3 02 11.9 V ISOURCE= 50 mA, DRVP = +12 V 02 11.4 V Peak output

48、 current 2/ 1,2,3 01,02 1 A Steady state output current DRVP = +5 V, VOUT= 4.25 V 1,2,3 01,02 50 mA Rise time 2/ tR TA= +25C, CL= 20 pF, DRVP = +5 V 9 01,02 18 ns Fall time 2/ tF TA= +25C, CL= 20 pF, DRVP = +5 V 9 01,02 28 ns Enable output off delay 2/ 9 01,02 100 ns Sleep output off delay 2/ 9 01,02 100 ns Under voltage output off delay 2/ 9 01,02 100 ns Auxiliary amp characteristics Input offset volt