DLA MS51535 REV C-2003 TERMINAL LUG SOLDER TYPE COPPER STAMPING TWO HOLE 30 DEG 《焊料型30 DEG 2孔铜冲压片终端接线片》.pdf

《DLA MS51535 REV C-2003 TERMINAL LUG SOLDER TYPE COPPER STAMPING TWO HOLE 30 DEG 《焊料型30 DEG 2孔铜冲压片终端接线片》.pdf》由会员分享，可在线阅读，更多相关《DLA MS51535 REV C-2003 TERMINAL LUG SOLDER TYPE COPPER STAMPING TWO HOLE 30 DEG 《焊料型30 DEG 2孔铜冲压片终端接线片》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5940 INCH-POUND MS51535C 15 December 2003 SUPERSEDING MS51535B 19 August 1986 DETAIL SPECIFICATION SHEET TERMINAL, LUG, SOLDER TYPE, COPPER STAMPING, TWO HOLE, 30 Inactive for new design after 27 October 1998. This specification sheet is approved for use by all departments and agencies

2、 of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet MIL-DTL-15659. .125B.094View at “X“.018 .003ED30“X“CAAC.156FIGURE 1. Terminal dimensions. Optional configuration - see note 5 Provided by IHSNot for ResaleNo reproduct

3、ion or networking permitted without license from IHS-,-,-MS51535C 2 TABLE I. Dash numbers and dimensions. A Dash no. AWG1wire size nominal Stud size Min. Max. B C D E 1 2 0.090 0.096 2 4 0.115 0.127 3 6 0.141 0.153 4 8 0.167 0.179 5 10 0.193 0.205 0.312 0.331 0.406 6 12 0.250 0.253 0.257 0.094 0.375

4、 0.343 0.469 1American Wire Gauge. REQUIREMENTS: 1. Material: Electrolytic copper strip or sheet alloy C11000, temper O60 in accordance with ASTM B 152/B152M (DoD adopted). 2. Finish: Tinned; electrodeposited over entire surface in accordance with ASTM B 545 (DoD adopted). Minimum thickness 0.0005 i

5、nches all over. NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is 0.015. 3. Remove all burrs. 4. Referenced documents of issue in effect on date of invitation for bids shall apply. 5. Dash number 6 shall conform to the optional configuration shown in figure 1. 6. In the

6、 event of a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. 7. The part or identifying number (PIN) consists of the letters MS, the specification sheet number, and a dash number taken from table I. MS 51535 - 3 Dash number

7、Specification sheet number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS51535C 3 CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Army - AV Navy - AS Air Force - 11 DLA - GS2 (Project 5940-1442) Review Activities: Army - MI Navy - MC Air Force - 99 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-