DLA MS500040 REV K-2011 TRANSMITTER LIQUID QUANTITY FLOAT TYPE ENGINE FUEL.pdf

《DLA MS500040 REV K-2011 TRANSMITTER LIQUID QUANTITY FLOAT TYPE ENGINE FUEL.pdf》由会员分享，可在线阅读，更多相关《DLA MS500040 REV K-2011 TRANSMITTER LIQUID QUANTITY FLOAT TYPE ENGINE FUEL.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 6680 INCH-POUND MS500040K 17 November 2011 SUPERSEDING MS500040J 1 March 1991 DETAIL SPECIFICATION SHEET TRANSMITTER, LIQUID QUANTITY, FLOAT TYPE, ENGINE FUEL Inactive for new design after 28 September 1993. This specification is approved for use by all Departments and Agencies of the D

2、epartment of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-10986, “Indicators and Transmitters: Liquid, Temperature and Pressure“. INTENDED USE: 1. An indicator (dashboard unit) and a transmitter (sending unit), when connec

3、ted by a single conductor cable (not supplied) and properly grounded, comprise a liquid quantity gauge. This device is used on military motor vehicles and other internal combustion applications to inform the operator of the level of fuel in the supply tank or tanks. REQUIREMENTS: 1. Material: Materi

4、al shall be in accordance with unit 2, type I, class 1, of MIL-DTL-10986. 2. Finish: Finish shall be in accordance with unit 2, type I, class 1, of MIL-DTL-10986. 3. Design: Design shall be in accordance with unit 2, type I, class 1, of MIL-DTL-10986. Provided by IHSNot for ResaleNo reproduction or

5、networking permitted without license from IHS-,-,-MS500040K 2 NOTES: 1. The part or identifying number to be used for the fuel gauge transmitters acquired to this specification is created as follows: MS 500040 - XX Example: MS500040-10 Dash number (see table I) Specification number MS Prefix TABLE I

6、. Fuel quantity transmitters dash numbers. Dash number Former part number Dimensions Float position Float type A Max (inch) B Min (inch) C (inch) R Max (inch) -1 10872707 7.23 0.13 3.96 3.48 3.93 I Regular -2 8376496 7526038 7.67 0.39 3.96 3.48 4.15 I Regular -3 8376495 10.28 0.47 5.42 5.11 5.51 II

7、Regular -4 10942801 11.94 0.47 5.50 5.20 8.50 II Regular -5 7034597 15.56 0.29 8.21 7.90 9.32 I Regular -6 8376491 16.90 0.19 8.21 7.90 10.53 I Regular -7 10921745 17.15 2.35 9.77 9.71 9.03 II Regular -8 7064625 33.50 1.40 14.79 14.49 21.07 I Long -9 8737838 14.59 0.53 7.40 7.00 8.67 I Regular -10 1

8、2332788 11.65 3.19 7.47 7.41 4.47 I Regular 2. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. 3. Unless otherwise specified, issues of referenced documents are those in effect at the time of solicitation. Prov

9、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS500040K 3 4. When tested in accordance with MIL-DTL-10986, resistance calibration measurements shall be 0.00 to 0.05 ohms at the “EMPTY“ position, and 29.50 to 31.50 ohms at the “FULL“ position, (see figu

10、re 1 and table I). 5. Any portion of the assembly that is below the mounting plane (see figure 1) shall pass through an opening of 1.562 inches in diameter. 6. When testing on the applicable fuel tank, a fuel reserve of 10 percent of the applicable fuel tank capacity shall remain when the float reac

11、hes the “EMPTY“ position (see figure 1) with fuel tank level declining. 7. The float lever fulcrum located by dimension C shall be established in line with the 50 percent fuel level reference (see figure 1 and table I) when testing on the applicable fuel tank. 8. The MS part number and manufacturers

12、 identification shall be marked on the body of the transmitter in accordance with MIL-STD-130, “Identification Marking of U.S. Military Property“. 9. The transmitter shall have a steady, continuous output for all float positions and shall track linearly with the float position. 10. Unless otherwise

13、specified, all steel parts except stainless steel shall be zinc plated in accordance with type II, service condition I, of ASTM B633, “Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel“, in accordance with MIL-DTL-10986. 11. The material used for the float shall be brass

14、, non-leaded sheet or strip copper alloy UNS number C26000 or C26800, annealed temper, in accordance with ASTM B36/B36M, “Standard Specification for Brass Plate, Sheet, Strip, and Rolled Bar“. 12. The use of recycled materials that meet the requirements of the applicable material specifications and

15、that do not jeopardize the intended use of the item is strongly encouraged. 13. For the associated indicator (fuel gauge), see MS24544, “Indicator, Liquid Quantity: 24 Volt DC, Engine Fuel“. 14. This standard is not intended to limit construction to features other than the dimensions, notations, and

16、 references contained within. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS500040K 4 NOTES: 1. All dimensions are in inches. 2. Unless otherwise specified, tolerances 0.015. FIGURE 1. Fuel quantity transmitters. Provided by IHSNot for ResaleNo r

17、eproduction or networking permitted without license from IHS-,-,-MS500040K 5 CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Army - AT DLA - GS DLA -

18、 GS8 (Project 6680-2011-002) Review Activity: Army - CR4 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-