DLA MS39207 REV G-2012 ELBOWS TUBE - SAFETY SLEEVE COMPRESSION TYPE 90 DEGREE.pdf

《DLA MS39207 REV G-2012 ELBOWS TUBE - SAFETY SLEEVE COMPRESSION TYPE 90 DEGREE.pdf》由会员分享，可在线阅读，更多相关《DLA MS39207 REV G-2012 ELBOWS TUBE - SAFETY SLEEVE COMPRESSION TYPE 90 DEGREE.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 4730 MS39207G 30 August 2012 SUPERSEDING MS39207F 29 March 2005 DETAIL SPECIFICATION SHEET ELBOWS, TUBE - SAFETY SLEEVE COMPRESSION TYPE, 90 DEGREE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the pro

2、duct described herein shall consist of this specification sheet. FIGURE 1. Elbows, tube-safety sleeve compression type, 90 degree. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39207G 2 Dash number. Tube O.D. B C Thread Length (mm) D (

3、mm) E (mm) F (mm) G (mm) L (mm) M (mm) 1 1/8 5/16- 24UNF-2A 9/32 (7.14) 3/32 (2.38) .135 (3.43) .139 (3.53) 13/64 (5.16) 1/8 (3.18) 21/32 (16.67) 31/32 (34.61) 2 3/16 3/8- 24UNF-2A 9/32 (7.14) 1/8 (3.18) .196 (4.98) .200 (5.08) 1/4 (6.35) 5/32 (3.97) 21/32 (16.67) 31/32 (34.61) 3 1/4 1/2- 20UNF-2A 2

4、5/64 (3.92) 13/64 (5.16) .261 (6.63) .265 (6.73) 19/64 (7.54) 13/64 (5.16) 3/4 (19.05) 1 5/32 (39.37) 4 5/16 9/16- 18UNF-2A 25/64 (3.92) 13/64 (5.16) .324 (8.23) .328 (8.33) 19/64 (7.54) 13/64 (5.16) 13/16 (20.64) 1 3/16 (30.16) 5 3/8 5/8- 18UNF-2A 7/16 (11.11) 9/32 (7.14) .386 (9.80) .390 (9.91) 19

5、/64 (7.54) 13/64 (5.16) 15/16 (23.81) 1 3/8 (34.93) 6 1/2 3/4- 16UNF-2A 7/16 (11.11) 27/64 (10.71) .514 (13.06) .518 (13.16) 5/16 (7.94) 13/64 (5.16) 1 1/8 (28.58) 1 21/32 (42.07) 7 5/8 15/16- 16UN-2A 15/32 (11.91) 1/2 (12.70) .641 (16.28) .645 (16.38) 11/32 (8.73) 15/64 (5.95) 1 5/16 (33.34) 1 27/3

6、2 (46.83) 8 3/4 1 1/16- 16UN-2A 15/32 (11.91) 21/32 (16.67) .766 (19.46) .770 (19.56) 11/32 (8.73) 13/64 (5.16) 1 1/2 (38.10) 2 3/32 (53.18) 9 7/8 1 3/16- 16UN-2A 15/32 (11.91) 23/32 (18.26) .891 (22.63) .895 (22.73) 11/32 (8.73) 13/64 (5.16) 1 3/4 (44.45) 2 11/32 (59.53) 10 1 1 5/16- 16UN-2A 5/32 (

7、3.97) 7/8 (22.23) 1.016 (25.81) 1.020 (25.91) 13/32 (10.32) 13/64 (5.16) 1 3/4 (44.45) 2 11/32 (59.53) 11 1 1/4 1 5/8- 16UN-2A 35/64 (13.89) 1 3/32 (3.38) 1.270 (32.26) 1.274 (32.36) 13/32 (10.32) 13/64 (5.16) 2 1/4 (57.15) 2 7/8 (73.03) 12 1 1/2 1 7/8- 16UN-2A 9/16 (14.29) 1 11/32 (9.73) 1.520 (38.

8、61) 1.524 (38.71) 15/32 (11.91) 13/64 (5.16) 2 3/8 (60.33) 3 1/16 (77.79) NOTES: 1. Unless otherwise specified, dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, the tolerance for 3 place decimals is .005, the tolerance for fractions is 1/

9、64, the tolerance for degrees is 2. 4. Threads shall be in accordance with FED-STD-H28/2. FIGURE 1. Elbows, tube-safety sleeve compression type, 90 degree - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39207G 3 REQUIREMENTS: Dimension

10、s and configuration: See figure 1. Tolerances: Unless otherwise specified, decimals .005, fractions 1/64, degrees 2. Threads: The threads shall be in accordance with FED-STD-H28. Material: Code Material C Steel bar, type AISI-C-1112, C-1113, C-1117, C-1118 or C-1137 in accordance with SAE-AIR4127. F

11、 Alloy Steel, in accordance with SAE-AIR4127. S Corrosion resistant steel in accordance with SAE AMS5659, SAE AMS5862, or, alloy 15-5 PH in accordance with ASTM A564/A564M type XM-12 or UNS S15500, or SAE AMS5665. Chemical Finish: Code Finish C Carbon steel: Cadmium in accordance with SAE-AMS-QQ-P-4

12、16, type II, class 3, 200 inches to 300 inches (5.08 m to 7.62 m) thick. F Alloy Steel: Cadmium in accordance with SAE-AMS-QQ-P-416, type II, class 3, 200 inches to 300 inches (5.08 m to 7.62 m) thick. S Corrosion resistant steel: Passivate in accordance with SAE AMS2700, type 6 or 7. Z Steel, alter

13、native chem finish: ASTM B633, type VI, FeZn 25. Part or Identifying Number (PIN) example: (PIN covers the complete item with nuts and sleeves.) Guidance on use of alternative parts with less hazardous or non-hazardous materials. This specification provides an alternate material, corrosion resistant

14、 steel, and Zinc finish via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application. MS 27612 -8 C Z If finish code same as Material code, then use only one code. Material code Dash size Specification number MS p

15、refix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39207G 4 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience

16、 only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue Referen

17、ced documents. This document references the following: FED-STD-H28/2 ASTM A564/A564M ASTM B633 SAE-AIR4127 SAE AMS5659 FED-STD-H28 SAE AMS5665 SAE AMS5862 SAE AMS2700 SAE-AMS-QQ-P-416 MS39210 MS39212 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC DLA - CC (Project 4730-2012-0

18、40) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-