DLA MS39136 REV H-2012 SLEEVE COMPRESSION TUBE-HOSE FITTING AUTOMOTIVE AIR BRAKE HOSE ADAPTER.pdf

《DLA MS39136 REV H-2012 SLEEVE COMPRESSION TUBE-HOSE FITTING AUTOMOTIVE AIR BRAKE HOSE ADAPTER.pdf》由会员分享，可在线阅读，更多相关《DLA MS39136 REV H-2012 SLEEVE COMPRESSION TUBE-HOSE FITTING AUTOMOTIVE AIR BRAKE HOSE ADAPTER.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET SLEEVE COMPRESSION, TUBE-HOSE FITTING, AUTOMOTIVE AIR BRAKE HOSE ADAPTER This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sh

2、eet. Inches mm Inches mm Inches mm 0.003 0.076 0.190 4.826 0.838 21.285 0.005 0.127 0.310 7.874 0.843 21.412 0.030 0.762 0.656 16.662 0.875 22.225 0.093 2.362 0.690 17.526 0.906 23.012 0.135 3.429 0.796 20.218 FIGURE 1. Compression sleeve. AMSC N/A FSC 4730 INCH-POUND MS39136H 30 August 2012 SUPERSE

3、DING MS39136G 24 May 2010 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39136H 2 NOTES: 1. All dimensions are in inches. 2. Metric equivalents are given for information only. 3. For design feature purposes, this document takes precedence over acq

4、uisition documents referenced herein. 4. In the event of a conflict between the text of this specification sheet and the references cited herein, the text of this specification sheet shall take precedence. FIGURE 1. Compression sleeve Continued. REQUIREMENTS: Sleeves shall be specified on figure 1.

5、The sleeves specified herein are a component of the adapter, straight pipe to hose, automotive air brake hose MS39133. Materials shall conform to formed rod, tempered, half-hard brass as specified in ASTM-B16/B16M. Finish shall be uncoated. Tolerances for the compression sleeve, unless otherwise spe

6、cified, are as follows: XXX = .005 XX = .002 Angles 2 Buttress threads shall be in accordance with FED-STD-H28/14 and ASME-B1.9. Part or Identifying Number (PIN). Example of a PIN: MS39136-1 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate whe

7、re changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective o

8、f the marginal notations and relationship to the last previous issue. Referenced documents. This document references the following: MS39133 FED-STD-H28/14 ASME-B1.9 ASTM-B16/B16M Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39136H 3 CONCLUDING M

9、ATERIAL Custodians: Preparing activity: Army AT DLA - CC Navy SH Air Force 99 DLA CC (Project 4730-2012-035) Review activities: Army AR, EA Navy MC, SA Air Force 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-