DLA MS39135 REV G-2010 NUT HOSE COUPLING AUTOMOTIVE AIR BRAKE HOSE ADAPTER.pdf

《DLA MS39135 REV G-2010 NUT HOSE COUPLING AUTOMOTIVE AIR BRAKE HOSE ADAPTER.pdf》由会员分享，可在线阅读，更多相关《DLA MS39135 REV G-2010 NUT HOSE COUPLING AUTOMOTIVE AIR BRAKE HOSE ADAPTER.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET NUT, HOSE COUPLING, AUTOMOTIVE AIR BRAKE HOSE ADAPTER This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet. Inches mm Inch

2、es mm Inches mm 0.002 0.051 0.25 6.350 0.963 24.460 0.003 0.076 0.27 6.858 0.984 24.994 0.005 0.127 0.53 13.462 1.031 26.187 0.015 0.381 0.56 14.224 1.039 26.391 0.02 0.508 0.77 19.558 1.057 26.848 0.026 0.660 0.796 20.218 1.06 26.924 0.03 0.762 0.843 21.412 1.187 30.150 FIGURE 1. Hose coupling nut.

3、 AMSC N/A FSC 4730 INCH-POUND MS39135G 24 May 2010 SUPERSEDING MS39135F 4 January 1999 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39135G 2 TABLE I. Nut materials. MS dash number Material -1-B Brass -1-S Steel NOTES: 1. All dimensions are in in

4、ches. 2. Metric equivalents are given for information only. 3. For design feature purposes, this document takes precedence over acquisition documents referenced herein. 4. In the event of a conflict between the text of this specification sheet and the references cited herein, the text of this specif

5、ication sheet shall take precedence. 5. Part or Identifying Number (PIN). Example of a PIN: MS39135-1-B. FIGURE 1. Hose coupling nut - Continued. Inches mm Inches mm 0.005 0.127 0.875 22.225 0.07 1.778 0.915 23.241 0.25 6.350 1.25 31.750 0.70 17.780 FIGURE 2. Alternate design, hose coupling, nut. Pr

6、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39135G 3 TABLE II. Alternate design nut materials. MS dash number Material -A-1-B Brass -A-1-S Steel FIGURE 2. Alternate design, hose coupling, nut Continued. REQUIREMENTS: Nuts shall be as specified on

7、 figures 1 and 2 and tables I and II. The nuts specified herein are a component of the adapter, straight pipe to hose, automotive air brake hose MS39133. Materials shall conform to formed rod, tempered, half-hard brass as specified in ASTM-B16/B16M and steel as specified in ASTM-A108. Finishes for b

8、rass shall be uncoated and steel shall be zinc coated, thickness not less than 25m, type II, as specified in ASTM-B633. Tolerances for the nut, unless otherwise specified, are as follows: .XXX = .005 .XX = .02 Angles 2 Threads shall be in accordance with FED-STD-H28/2 and ASME-B1.1. Example of a PIN

9、: MS39135-1-B MS39135 -1 -B Specification sheet number Size dash number for pipe end (see table I) Material (see table I) Example of a PIN, alternate design: MS39135-A-1-B. MS39135 -A -1 -B Specification sheet number Dash letter for alternate design Size dash number for pipe end (see table II) Mater

10、ial (see table II) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39135G 4 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as

11、a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous

12、issue. Referenced documents. This document references the following: MS39133 FED-STD-H28/2 ASME-B1.1 ASTM-A108 ASTM-B16/B16M ASTM-B633 CONCLUDING MATERIAL Custodians: Preparing activity: Army AT DLA - CC Navy SH Air Force 99 DLA CC (Project 4730-2010-061) Review activities: Army AR, EA Navy MC, SA A

13、ir Force 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-