DLA MS39133 REV G-2010 ADAPTER STRAIGHT PIPE TO HOSE-AUTOMOTIVE AIR BRAKE HOSE.pdf

《DLA MS39133 REV G-2010 ADAPTER STRAIGHT PIPE TO HOSE-AUTOMOTIVE AIR BRAKE HOSE.pdf》由会员分享，可在线阅读，更多相关《DLA MS39133 REV G-2010 ADAPTER STRAIGHT PIPE TO HOSE-AUTOMOTIVE AIR BRAKE HOSE.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET ADAPTER, STRAIGHT, PIPE TO HOSE-AUTOMOTIVE AIR BRAKE HOSE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet. Inches mm

2、0.97 24.64 1.06 26.92 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. All dimensions are “reference” dimensions. 4. For design feature purposes, this document takes precedence over acquisition documents referenced herein. 5. In the event of a conflict bet

3、ween the text of this specification sheet and the references cited herein, the text of this specification sheet shall take precedence. FIGURE 1. Adapter. AMSC N/A FSC 4730 INCH-POUND MS39133G 24 May 2010 SUPERSEDING MS39133F 4 January 1999 Provided by IHSNot for ResaleNo reproduction or networking p

4、ermitted without license from IHS-,-,-MS39133G 2 TABLE I. Adapter dimensions and materials. MS dash no. Pipe end (NPTF Short) Material for MS39135 MS39136 MS39137 -1-B 1/4 Brass -1-S Steel -2-B 1/2 Brass -2-S Steel FIGURE 2. Alternate design adapter. TABLE II. Alternate design adapter dimensions and

5、 materials. MS dash no. Pipe end (NPTF Short) Material for MS39135-A MS39136-A MS39137-A -A-1-B 1/4 Brass -A-1-S Steel -A-2-B 1/2 Brass -A-2-S Steel Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39133G 3 REQUIREMENTS: Adapters shall be specified

6、on figures 1 and 2 and tables I and II. Materials shall conform to formed rod, tempered, half-hard brass as specified in ASTM-B16/B16M and steel as specified in ASTM-A108. Finishes for brass shall be uncoated and steel shall be zinc coated, thickness not less than 25m, type II, as specified in ASTM-

7、B633. Part or Identifying Number (PIN). Example of a PIN: MS39133-1-B. MS39133 -1 -B Specification sheet number Size dash number for pipe end (see table I) Material (see table I) Example of a PIN, alternate design: MS39133-A-1-B. MS39133 -A -1 -B Specification sheet number Dash letter for alternate

8、design Size dash number for pipe end (see table II) Material (see table II) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39133G 4 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where cha

9、nges from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the

10、marginal notations and relationship to the last previous issue. Referenced documents. This document references the following: MS39134 MS39135 MS39136 MS39137 ASTM-A108 ASTM-B16/B16M ASTM-B633 CONCLUDING MATERIAL Custodians: Preparing activity: Army AT DLA - CC Navy SH Air Force 99 DLA CC (Project 47

11、30-2010-025) Review activities: Army AR, EA Navy MC, SA Air Force 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-