DLA MS35644 REV G-2011 FILLER NECK FUEL TANK MILITARY VEHICLES.pdf

《DLA MS35644 REV G-2011 FILLER NECK FUEL TANK MILITARY VEHICLES.pdf》由会员分享，可在线阅读，更多相关《DLA MS35644 REV G-2011 FILLER NECK FUEL TANK MILITARY VEHICLES.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET FILLER NECK: FUEL TANK MILITARY VEHICLES Inactive for new design after 22 January 1999. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this s

2、pecification sheet. FIGURE 1. Filler neck. ASMC N/A FSC 2910 INCH-POUND MS35644G 09 May 2011 SUPERSEDING MS35644F 25 November 1986 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35644G 2 FIGURE 1. Filler neck Continued. Provided by IHSNot for Resa

3、leNo reproduction or networking permitted without license from IHS-,-,-MS35644G 3 FIGURE 1. Filler neck Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35644G 4 FIGURE 1. Filler neck Continued. Provided by IHSNot for ResaleNo reproductio

4、n or networking permitted without license from IHS-,-,-MS35644G 5 Inches mm Inches mm Inches mm Inches mm .030 0.76 . 188 4.78 .984 24.99 5.560 141.22 .050 1.27 . 375 9.53 1.310 33.27 5.625 142.88 .060 1.52 .469 11.91 1.969 50.01 8.660 219.96 .065 1.65 .563 14.30 2.375 60.33 10.625 269.88 .125 3.18

5、.625 15.88 3.563 90.50 35.500 901.70 .156 3.96 .875 22.23 4.310 109.47 NOTES: 1. Dimensions are in inches. Tolerances are .010 on decimals, 1 on angles. 2. Metric equivalents are given for information only. 3. For design feature purposes, this standard takes precedence over acquisition documents ref

6、erenced herein. 4. In the event of a conflict between the text of this standard and the references cited herein, the text of this standard shall take precedence. 5. This document is not intended to limit construction to features other than as shown herein by dimensions, notations or referenced docum

7、ents. FIGURE 1. Filler neck Continued. Requirements: Filler tube MS90908-1 is included as a part of filler neck assembly MS356441, 5 and 9. This neck shall mate with MS35645 cap, fuel tank: tactical vehicle, fording. Specified Test depicted in procurement specification referenced therein shall apply

8、. This neck shall also mate with caps MS51300 and MS53075. Material: Steel sheet, low-carbon 0.15% maximum, grade 1008 to 1012 HR or CR with temper 4 or temper 5 in accordance with QQ-S-698. Optional material: ASTM-A1011/A1011M, Grade CS, Type B, ASTM-A1008/A1008M, Grade CS, Type B, or tubing in acc

9、ordance with ASTM-A513 Grades 1008 or 1010. Steel sheet or strip hot rolled pickled and oiled or cold rolled oiled, drawing quality ASTM-A507; steel sheet Carbon cold rolled drawing quality ASTM-A619/A619M; steel carbon cold rolled strip temper 4 or 5 ASTM-A109/A109M. Joint at filler neck and upper

10、ring shall be air and water tight. Welding rod shall be type I in accordance with SAE-AMS6457. Resistance spot welding shall be in accordance with AWS-D8.7M and AWS-D8.9M. Arc welding shall be type I in accordance with AWS-D1.1/D1.1M. Solder shall be composition 40 or 50 in accordance with J-STD-004

11、, J-STD-005, and J-STD-006 or composition 40 or 50 in accordance with ASTM-B32. Parts shall be free from burrs and sharp edges. Protective coating prior to installation of strainer: Assembly shall be protected with zinc coating in accordance with ASTM-A153/A153M or zinc coating (electrodeposited) in

12、 accordance with ASTM-B633, Fe/Zn 5, type VI. Guide shall properly position and support filler tube MS90908-1 without binding. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35644G 6 Part or Identifying Number (PIN) Example of a PIN: MS35644-1 Typ

13、e of guide and neck (see figure 1) MS prefix and basic number PIN Type of guide Type of neck MS35644-1 Open Flange MS35644-5 Open Ring MS35644-9 Open Ring Marking shall consist of the PIN and manufacturers identification in accordance with MIL-STD-130. Changes from previous issue. Marginal notations

14、 are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. This document references the following: MIL-STD-130 ASTM-A1008/A1008M MS35645 ASTM-A1011/A1011M MS51300 ASTM-B32 MS53075 ASTM-B633 QQ-S-698 AWS-D1.1/D1.1M AST

15、M-A109/A109M AWS-D8.7M ASTM-A153/A153M AWS-D8.9M ASTM-A507 J-STD-004 ASTM-A513 J-STD-005 ASTM-A619/A619M J-STD-006 SAE-AMS6457 CONCLUDING MATERIAL Custodians: Preparing activity: Army AT DLA CC Navy SH Air Force 99 (Project 2910-2010-004) DLA CC Review activities: Army AR, CR4 Navy MC, SA, YD Air Fo

16、rce 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-