DLA MS33800 REV E-2004 CONNECTOR RECEPTACLE ELECTRICAL PIN CONTACT NO 8 12 14 AND 16 AWG WATERPROOF《防水的没有接触销的电连接器插座8 12 14和16 AWG》.pdf

《DLA MS33800 REV E-2004 CONNECTOR RECEPTACLE ELECTRICAL PIN CONTACT NO 8 12 14 AND 16 AWG WATERPROOF《防水的没有接触销的电连接器插座8 12 14和16 AWG》.pdf》由会员分享，可在线阅读，更多相关《DLA MS33800 REV E-2004 CONNECTOR RECEPTACLE ELECTRICAL PIN CONTACT NO 8 12 14 AND 16 AWG WATERPROOF《防水的没有接触销的电连接器插座8 12 14和16 AWG》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 MS33800E 9 July 2004 SUPERSEDING MS33800D 28 January 1988 DETAIL SPECIFICATION SHEET CONNECTOR, RECEPTACLE, ELECTRICAL, PIN CONTACT NO. 8, 12, 14 AND 16 AWG, WATERPROOF This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquirin

2、g the product described herein shall consist of this specification sheet. STYLE I FIGURE 1. Connector, receptacle (small), imperial dimensions (inch). AMSC N/A FSC 5935 INCH-POUND This is a design standard not to be used as an MS part number. Provided by IHSNot for ResaleNo reproduction or networkin

3、g permitted without license from IHS-,-MS33800E 2STYLE II NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance shall be .005 (.127 mm) on decimals, 1 on angles, and .015 (.381 mm) for rubber products. Inches mm Inc

4、hes mm Inches mm .002 .051 .125 3.175 .394 10.010 .003 .076 .137 3.480 .470 11.938 .020 .508 .157 3.988 .690 17.526 .060 1.524 .187 4.750 .700 17.780 .065 1.651 .218 5.580 .725 18.415 .079 2.007 .271 6.883 .118 3.000 .344 8.738 FIGURE 1. Connector, receptacle (small), imperial dimensions (inch) - Co

5、ntinued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MS33800E 3STYLE I FIGURE 2. Connector, receptacle (large), metric. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MS33800E 4STYLE II mm Inches mm

6、Inches mm Inches .051 .0020 3.00 .0398 6.88 .2708 .070 .0027 3.18 .3756 10.00 .3937 .076 .0029 3.48 .1370 11.94 .4700 .51 .0200 3.99 .1570 17.53 .6902 1.52 .0598 4.75 .1870 17.78 .7000 1.65 .0649 5.54 .2181 18.42 .7252 2.00 .0787 6.74 .2653 NOTES: 1. Dimensions are in millimeters. 2. Imperial (inch)

7、 dimensions are given for general information only. 3. Unless otherwise specified, tolerance shall be .13 (.005 inches) on decimals, 1 on angles, and .38 (.0150 inches) for rubber products. FIGURE 2. Connector, receptacle (large), metric - Continued. Provided by IHSNot for ResaleNo reproduction or n

8、etworking permitted without license from IHS-,-MS33800E 5REQUIREMENTS: Design and construction: see figures 1 and 2. For mating connectors see MS27143 and MS27144. Material: Shell: rubber, grade SC615, A1, C1, E3, F2 in accordance with ASTM D2000. Terminal: brass, composition 11 on 22 temper half ha

9、rd minimum in accordance with ASTM B121, ASTM B36, ASTM B16, ASTM B16M and ASTM B124. Protective finish terminal, silver plate, type II, grade A, .0002 minimum thickness, in accordance with ASTM B700. Style II to be used with ribbed connector to denote polarity. Style II dimensions identical to styl

10、e I except as noted. Terminal shall be attached to component and shall withstand a full test of 100 pounds (46 kilograms). For multiple connector design, minimum cavity center distance shall be 600 inches. When connectors are coupled, the voltage drop shall not exceed 20 millivolts when tested in a

11、20-volt circuit as outlined in MIL-STD-202, method 307. When connectors are coupled, the assembly shall meet the 1000-volt requirement of the dielectric strength test outlined in MIL-STD-202, method 302. When connectors are coupled, waterproofness shall be achieved. For guidance on waterproofness, s

12、ee MIL-HDBK-1184. When connectors are coupled, the assembly shall meet the requirements of salt spray corrosion test outlined in MIL-STD-202, method 101 (5% saline, 200 hrs.) Recycled, virgin and reclaimed materials: There are no requirements for the exclusive use of virgin materials; however, all m

13、aterials shall be new and unused. The use of recycled or reclaimed (recovered) materials is acceptable provided that all other requirements of this document are met. All provisions of this standard are the subjects of international standardization agreement NATO-STANAG 4040. When revision or cancell

14、ation of this standard is proposed which will effect or violate the international agreement concerned, the preparing activity will take appropriate reconciliation action through international standardization channels, including departmental standardization offices, if required. Changes from previous

15、 issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MS33800E 6Reference documents. This document references th

16、e following: MS27143 MS27144 MIL-STD-202 MIL-HDBK-1184 ASTM B16/B16M ASTM B36 ASTM B121 ASTM B124 ASTM B700 ASTM D2000 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 11 DLA - CC (Project 5935-4419-027) Review activities: Army - AR, CR, CR4, GL Navy - MC

17、NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/www.dodssp.daps.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-