DLA MS27558 REV E-2009 SUPPORT CABLE RIGHT ANGLE CLOSED.pdf

《DLA MS27558 REV E-2009 SUPPORT CABLE RIGHT ANGLE CLOSED.pdf》由会员分享，可在线阅读，更多相关《DLA MS27558 REV E-2009 SUPPORT CABLE RIGHT ANGLE CLOSED.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET SUPPORT, CABLE, RIGHT ANGLE, CLOSED This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26500. FIGURE 1. Dime

2、nsions and configuration. AMSC N/A FSC 5935 INCH-POUND MS27558E 14 August 2009 SUPERSEDING MS27558D 06 February 2004 Inactive for new design after 14 November 1977. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27558E 2 MS Part or Identifying Num

3、ber (PIN) Size A dia B dia max C dia max MS27558-1 8 .348 .532 .672 MS27558-2 10 .440 .657 .797 MS27558-3 12 .600 .845 1.016 MS27558-4 14 .684 .907 1.110 MS27558-5 16 .789 1.032 1.234 MS27558-6 18 .922 1.157 1.360 MS27558-7 20 1.053 1.282 1.485 MS27558-8 22 1.172 1.407 1.610 MS27558-9 24 1.302 1.532

4、 1.735 MS PIN D Thread UNEF-2B E max F max G max H dia MS27558-1 .4375-28 1.200 .602 .892 .240 MS27558-2 .5625-24 1.320 .650 1.072 .365 MS27558-3 .750-20 1.320 .740 1.072 .365 MS27558-4 .8125-20 1.487 .775 1.108 .515 MS27558-5 .9375-20 1.470 .830 1.108 .515 MS27558-6 1.0625-18 1.588 .897 1.233 .640

5、MS27558-7 1.1875-18 1.759 .955 1.477 .775 MS27558-8 1.3125-18 1.759 1.015 1.477 .775 MS27558-9 1.4375-18 2.027 1.077 1.727 1.060 FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27558E 3 Inches mm Inches mm In

6、ches mm Inches mm Inches mm .010 .25 .532 13.51 .830 21.08 1.072 27.23 1.360 34.54 .032 .81 .600 15.24 .845 21.46 1.077 27.36 1.407 35.74 .035 .89 .602 15.29 .892 22.66 1.108 28.14 1.470 37.34 .042 1.07 .640 16.26 .997 22.78 1.110 28.19 1.477 37.52 .240 6.10 .650 16.51 .907 23.04 1.157 29.39 1.485 3

7、7.72 .262 6.65 .657 16.69 .922 23.42 1.172 29.77 1.532 38.91 .335 8.51 .672 17.07 .955 24.26 1.200 30.48 1.588 40.34 .348 8.84 .684 17.37 1.015 25.78 1.233 31.32 1.610 40.89 .365 9.27 .740 18.80 1.016 25.81 1.234 31.34 1.727 43.87 .440 11.18 .775 19.68 1.032 26.21 1.282 32.56 1.735 44.07 .487 12.37

8、.789 20.04 1.053 26.75 1.302 33.07 1.750 44.45 .515 13.08 .797 20.24 1.060 26.92 1.320 33.53 2.027 51.49 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .010. FIGURE 1. Dimensions and configuration Contin

9、ued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27558E 4 REQUIREMENTS Design and construction: Dimensions and configuration: See figure 1. Coupling nut securely captivated to cable support and has provisions for locking in an indexed position.

10、 Material and finish: Aluminum components anodized in accordance with MIL-A-8625 or suitable hard anodizing process to meet the performance requirements of MIL-DTL-26500. Cable support material: Aluminum alloy in accordance with ASTM-B26/B26M, composition 13, A13, A380, or 380. Coupling nut material

11、: Aluminum alloy in accordance with ASTM-B211 or SAE-AMS-QQ-A-367. Threads shall be in accordance with MIL-S-7742. PIN: MS27558- (see figure 1 tables for dash numbers). Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issu

12、e due to the extent of the changes. Referenced documents. In addition to MIL-DTL-26500, this document references the following: ASTM-B26/B26M ASTM-B211 MIL-A-8625 MIL-S-7742 SAE-AMS-QQ-A-367 NASM35275 NASM35338 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

13、 IHS-,-,-MS27558E 5 CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 85 DLA CC DLA CC Review activity: Air Force - 99 (Project 59352009-123) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-