DLA MS27511 REV L-2010 COVERS PROTECTIVE ELECTRICAL CONNECTOR RECEPTACLE BAYONET COUPLING SERIES II.pdf

《DLA MS27511 REV L-2010 COVERS PROTECTIVE ELECTRICAL CONNECTOR RECEPTACLE BAYONET COUPLING SERIES II.pdf》由会员分享，可在线阅读，更多相关《DLA MS27511 REV L-2010 COVERS PROTECTIVE ELECTRICAL CONNECTOR RECEPTACLE BAYONET COUPLING SERIES II.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET COVERS, PROTECTIVE, ELECTRICAL, CONNECTOR RECEPTACLE, BAYONET COUPLING, SERIES II This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specifi

2、cation sheet and MIL-DTL-38999. FIGURE 1. Cover. AMSC N/A FSC 5935 MS27511L 2 February 2010 SUPERSEDING MS27511K 12 July 2002 INCH-POUND Reactivated after 10 June 2005 and may be used for new and existing designs and acquisitions. Provided by IHSNot for ResaleNo reproduction or networking permitted

3、without license from IHS-,-,-MS27511L 2 FIGURE 1. Cover Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27511L 3 Shell size A dia max D E min ring throat H +.500 -.250 standard chain or rope length J .015 M max dia N min dia Q max dia ma

4、x min 8 .630 1.13 .80 .23 3.0 3.50 .082 1.22 .89 .750 10 .761 1.23 .93 1.42 1.01 .859 12 .936 1.29 .99 1.55 1.14 1.031 14 1.074 1.35 1.05 1.68 1.26 1.156 16 1.172 1.41 1.11 1.80 1.39 1.281 18 1.304 1.47 1.18 1.92 1.51 1.406 20 1.435 1.54 1.24 4.0 .107 2.05 1.64 1.531 22 1.560 1.60 1.30 2.18 1.76 1.6

5、41 24 1.688 1.66 1.36 2.30 1.89 1.766 Inches mm Inches mm Inches mm Inches mm Inches mm .002 .05 .57 14.5 1.11 28.2 1.36 34.5 1.66 42.2 .004 .10 .630 16.00 1.13 28.7 1.39 35.3 1.68 42.7 .005 .13 .750 19.05 1.14 29.0 1.406 35.71 1.688 42.87 .010 .25 .761 19.33 1.156 29.36 1.41 35.8 1.76 44.7 .015 .38

6、 .80 20.3 1.172 29.77 1.42 36.1 1.766 44.86 .030 .76 .82 20.8 1.18 30.0 1.435 36.45 1.80 45.7 .094 2.39 .859 21.82 1.22 31.0 1.47 37.3 1.89 48.0 .107 2.72 .89 22.6 1.23 31.2 1.51 38.4 1.92 48.8 .1 3.0 .93 23.6 1.24 31.5 1.531 38.90 2.05 52.1 .125 3.18 .936 23.77 1.26 32.0 1.54 39.1 2.18 55.4 .141 3.

7、58 .99 25.1 1.281 32.54 1.55 39.4 2.30 58.4 .167 4.24 1.01 25.7 1.29 32.8 1.560 39.62 3.00 76.2 .23 5.8 1.031 26.19 1.30 33.0 1.60 40.6 3.50 88.9 .25 6.4 1.05 26.7 1.304 33.12 1.64 41.65 4.00 101.6 .50 12.7 1.074 27.28 1.35 34.3 1.641 41.68 NOTES: 1. Dimensions are in inches. 2. Metric equivalents a

8、re given for general information only. 3. Finish: See MIL-DTL-38999. 4. Not for space born applications. FIGURE 1. Cover Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27511L 4 REQUIREMENTS: Dimensions and configuration: See figure 1. I

9、nterface dimensions shall conform to MIL-DTL-38999. Material: Ring - Passivated stainless steel, .030 maximum thickness. Cover - Impact extruded or machined aluminum alloy. Disk - Silicone or fluorosilicone elastomer. Chain - Passivated stainless steel, conforming to RR-C-271, type II, class 3. Wire

10、 rope - Insulated, braided steel wire. Fastener - Passivated stainless steel. Eyelets shall be crimped over wire rope as to ensure a breaking strength equal to or greater than that of the wire rope. Mating connectors: MIL-DTL-38999 Series II receptacles and MIL-DTL-27599 Series II receptacles. Disk

11、shall be bonded to cover, or mechanically retained. The chain or rope assembly shall rotate freely on the cover fastener. The protective cover and rope assembly shall withstand a static tensile load of 35 pounds applied along the B reference line for 5 minutes. Fastener tensile strength: Both axial

12、and longitudinal directions shall be 25 pounds. The load shall be applied to the end of the chain or wire rope. Qualification: Examination of product. Mating and unmating forces. Humidity. Salt spray (corrosion). Fastener tensile strength (see requirement). Altitude immersion. Group A sampling inspe

13、ction. 100% inspection is not applicable. Sampling inspection shall be as specified in table I: TABLE I. Group A sampling plan. Lot size Sample size 1 to 13 14 to 150 151 to 280 281 to 500 501 to 1,200 1,201 to 3,200 100 percent 13 units 20 units 29 units 34 units 42 units Provided by IHSNot for Res

14、aleNo reproduction or networking permitted without license from IHS-,-,-MS27511L 5 Part or Identifying Number (PIN) example: MS27511 F 12 C L MS number Finish Shell Size Style C - Chain N - With chain and ring R - Rope A - Without chain or rope Length L- 5-inch chain in lieu of standard length. Leav

15、e blank for standard length. Applicable to chain only. Not applicable to style R. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-38999,

16、 this document references the following: MIL-DTL-27599 RR-C-271 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA CC Navy AS Air Force 85 (Project 59352009-155) DLA CC Review activities: Army AR, MI Navy EC, MC, OS Air Force 19, 99 NOTE: The activities listed above were interested in t

17、his document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-