DLA MS27247 REV M-2003 RELAYS ELECTROMAGNETIC 10 AMPERES 2 PDT TYPE I HERMETICALLY SEALED《I型2 PDT 10安培密封电磁继电器》.pdf

《DLA MS27247 REV M-2003 RELAYS ELECTROMAGNETIC 10 AMPERES 2 PDT TYPE I HERMETICALLY SEALED《I型2 PDT 10安培密封电磁继电器》.pdf》由会员分享，可在线阅读，更多相关《DLA MS27247 REV M-2003 RELAYS ELECTROMAGNETIC 10 AMPERES 2 PDT TYPE I HERMETICALLY SEALED《I型2 PDT 10安培密封电磁继电器》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A 1 of 6 FSC 5945 INCH-POUND MS27247M 27 November 2003 SUPERSEDING MS27247L 22 Jul 1992 DETAIL SPECIFICATION SHEET RELAYS, ELECTROMAGNETIC, 10 AMPERES, 2 PDT TYPE I, HERMETICALLY SEALED INACTIVE FOR NEW DESIGN AFTER 5 JUNE 1987. NO SUPERSEDING SPECIFICATION. FOR NEW DESIGN, USE MIL-PRF-83536/

2、9, 10, 11. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-PRF-6106. FIGURE 1. Dimensions and configuration. Provided by IHSN

3、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27247M 2 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27247M 3 Inches mm Inches mm Inches mm .0001 0.025 .14

4、4 3.66 1.000 25.40 .002 0.05 .156 3.96 1.015 25.78 .005 0.13 .200 5.08 1.356 34.44 .010 0.25 .210 5.33 1.484 37.69 .015 0.38 .213 5.41 1.719 43.66 .050 1.27 .375 9.52 1.750 44.45 .062 1.57 .515 13.08 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3.

5、 Unless otherwise specified, tolerance is .010 (0.25 mm). 4. Terminal numbers need not appear on relay headers provided there is affixed to the relay a suitable legible circuit diagram that identifies each terminal location specified. 5. Socket pin terminals shall provide the operational, environmen

6、tal, and interface characteristics to provide a reliable interconnect to gold-plated contacts. Terminals shall be gold plated. One system for gold plating that may be used is ASTM B488, type 3, class 1.25 with a nickel underplate of 50 to 150 microinches thick. The gold plating system shall enable t

7、he product to meet the performance requirements of this specification and shall be approved by the qualifying activity. 6. Gasket shall provide a reliable seal between the relay and mating socket that will meet the environmental, operational, and interface requirements of the relay with the mating s

8、ocket. The gasket shall have shore hardeness 20 5, thickness .050 .05. Gasket material according to AMS 3332 has been considered acceptable. FIGURE 1. Dimensions and configurations - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27247M

9、4 REQUIREMENTS: Dimensions, and configurations: See figure 1. ENVIRONMENTAL CHARACTERISTICS: Temperature range: -70C and +125C. Maximum altitude rating: 80,000 feet. Shock g-level: 50 gs. Duration: 11 ms. Max duration contact opening: 10 s. Vibration - sinusoidal: G-level: 20 gs. Frequency range: 10

10、 - 2,000 Hz. Acceleration: 15 gs. ELECTRICAL CHARACTERISTICS (see tables I, II, III, AND IV). Insulation resistance, initial: 100 megohms. After life or environmental tests: 50 megohms. Dielectric strength (sea level): Initial After life tests Coil to case 1,000 V rms 1,000 V rms Aux contacts N/A N/

11、A All other points 1,250 V rms 1,000 V rms Dielectric strength (altitude): 80,000 feet. Initial After life tests Coil to case N/A 350 V rms Aux contacts N/A All other points N/A 350 V rms Maximum contact drop initial: 0.150 volt. After life test: 0.175 volt. Overload current: 20 amperes, 28 V dc. Ru

12、pture current: 40 amperes, 115 V ac, 400 Hz. Duty rating: Continuous. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27247M 5 CONFORMANCE INSPECTION: Performance of groups B and C tests are not applicable. Group A acceptance reports shall be submi

13、tted to the qualifying activity on a yearly basis in order to retain qualification for this military specification sheet. Qualification by similarity: See MIL-PRF-6106. TABLE I. Dash numbers and characteristics. PIN number MS27247- Type Coil Terminal type 115/200 V ac 3 phase contact rating Mounting

14、 or mating sockets Max weight in pounds 1 I dc Plug-in N/A N/A .08 2 I dc Plug-in Applicable N/A .08 3 IER dc Plug-in Applicable N/A .08 4 I dc Printed wire (PW) N/A N/A .08 5 I dc Printed wire (PW) Applicable N/A .08 TABLE II. Operating characteristics. Coil data Time - (milliseconds maximum) Nomin

15、al Max Max pick-up voltage Contact Bounce Main AuxPIN MS 27247- Coil Volts 1/ Freq Hz Res 10% Volts Amp Nor- mal 2/ High temptest Cont cur-rent test Hold vol- tage 2/ Drop out volt- age 2/ Oper-ate 3/ Rel-ease 4/ NO NC NO NC MS27247-1 dc 28 dc 300 29 .120 18 18 19.8 7 1 10 10 2 5 - - MS27247-2 dc 28

16、 dc 300 29 .120 18 18 19.8 7 1 10 10 2 5 - - MS27247-3 dc 28 dc 300 29 .120 18 18 19.8 7 1 10 10 2 5 - - MS27247-4 dc 28 dc 300 29 .120 18 18 19.8 7 1 10 10 2 5 4 4 MS27247-5 dc 28 dc 300 29 .120 18 18 19.8 7 1 10 10 2 5 - - 1/ Caution: Use of any coil voltage less than nominal coil voltage will com

17、promise the operation of the relay. 2/ Over the temperature range. 3/ With rated coil voltage. 4/ From rated coil voltage. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27247M 6 TABLE III. Rated contact load (amperes per pole) (case grounded). 28

18、 V dc 115 V ac, 1 phase 115/200 V ac, 3 phase 1/ Main Aux Main Aux Main Aux Type of load Life operating cycles x 103 1/NO NC NO NC 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz See appropriate notes Resistive 100 10 10 10 10 Inductive 100 4 4 4 4 e Motor 100 3 3 3 3 Lamp 100 2 2 2 2 Transfer l

19、oad 3/ Mechanical life reduced current 400 2.5 2.5 Mixed loads 4/ 1/ 115/200 V ac for 60 Hz ratings, absence of value indicates relay is not rated for 3-phase applications. 2/ Additional rating for -5 only: 2 ampere inductive at 460 V ac, 400 Hz. 3/ Transfer load indicates relay is suitable for tran

20、sfer between unsynchronized ac power supplies at rating indicated. 4/ Minimum current ratings 0.1 ampere resistive, 0.3 ampere inductive, and 0.5 ampere resistive are applicable in accordance with acquisition specifications except monitored to a 3 ohm contact resistance. NOTES Referenced documents.

21、In addition to MIL-PRF-6106, this specification sheet references the following documents. (Government documents are available on line at http:/assist.daps.dla.mil/quicksearch or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191

22、11-5094). Society of Automotive Engineers documents are available from the Society of Automotive Engineers 400 Commonwealth Drive Warrendale, Pennsylvania, United States, 15096-0001. http:/www.sae.org American Society for Testing and Materials documents are available from the American Society for Te

23、sting and Materials 100 Barr Harbor Drive , West Conshohocken, Pennsylvania, United States 19428-2959. http:/www.astm.org/ American Society for Testing and Materials (ASTM) ASTM-E8 - Materials, Metallic, Tension Testing of Society of Automotive Engineers (SAE) SAE-AMS3332 - Silicone Rubber Extreme L

24、ow-Temperature Resistant, 15-30 Custodians: Preparing activity:NAVY - EC DLA - CC Air Force - 11 DLA - CC (Project 5945-1221-01) Review activities: Navy - AS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at www.dodssp.daps.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-