DLA MS27235 REV D-2007 ELBOW TUBE 45 DEG 《45度弯管》.pdf
《DLA MS27235 REV D-2007 ELBOW TUBE 45 DEG 《45度弯管》.pdf》由会员分享,可在线阅读,更多相关《DLA MS27235 REV D-2007 ELBOW TUBE 45 DEG 《45度弯管》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 MS27235D INCH-POUND14 May 2007 SUPERSEDING MS27235C 22 September 2000 DETAIL SPECIFICATION SHEET ELBOW TUBE, 45 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this spec
2、ification sheet and MIL-DTL-5070. FIGURE 1. Elbow dimensions and configuration. AMSC N/A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FSC 4730 MS27235D 2 Dash number A .015 (0.38) inches (mm) B .015 (0.38) inches (mm) C +.031 (0.79) -.000 inches (
3、mm) D Dia .005 (0.13) inches (mm) (see note 5)E Rad .060 (1.52) inches (mm) Ttube wall thickness inches (mm) X inches (mm)(see note 6)-4 .531 (13.49) .220 (5.59) .245 (6.22) .375 (9.53) .035 (.89) .010 (.25) -5 .575 (14.61) .238 (6.05) .307 (7.80) .438 (11.13) .012 (.30) -6 .370 (9.40).049 (1.24) .0
4、14 (.36) -8 .620 (15.75) .256 (6.50) .495 (12.57).500 (12.70).016 (.41) -10 .708 (17.98) .293 (7.44) .156 (3.96).620 (15.75).625 (15.88) .018 (.46) -12 1.024 (26.01) .424 (10.77) .745 (18.92).844 (21.44) .020 (.51) -16 1.112 (28.24) .461 (11.71) .995 (25.27).969 (24.61) .022 (.56) -20 1.266 (32.16)
5、.525 (13.34) 1.245 (31.62) 1.188 (30.18) .065 (1.65) .024 (.61) -24 1.399 (35.53) .580 (14.73) 1.495 (37.97) 1.375 (34.93) .026 (.66) -32 1.664 (42.27) .690 (17.53) 1.995 (50.67) 1.750 (44.45) .083 (2.11) .028 (.71) -40 1.885 (47.88) .781 (19.84) 2.370 (60.20) 2.062 (52.37) -48 2.062 (52.37) .854 (2
6、1.69) .250 (6.35)2.995 (76.07) 2.312 (58.72) .095 (2.41) .030 (.76) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for information only. 3. Unless otherwise specified, break all corners, radius .010/.005 inch (0.25/0.13 mm). 4. Break all edges and remove all burrs and slivers. 5. Oval
7、ity at bend shall not exceed 5% of tubing outside diameter. 6. Face of tube must be perpendicular to centerline of the tube within X total indicator reading. FIGURE 1. Elbow dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
| 下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMS27235REVD2007ELBOWTUBE45DEG45 弯管 PDF
麦多课文档分享所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
链接地址:http://www.mydoc123.com/p-696686.html



GB T 32280-2015 硅片翘曲度测试 自动非接触扫描法.pdf
2019届中考物理第一轮重点专题突破三情景开放性试题复习课件20190107457.ppt

