DLA MS27231 REV B-2007 STRAIGHT FLANGE NIPPLE ASSEMBLY ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的螺纹接口液压法兰软管组件适配器》.pdf

《DLA MS27231 REV B-2007 STRAIGHT FLANGE NIPPLE ASSEMBLY ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的螺纹接口液压法兰软管组件适配器》.pdf》由会员分享，可在线阅读，更多相关《DLA MS27231 REV B-2007 STRAIGHT FLANGE NIPPLE ASSEMBLY ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的螺纹接口液压法兰软管组件适配器》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 MS27231B INCH-POUND14 May 2007 SUPERSEDING MS27231A 22 September 2000 DETAIL SPECIFICATION SHEET STRAIGHT FLANGE NIPPLE ASSEMBLY, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES This specification is approved for use by all Departments and Agencies of the Department of Defense. The r

2、equirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. FIGURE 1. Nipple dimensions and configuration. AMSC N/A FSC 4730 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27231B 2 MS27231 das

3、h number A (ref) inches (mm) B .010 (0.25)inches (mm)C .020 (0.51)inches (mm)D inches (mm) E Dia inches (mm)-8 2.750 (69.85) .561 (14.25) .360 (9.14) .355 (9.02) -10 2.925 (74.30) .687 (17.45) .460 (11.68).450 (11.43)-12 3.219 (81.76) .875 (22.23) .582 (14.78).576 (14.63)-16 2.723 (69.16) 1.125 (28.

4、58) .820 (20.83).810 (20.57)-20 2.896 (73.56) 1.125 (28.58) .810 (20.57)1.375 (34.93) 1.052 (26.72)1.042 (26.47)-24 2.873 (72.97) 1.062 (26.97) .750 (19.05) 1.625 (41.28) 1.286 (32.66)1.276 (32.41)-32 3.507 (89.08) 1.241 (31.52) .940 (23.88) 2.125 (53.98) 1.755 (44.58)1.745 (44.32)-40 2.625 (66.68)

5、2.219 (56.36)2.199 (55.85)-48 3.844 (97.64) 1.375 (34.93) 1.060 (26.92)3.250 (82.55) 2.823 (71.70)2.803 (71.20)NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances are .005 inch (0.13 mm). 4. Unless otherwise specified, ma

6、ximum surface roughness shall be 125 in Rain accordance with ASME B46.1. 5. Shoulder end F shall be in accordance with MS27237. 6. Nipple end G shall be in accordance with MS27239. 7. Break all sharp edges and remove all burrs and slivers. 8. Part or Identifying Number (PIN). FIGURE 1. Nipple dimens

7、ions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27231B 3 REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in cas

8、e of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use: This part is a component of MS27232. Material: Aluminum shall be accordance with MIL-DTL-5070. Finish. Finish shall be accordance with MIL-DTL-5070. Color identification: Color identification shall be in ac

9、cordance with MIL-DTL-5070. PIN example: MS 27231 -3 AAMaterial/finish code, see table I Dash number on figure 1 Specification number MS prefix TABLE I. Code for material and finish. Code Dash size Material/finish AA -8 through-48 Aluminum anodic coating Identification of product. The PIN and the ma

10、nufacturers Commercial and Government Entity (CAGE) Code or trademark shall be permanently marked on the nipple, see figure 1, or on a removable tag securely attached to the nipple. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the

11、previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-5070, this document references the following: MS27232 MS27237 MS27239 ASME B46.1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27231B 4 CONCLUDING MATE

12、RIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-050) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-