DLA MS27225 REV C-2007 NIPPLE ASSEMBLY 45 DEG ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的45度螺纹接口软管组件适配器》.pdf

《DLA MS27225 REV C-2007 NIPPLE ASSEMBLY 45 DEG ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的45度螺纹接口软管组件适配器》.pdf》由会员分享，可在线阅读，更多相关《DLA MS27225 REV C-2007 NIPPLE ASSEMBLY 45 DEG ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES《可重复使用的45度螺纹接口软管组件适配器》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUNDMS27225C 14 May 2007 SUPERSEDING MS27225B 7 September 1999 DETAIL SPECIFICATION SHEET NIPPLE ASSEMBLY 45, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements fo

2、r acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. FIGURE 1. 45 Nipple assembly dimensions and configuration. AMSC N/A FSC 4730 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27225C 2 D Wire PIN E

3、Shoulder PIN F Nut PIN (see note 4) G Nipple PIN H Elbow PIN Dash number A .035 (0.89) inches (mm) B .035 (0.89) inches (mm) C inches (mm) MS27238 MS27236 SAE-AS4370 MS27239 MS27235 K Rad (ref) inches (mm) -4 .758 (19.25) .352 (8.94) .37 (9.40) -4 -4 -4 -4 -4 .38 (9.65) -5 .909 (23.09) .415 (10.54)

4、.38 (9.65) -5 -5 -5 -5 -5 .44 (11.18) -6 .965 (24.51) .444 (11.28) .38 (9.65) -6 -6 -6 -6 -6 -8 1.039 (26.39) .456 (11.58) .44 (11.18) -8 -8 -8 -8 -8 .50 (12.70) -10 1.171 (29.74) .536 (13.61) .50 (12.70) -10 -10 -10 -10 -10 .62 (15.75) -12 1.348 (34.24) .625 (15.88) .57 (14.48) -12 -12 -12 -12 -12

5、.84 (21.34) -16 1.436 (36.47) .660 (16.76) .63 (16.00) -16 -16 -16 -16 -16 .97 (24.64) -20 1.760 (44.70) .768 (19.51) .64 (16.26) -20 -20 -20 -20 -20 1.19 (30.23) -24 1.999 (50.77) .867 (22.02) .77 (19.56) -24 -24 -24 -24 -24 1.38 (35.05) -32 2.415 (61.34) 1.066 (27.08) .92 (23.37) -32 -32 -32 -32 -

6、32 1.75 (44.45) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are as follows: angles 1; decimals .005 inches (0.01 mm). 4. Nut shall swivel freely after assembly. 5. Part or Identifying Number (PIN). FIGURE 1. 45 N

7、ipple assembly dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended

8、 use: This part is a component of MS27226. Materials: Materials shall be in accordance with MIL-DTL-5070. Finish: Finish shall be in accordance with MIL-DTL-5070. Platings are applied after heat treats and before assembling nut. Color identification: Color identification shall be in accordance with

9、MIL-DTL-5070. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27225C 3 Braze. Steel: Braze at points J in accordance with AWS C3.4, AWS C3.5, AWS C3.6, or AWS C3.7. Aluminum: Braze at points J in accordance with SAE-AMS2672. Titanium: Braze at poin

10、ts J. Heat treatment: Steel: Heat treat in accordance with SAE-AMS-H-6875 after braze so that Rockwell hardness of nipple is C-25. Aluminum: Heat treat in accordance with SAE-AMS2770, condition T6, after braze. Titanium: Heat treatment in accordance with SAE-AMS2801, temper STA900, after braze. PIN

11、example: MS 27225 -4 CZ Material/finish designator, see table I Dash number on figure I Specification number MS prefix TABLE I. Code for material and finish. Code Dash size Material/finish CC -4 through -6 Carbon Steel - cadmium plating CZ -4 through -6 Carbon steel - zinc plating SS -4 through -6 C

12、orrosion resistant steel - N/A AA -8 through -32 Aluminum - anodic coating TA -4 through -32 Titanium - anodized or fluoride phosphated. To the users of this document, it is recommended that the use of carbon steel material with cadmium plating be used only when the other materials and finishes spec

13、ified in this document cannot meet performance requirements. Identification of product. The PIN and the manufacturers Commercial and Government Entity (CAGE) Code or trademark shall be permanently marked on the assembly, see figure 1, or marked on a removable tag securely attached to the assembly. C

14、hanges from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27225C 4 Referenced documents. In

15、 addition to MIL-DTL-5070, this document references the following: MS27226 MS27235 MS27236 MS27238 MS27239 AWS C3.4 AWS C3.5 AWS C3.6 AWS C3.7 SAE-AMS-H-6875 SAE-AMS2801 SAE-AMS2672 SAE-AMS2770 SAE-AS4370 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99

16、 (Project 4730-2005-044) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-