DLA MS27224 REV B-2007 SWIVEL NUT ASSEMBLY 90 ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES 1 4 INCH THROUGH 2 1 2 INCH TUBE SIZES《通过1 4英寸至2 1 2英寸的石油管道可重复使用的90度旋转螺母法兰软.pdf

《DLA MS27224 REV B-2007 SWIVEL NUT ASSEMBLY 90 ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES 1 4 INCH THROUGH 2 1 2 INCH TUBE SIZES《通过1 4英寸至2 1 2英寸的石油管道可重复使用的90度旋转螺母法兰软.pdf》由会员分享，可在线阅读，更多相关《DLA MS27224 REV B-2007 SWIVEL NUT ASSEMBLY 90 ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES 1 4 INCH THROUGH 2 1 2 INCH TUBE SIZES《通过1 4英寸至2 1 2英寸的石油管道可重复使用的90度旋转螺母法兰软.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUNDMS27224B 14 May 2007 SUPERSEDING MS27224A 22 September 2000 DETAIL SPECIFICATION SHEET SWIVEL NUT ASSEMBLY 90, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES 1/4 INCH THROUGH 2 1/2 INCH TUBE SIZES This specification is approved for use by all Departments and Agencies of th

2、e Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. FIGURE 1. 90 swivel nut assembly dimensions and configuration. AMSC N/A Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

3、e from IHS-,-,-FSC 4730MS27224B 2 Nipple assemblyPIN (see note 3) Socket PIN Dash number MS27223 MS24590-4 -4 -4 -5 -5 -5-6 -6 -6 -8 -8 -8-10 -10 -10 -12 -12 -12MS24591-16 -16 -16 -20 -20 -20-24 -24 -24 -32 -32 -32NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information on

4、ly. 3. Part or Identifying Number (PIN). FIGURE 1. 90 swivel nut assembly dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this dr

5、awing and MIL-DTL-5070, this drawing shall govern. Intended use. This assembly is designed for use with hose conforming to MIL-DTL-8794. Materials. Materials shall be in accordance with MIL-DTL-5070. Finish. Finish shall be in accordance with MIL-DTL-5070. Color identification: Color identification

6、shall be in accordance with MIL-DTL-5070. PIN example: MS 27224 -4 CZMaterial/finish code, see table I Dash number on figure 1 Specification number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27224B 3 TABLE I. Code for material and fi

7、nish. Code Dash size Material/finish CC -4 through -6 Carbon Steel - cadmium plating CZ -4 through -6 Carbon steel - zinc plating SS -4 through -6 Corrosion resistant steel - N/A AA -8 through -32 Aluminum - anodic coating TA -4 through -32 Titanium - anodized or fluoride phosphated. Identification

8、of product. The PIN and the manufacturers Commercial and Government Entity (CAGE) Code or trademark shall be marked on a removable tag securely attached to the assembly. Referenced documents: In addition to MIL-DTL-5070, this document references the following: MS27223 MS24590 MS24591 MIL-DTL-8794 Ch

9、anges from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-043) DLA - CC Revie

10、w activities: Army - AV Navy - MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-