DLA MS25224 REV H-2006 GUARD SWITCH 2 POSITION《2号定位开关防护装置》.pdf

《DLA MS25224 REV H-2006 GUARD SWITCH 2 POSITION《2号定位开关防护装置》.pdf》由会员分享，可在线阅读，更多相关《DLA MS25224 REV H-2006 GUARD SWITCH 2 POSITION《2号定位开关防护装置》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5930 MS25224H 1 February 2006 SUPERSEDING MS25224G 20 December 1982 DETAIL SPECIFICATION SHEET GUARD, SWITCH, 2 POSITION This specification is approved for use by all Departments and Agencies of the Department of Defense. The complete requirements for acquiring the switch described here

2、in shall consist of this specification and the latest issue of MIL-DTL-7703. SUITABLE FOR USE WITH SWITCHES HAVING TOGGLE CHARACTERISTICS IN ACOORDANCE WITH DETAIL A (1-HOLE MOUNTING) FIGURE 1 Dimensions and configuration. INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitte

3、d without license from IHS-,-,-MS25224H 2-2 SUITABLE FOR USE WITH SWITCHES HAVING TOGGLE CHARACTERISTICS IN ACCORDANCE WITH DETAIL B (3-HOLE MOUNTING) DASH NO. TYPE PANEL THICKNESS (REF) OPERATING FORCE REMARKS -1 1- HOLE MOUNTING .050 TO .248 -2 3-HOLE MOUNTING .050 TO .081 -3 1-HOLE MOUNTING .050

4、TO .248 1.0 TO 2.5 LB IDENTICAL TO -1, EXCEPT KEYWAY IS ROTATED 180 FIGURE1. Dimensions and configuration Continued Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25224H 3Inches mm Inches mm Inches mm .003 .08 .156 3.96 .840 21.34 .005 .13 .188 4.

5、77 .875 22.22 .008 .20 .240 6.10 .906 23.01 .016 .41 .248 6.30 1.062 26.97 .031 .79 .320 8.13 1.093 27.76 .032 .81 .469 11.91 1.547 39.29 .050 1.27 .475 12.06 1.635 41.53 .062 1.57 .516 13.11 1.812 46.02 .081 2.06 .688 17.47 1.830 46.48 .094 2.39 .719 18.26 2.125 53.98 .096 2.44 .750 19.05 NOTES: 1.

6、 Dimensions are in inches. 2. Unless otherwise specifies, tolerances are .016 on decimals. 3. For design feature purposed, this standard takes precedence over procurement documents referenced herein. 4. Referenced documents shall be of the issue in effect on date of invitations for bid. 5. Material:

7、 Plastic molded, red, number 11136, FED-STD- 595. Steel, commercial, shall be smooth and free from burrs. 6. Finish: Zinc plate, ASTM-B633 , type III , or cadmium plate, SAE-AMS-QQ-P-416, type III, with optional supplementary treatment per MIL-C-8514 or DOD-P-15328, black enamel, lusterless, color n

8、umber 37038 or semigloss, color number 27038, FED-STD- 595 or equivalent. REQUIREMENTS Guard shall remain in either the open or closed position Opening the guard shall not change position of the switch contacts. Toggle switch shown in position A. Closing the guard shall place the toggle in position

9、A. Referenced documents MIL-DTL-7703 SAE-AMS-QQ-P-416 DOD-P-15328D ASTM-B633 MIL-C-8514 FED-STD-595 Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking per

10、mitted without license from IHS-,-,-MS25224H 4Custodians: Preparing activity Army CR DLA CC Navy AS (Project 5930-2005-007) Air Force 11 DLA CC Review activities: Army AV Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-