DLA MS25216 REV C-2011 COVER TOP AND BOTTOM FUSELAGE LIGHTS.pdf

《DLA MS25216 REV C-2011 COVER TOP AND BOTTOM FUSELAGE LIGHTS.pdf》由会员分享，可在线阅读，更多相关《DLA MS25216 REV C-2011 COVER TOP AND BOTTOM FUSELAGE LIGHTS.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 6220 INCH-POUND MS25216C 9 August 2011 SUPERSEDING MS25216B 20 January 2006 DETAIL SPECIFICATION SHEET COVER, TOP AND BOTTOM FUSELAGE LIGHTS Inactive for new design after 20 January 2006. This specification is approved for use by all Departments and Agencies of the Department of Defense

2、. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-7989, “Covers, Light - Transmitting, for Aeronautical Lights, General Specification for“. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

3、,-,-MS25216C 2 NOTES: 1. All dimensions are in inches. 2. Unless otherwise specified, tolerances shall be: decimal dimensions: 0.016, angles: 1. 3. Break edges shall be 0.016 maximum. FIGURE 1. Cover. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M

4、S25216C 3 TABLE I. Light shield requirements. Dash no. Color 1Remarks 2 -1 Type II - Lunar white (clear) ND - WOS -2 ND - WS -3 D - WOS -4 D - WS -5 Type II - Red ND - WOS -6 ND - WS -7 D - WOS -8 D - WS -9 Type II - Green ND - WOS -10 ND - WS -11 D - WOS -12 D - WS -13 Type II - Yellow ND - WOS -14

5、 ND - WS -15 D - WOS -16 D-WS-17 Type I - Red ND - WOS -18 ND - WS -19 D - WOS -20 D - WS -21 Type I - Green ND - WOS -22 ND - WS -23 D - WOS -24 D - WS 1Type I, aviation colors, and type II, identification colors, shall be in accordance with SAE AS25050, “Colors, Aeronautical Lights and Lighting Eq

6、uipment, General Requirements for“.2Diffusing - D, Non-Diffusing - ND, Without Shield - WOS, and With Shield - WS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25216C 4 REQUIREMENTS: 1. A light shield of suitable dull opaque material or opaque a

7、luminum shall be applied to the inner surface in such manner as to render it capable of withstanding five hours continuous operation, installed on the intended lighting fixture, with an industry number 1047 lamp burning. Slightly raised lines may be molded on the glass to facilitate the application

8、of shielding: Masking to be applied before the diffusing enamel is applied. 2. The manufacturers trademark and the MS part number shall be marked on the cover. The markings shall be in such a location that they do not interfere with the light distribution. 3. All covers furnished under this specific

9、ation sheet shall be class B - heat resistant glass in accordance with MIL-DTL-7989, and conform to grade B transmission and brightness limits in accordance with SAE AS25050. NOTES: 1. In the event of a conflict between the text of this document and the references cited herein, the text of this docu

10、ment takes precedence. 2. Unless otherwise specified, issues of referenced documents are those in effect at time of solicitation. 3. The part or identifying number (PIN) to be used for fuselage light covers acquired to this specification sheet is created as follows: MS 25216 - XX Dash number (see ta

11、ble I) Specification number MS prefix Example of reference part number: MS25216-20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25216C 5 CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respe

12、ct to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Navy - AS Air Force - 99 DLA - GS DLA - GS2 (Project 6220-2011-002) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-