DLA MS24288 REV E-2005 INSERT ARRANGEMENTS ELECTRICAL CONNECTOR RACK AND PANEL《机架和小组电器连接器插入准备》.pdf

《DLA MS24288 REV E-2005 INSERT ARRANGEMENTS ELECTRICAL CONNECTOR RACK AND PANEL《机架和小组电器连接器插入准备》.pdf》由会员分享，可在线阅读，更多相关《DLA MS24288 REV E-2005 INSERT ARRANGEMENTS ELECTRICAL CONNECTOR RACK AND PANEL《机架和小组电器连接器插入准备》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDMS24288E 14 July 2005 SUPERSEDING MS24288D 20 July 1972 DETAIL SPECIFICATION SHEET INSERT ARRANGEMENTS, ELECTRICAL, CONNECTOR, RACK AND PANEL Inactive for new design after 8 June 1999. This specification is approved for use by all Departments and Agencies of the Department of Defense. The

2、requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26518. The Qualified Products List (QPL) associated with this inactive for new design specification will be maintained until acquisition of the product is no longer required, where upon the

3、specification and QPL will be canceled. REQUIREMENTS: Dimensions and configuration see figure 1. This is a design specification. Not to be used as a part number. Contact size/quantity Connector Arrangement designator 20 16 12 Coax Style PIN 1/ Style PIN A1 102 Pin MS24286RA1 Socket MS24285RA1 A1 102

4、 Pin MS24286HA1 Socket MS27399RA1 B1 52 Pin MS24286RB1 Socket MS24285RB1B1 52 Pin MS24286HB1 Socket MS27399RB1 A2 65 12 Pin MS24286RA2 Socket MS24285RA2 A2 65 12 Pin MS24286HA2 Socket MS27399RA2 A3 Pin MS24286RA3 Socket MS24285RA3 A3 Pin MS24286HA3 Socket MS27399RA3 B2 36 4 1 Pin MS24286RB2 Socket M

5、S24285RB2B2 36 4 1 Pin MS24286HB2 Socket MS27399RB2 B3 18 Pin MS24286RB3 Socket MS24285RB3B3 18 Pin MS24286HB3 Socket MS27399RB3 A4 33 9 Pin MS24286RA4 Socket MS24285RA4A4 33 9 Pin MS24286HA4 Socket MS27399RA4 A5 50 Pin MS24286RA5 Socket MS24285RA5 A5 50 Pin MS24286HA5 Socket MS27399RA5 B4 26 Pin MS

6、24286RB4 Socket MS24285RB4 1/ Part or Identifying Number (PIN). AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24288E 2 FIGURE 1. Shell size A1. FIGURE 1. Connector mating and mounting details. Provided by IHSNot for ResaleNo rep

7、roduction or networking permitted without license from IHS-,-,-MS24288E 3 Inches mm Inches mm .071 .125 .143 .214 .250 .286 .357 .375 .429 .500 .572 1.80 3.18 3.63 5.44 6.35 7.26 9.07 9.53 10.90 12.70 14.53 .643 .715 .786 .858 .929 1.001 1.072 1.144 1.215 1.287 1.358 1.430 16.33 18.16 19.96 21.79 23

8、.60 25.43 27.23 29.06 30.86 32.69 34.49 36.32 NOTES 1. Dimensions are in inches 2. Metric equivalents are given for information only. 3. Unless otherwise specified the tolerance is .002 (0.05 mm). 4. Rear face of pin insert shown socket insert opposite. 5. Contact identification shall be marked on r

9、ear surfaces. Characters shown are for rear face of pin insert. 6. The A2 contact shall be marked on face of the socket insert and the E2 contact shall be marked on the face of the pin insert. FIGURE 1. Connector mating and mounting details - Continued. Provided by IHSNot for ResaleNo reproduction o

10、r networking permitted without license from IHS-,-,-MS24288E 4 Inches mm .071 .125 .143 .214 .250 .286 .357 .375 .429 .500 .572 .643 .715 1.80 3.18 3.63 5.44 6.35 7.26 9.07 9.53 10.90 12.70 14.53 16.33 18.16 NOTES 1. Dimensions are in inches 2. Metric equivalents are given for information only. 3. U

11、nless otherwise specified the tolerance is .002 (0.05 mm). 4. Rear face of pin insert shown socket insert opposite. 5. Contact identification shall be marked on rear surfaces. Characters shown are for rear face of pin insert. 6. The A2 contact shall be marked on face of the socket insert and the E2

12、contact shall be marked on the face of the pin insert. FIGURE 2. Shell size B1.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24288E 5 12 size 12 contacts and 65 size 20 contacts FIGURE 3. Shell size A2. Provided by IHSNot for ResaleNo reproductio

13、n or networking permitted without license from IHS-,-,-MS24288E 6 Inches mm Inches mm .062 .078 .125 .161 .187 .207 .250 .312 .414 .437 .500 1.57 1.98 3.18 4.09 4.75 5.26 6.35 7.92 10.52 11.10 12.70 .643 .715 .786 .858 .929 1.001 1.072 1.144 1.215 1.287 1.358 1.430 16.33 18.16 19.96 21.79 23.60 25.4

14、3 27.23 29.06 30.86 32.69 34.49 36.32 NOTES 1. Dimensions are in inches 2. Metric equivalents are given for information only. 3. Unless otherwise specified the tolerance is .002 (0.05 mm). 4. Rear face of pin insert shown socket insert opposite. 5. Contact identification shall be marked on rear surf

15、aces. Characters shown are for rear face of pin insert. 6. The A2 contact shall be marked on face of the socket insert and the E2 contact shall be marked on the face of the pin insert. FIGURE 3. Shell size A2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

16、IHS-,-,-MS24288E 7 Inches mm .0715 .078 .113 .116 .125 .143 .2145 .232 .250 .286 .3575 .429 .464 .500 .5005 .572 .6435 .715 .7865 .858 .9295 1.001 1.0725 1.144 1.816 1.98 2.87 2.95 3.18 3.63 5.448 5.89 6.35 7.26 9.080 10.90 11.79 12.70 12.712 14.53 16.345 18.16 19.977 21.79 23.609 25.42 27.241 29.06

17、5 size 16 contacts and 82 size 20 contacts FIGURE 4. Shell size A3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24288E 8 NOTES 1. Dimensions are in inches 2. Metric equivalents are given for information only. 3. Unless otherwise specified the t

18、olerance is .002 (0.05 mm). 4. Rear face of pin insert shown socket insert opposite. 5. Contact identification shall be marked on rear surfaces. Characters shown are for rear face of pin insert. 6. The A2 contact shall be marked on face of the socket insert and the E2 contact shall be marked on the

19、face of the pin insert. FIGURE 4. Shell size A3 Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24288E 9 Inches mm Inches mm .113 .120 .125 .161 .188 .2145 .250 .286 2.87 3.05 3.18 4.09 4.78 5.448 6.35 7.26 .3575 .376 .429 .500 .5005 .57

20、2 .6435 .715 9.080 9.55 10.90 12.70 12.712 14.53 16.345 18.16 1 size coax contact, 4 size 16 contacts, and 36 size 20 contacts NOTES 1. Dimensions are in inches 2. Metric equivalents are given for information only. 3. Unless otherwise specified the tolerance is .002 (0.05 mm). 4. Rear face of pin in

21、sert shown socket insert opposite. 5. Contact identification shall be marked on rear surfaces. Characters shown are for rear face of pin insert. 6. The A2 contact shall be marked on face of the socket insert and the E2 contact shall be marked on the face of the pin insert. FIGURE 5. Shell size B2. P

22、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24288E 10 18 size 12 contacts Inches mm .040 .080 .160 .161 .200 .207 .280 .320 .400 .414 .440 .520 .560 .640 .680 1.02 2.03 4.06 4.10 5.08 5.26 7.11 8.13 10.16 10.52 11.18 13.21 14.22 16.26 17.27 NOTE

23、S 1. Dimensions are in inches 2. Metric equivalents are given for information only. 3. Unless otherwise specified the tolerance is .002 (0.05 mm). 4. Rear face of pin insert shown socket insert opposite. 5. Contact identification shall be marked on rear surfaces. Characters shown are for rear face o

24、f pin insert. 6. The A2 contact shall be marked on face of the socket insert and the C2 contact shall be marked on the face of the pin insert 7. Use SAE-AS39029/54, SAE-AS39029/55, or MS27399 as applicable. FIGURE 6. Shell size B3. Provided by IHSNot for ResaleNo reproduction or networking permitted

25、 without license from IHS-,-,-MS24288E 11 33 size 20 and 9 coax contacts Inches mm .125 .250 .500 .599 .750 1.000 1.144 1.287 1.2155 1.3585 1.430 3.18 6.35 12.70 15.21 19.05 25.4 29.06 32.69 30.873 34.506 36.32 NOTES 1. Dimensions are in inches 2. Metric equivalents are given for information only. 3

26、. Unless otherwise specified the tolerance is .002 (0.05 mm). 4. Rear face of pin insert shown socket insert opposite. 5. Contact identification shall be marked on rear surfaces. Characters shown are for rear face of pin insert. 6. The A2 contact shall be marked on face of the socket insert and the

27、E2 contact shall be marked on the face of the pin insert. 7. Use SAE-AS39029/54, SAE-AS39029/55, or MS27399 as applicable. FIGURE 7. Shell size A4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24288E 12 Inches mm .092 .1175 .184 .232 .235 .3525

28、.464 .470 .5875 .705 .8225 .940 1.0575 1.175 1.2925 1.410 2.34 2.984 4.67 5.89 5.97 8.95 11.79 11.94 14.92 17.91 20.89 23.88 26.86 29.85 32.830 35.81 59 size 16 contacts NOTES 1. Dimensions are in inches 2. Metric equivalents are given for information only. 3. Unless otherwise specified the toleranc

29、e is .002 (0.05 mm). 4. Rear face of pin insert shown socket insert opposite. 5. Contact identification shall be marked on rear surfaces. Characters shown are for rear face of pin insert. 6. The A2 contact shall be marked on face of the socket insert and the D2 contact shall be marked on the face of

30、 the pin insert. 7. Use SAE-AS39029/54, SAE-AS39029/55, or MS27399 as applicable. FIGURE 8. Shell size A5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24288E 13 26 size 16 contacts Inches mm .092 .113 .1175 .184 .232 .235 .3525 .464 .470 .5875

31、.705 2.34 2.87 2.98 4.67 5.89 5.97 8.95 11.79 11.94 14.923 19.05 NOTES 1. Dimensions are in inches 2. Metric equivalents are given for information only. 3. Unless otherwise specified the tolerance is .002 (0.05 mm). 4. Rear face of pin insert shown socket insert opposite. 5. Contact identification s

32、hall be marked on rear surfaces. Characters shown are for rear face of pin insert. 6. The A2 contact shall be marked on face of the socket insert and the C2 contact shall be marked on the face of the pin insert. FIGURE 9. Shell size B4. Provided by IHSNot for ResaleNo reproduction or networking perm

33、itted without license from IHS-,-,-MS24288E 14 Referenced documents: In addition to MIL-DTL-26518 this document references the following: MS27399 SAE-AS39029/54 SAE-AS39029/55 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previo

34、us issue due to the extent of the changes. CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 11 DLA - CC DLA - CC (Project 5935-4697-000) Review activities: Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-