DLA MS18151 REV K-2005 SWITCH TOGGLE ONE POLE SEALED TOGGLE《单极密封触发器开关》.pdf

《DLA MS18151 REV K-2005 SWITCH TOGGLE ONE POLE SEALED TOGGLE《单极密封触发器开关》.pdf》由会员分享，可在线阅读，更多相关《DLA MS18151 REV K-2005 SWITCH TOGGLE ONE POLE SEALED TOGGLE《单极密封触发器开关》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5930 INCH POUND MS18151K 17 October 2005 SUPERSEDING MS18151J 18 July 1991 DETAIL SPECIFICATION SHEET SWITCH, TOGGLE, ONE POLE, SEALED TOGGLE This specification is approved for use by all Departments and Agencies of the Department of Defense. The complete requirements for acquiring the

2、switch described herein shall consist of this specification and the latest issue of MIL-DTL-83731. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS18151K 2 FIGURE 1. Dimensions and configuration - Continued.

3、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS18151K 3 Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm .024 .034 .055 .057 .060 0.61 0.86 1.40 1.45 1.52 .067 .16 .19 .213 .223 1.70 4.1 4.8 5.41 5.66 .225 .228 .229 .230 .234 5.72 5.79

4、5.82 5.84 5.94 .235 .250 .252 .258 5.97 6.35 6.40 6.55 .266 .28 .33 .388 6.76 7.1 8.4 9.86 .408 .480 .688 .705 10.36 12.19 17.48 17.91 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for th

5、ree place decimals and .02 (0.5 mm) for two place decimals. 4. For hardware detail specifications, see appendix of MIL-DTL-83731. 5. Contour of switch optional provided maximum dimensions specified are not exceeded. 6. Referenced documents shall be of the issue in effect on date of invitation for bi

6、d. 7. For design feature purposes, this military specification takes precedence over acquisition documents referenced herein. FIGURE 1. Dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS18151K 4 REQUIREMENTS:

7、 All switches on this military specification are designed so that the movement of the switch mechanism is the same as that of the toggle lever. Switching action: Keying side - On, Center - None, Opposite side - On. TABLE I. Electrical ratings. 28 V dc 120 V dc 115 V ac 60 and 400 Hz RES IND LAMP 1.5

8、 A 0.5 A 0.5 A 0.1 A 0.1 A 0.1 A 1.0 A 0.5 A 0.5 A Strength of actuating lever pivot and lever stop: 12 pounds. Dielectric withstanding voltage: Initial: 1,000 V (Sea level), 400 V (altitude). After endurance tests: 600 V. Shock: Method II. Operating temperature range: -40C to +71C. Short circuit: M

9、ethod II. Weight: 0.010 pound maximum. Electrical Life at 65,000 ft altitude: 2,000 cycles. Military PIN: MS18151-1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS18151K 5 Referenced Documents: MIL-DTL-83731 ASTM-D5948 Marginal notations are not

10、used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing activity: Army - CR DLA CC Air Force - 11 Navy EC (Project 5930-1915-01) DLA - CC Review activities: Army - AV Navy AS Air Force - 99 NOTE: The activities listed above

11、 were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-