DLA MS9177 REV B-1988 SCREW MACHINE - CRES DOUBLE HEXAGON EXTENDED WASHER HEAD 138-40《0 138-40型垫圈顶部加长双重六边形防锈钢螺杆机》.pdf

《DLA MS9177 REV B-1988 SCREW MACHINE - CRES DOUBLE HEXAGON EXTENDED WASHER HEAD 138-40《0 138-40型垫圈顶部加长双重六边形防锈钢螺杆机》.pdf》由会员分享，可在线阅读，更多相关《DLA MS9177 REV B-1988 SCREW MACHINE - CRES DOUBLE HEXAGON EXTENDED WASHER HEAD 138-40《0 138-40型垫圈顶部加长双重六边形防锈钢螺杆机》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 - MS9177 REV B 53 W 9979912 0003043 W D- /7-23 PART NO. MS9177-02 MS9177-03 MS9177-O4 MS9177-05 MS9177-O6 MS9177-O7 MS9177-O8 HS9177-09 MS9177-10 WS9177-11 MS9177-12 O +.o08 - .O60 L .250 (a) -312 ia ) .375 .(a) .438 (a) .500 (a) .562 (a) .625 ia 1 a688 .125 .750 .iss .812 .250 .875 .319 e O .r 4J

2、n .r 4J V 0 .r m - 0 .375 .438 .500 .562 .625 .688 RD.(ucQAw 5305 .55 .57 .59 .61 .64 .66 MATERIAL IDENTIFICATION K TO FULLTHD - MAN U FACTU RERUS IDENTIFICATION (CEE REQUIREMENT 5) 350 SECTION THRU THREAD PROFILE FIGURE I TABLE I. OIMEHSIONS AND WEIGHTS 7iFFrm7 IJEIGHT L8/100 .30 . .32 .34 .37 .39

3、.41 .44 .46 .48 .50 .52 PART NO. MS9177-13 MS9177-14 MS9177-15 MS9177-16 MS9177-17 WS9177-18 liS9177-19 WS9177-20 HS9177-21 WS9177-22 (a) THREAD TO HEAD. MAXIMUM TWO IMPERFECT THREADS. i (b) B=PITCH DIAMETER (PD) - L - .938 1.000 1.062 1.125 1.188 1.250 1.312 1.375 1.436 1-500 - A INACTIVE FOR NEW D

4、ESIGN AFTER 31 DECEMBER 1963 B DEIOTES CtMGE .O15 -3!r R no01 I7O L: OPTIONAL SHAPE OF HEAD APPROX LB/lOO .750 .875 .73 A. YAW -AS )(hww rn SCREW, MACHINE-CRES DOUBLE HEXAGON, EXTENDED WASHER HEAD, .135-40 MILITARY STAWDA IkiGFGS I I 1 P I C I C ! 1 I i = -, Provided by IHSNot for ResaleNo reproduct

5、ion or networking permitted without license from IHS-,-,-FED. UlP CuLt 1 5305 REQUIREMENTS 1. MATERIAL: CORROSION AND HEAT RESISTANT STEEL PER AtiS 5732. 2. HAHUFACTURERS SPECIFICATION: WS 7478, 3. PART SUBJECT TO FLUORESCENT PENETRANT INSPECTION PER AHS 2645. 4. SURFACE ROUGHNESS: UNLESS OTHERWISE

6、SPECIFIED, 125 MICROINCHES PER ANSI 846.1. B 5. WUFACTURERS IDENTIFICATION: THE HANUFACTURERS SYMBOL PER MIL-STD-1291 (SEE FIG. 1 ) o SHALL BE HARKED ON THE BOLT HEAD (SEE FIG. I). OR LASER. MARKING MAY BE FORMED BY FOROING, STAMPING, MARKING SHALL BE RAISED OR INDENTED 0.010 INCH WAXIHUM. NOTES 1,

7、BREAK SHARP EDGES .003-,015 INCH UNLESS OTHERWISE SPECIFIED. 2. DIMENSIONS IN INCHES. 3. UNLESS OTHERWISE SPECIFIED: TOLERANCES: LINEAR DIMENSIONS: 1.010, ANGULAR: t5a. 4. DO NOT USE UNASSIGNED PART NUMBERS. HEREIN THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE, FOR AEROSPACE PROPULSION SYSTEMS. 5.

8、 IN THE EVENT OF A CONFLICT BETHEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED 6. THIS STANDARD HAS DEVELOPED COOPERATIVELY WITH THE SAE CWITTEE E-25, GENEWU. STANDARDS A. #N&M m MILITARY STANDARD SCREU, MACHINE-CRES DOUBLE HEXAGON, EXTEYOED WASHER HEAD, 138-40 MS 9177(AS) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-