DLA MIL-T-25186 A (3)-1982 TOILET AIRCRAFT CHEMICAL《航空器上化学制的马桶》.pdf

《DLA MIL-T-25186 A (3)-1982 TOILET AIRCRAFT CHEMICAL《航空器上化学制的马桶》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-T-25186 A (3)-1982 TOILET AIRCRAFT CHEMICAL《航空器上化学制的马桶》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、/- - MIL-T-251bA (3) 45 99999Ob 0214737 1 m MIL-T- 25 186A AMENDMNT 3 10 September 1982 SUPERSEDING AMENDMEIiT 2 17 March 1976 MILITARY SPECIFICATION TOILETS, AIRCRAFT, CHEMICAL This amendment forms a part of Military Specification MIL-T-25186A dated 5 July 1961, and is approved for use by all Depar

2、tments and Agencies of the Department of Defense. PAGE 1 2.1: Federal Specifications : Delete: “NN-P-515 - Plywood, Container Grade“ Add : “TT-E-489 - Enamel, Alkyd, Gloss, (For Ext Add : Dele te: Add : Delete: Add : De le te : Add : De le te : Add : ior and Inte ior Surfaces)“ “TT-P-1757 - Primer C

3、oating, Zinc Chromate, Low Moisture Sensitivity“ “PPP-B-591 - Boxes, Fiberboard, Wood-Cleated“ “PPP-B-591 - Boxes, Shipping, Fiberboard, Wood-Cleated“ “PPP-B-636 - Boxes, Fiberboard“ “PPP-B-636 - Box, Shipping, Fiberboard“ “PPP-B-665 - Boxes; Paper -Board, Metal Stayed (Includes Stayed Ma ter i al )

4、 I “PPP-B-665 - Boxes, Paperboard, Metal Edged and Components“ “PPP-B-676 - Boxes, Set-up Paper-board“ “PPP-B-676 - Boxes Setup“ ri U.S GOVERNMENT PRINTING OFFICE 1982-505-022/4724 FSC 4510 THIS DOCUMENT CONTAINS 3 PAGES. .F 1 of 3 o Provided by IHSNot for ResaleNo reproduction or networking permitt

5、ed without license from IHS-,-,-._ MIL-T-25186A AMENDMENT -3 . . L. Delete: “PPP-T-60“ - Tape, Pressure Sensitive Adhesive, Waterproof . for Packaging and Sealing“ ., . . Add: . . . “PPP-T-60 Tape, Packaging, Waterproof“ Military Specifications Dele te : - JAN-P-100 - Packaging and Packing for Overs

6、eas Shipment, II Gen er a 1 S p e c i f i c a t i on“ De le te : Add: “MIL-M-14 - Molding Plastic and Molded Plastic Parts, Thermo- “MIL-M-14 - Molding Plastic and Molded Parts, Thermosetting“ set t ing“ Add: “DOD-D-1000 - Drawing, Engineering And Associated List“ De le te: “MIL-R-3043 - Resin-Coati

7、ng, Permanent (For Internal Engine Add: “MIL-R-3043 - Resin Coating, Unpigmented, For Engine Components Parts II and Metal Parts“ Delete: “MXL-C-5541 - Chemical Films for Aluminum and Aluminum Alloys“ Add : “MIL-C-5541 - Chemical Conversion Coatings on Aluminum and Aluminum Alloys“ _. De le te : “MI

8、L-E-7729 -Enamel; Gloss, for Aircraft Use.“ PAGE 2 2.1: Military Specification: Delete: “MIL-P-8585 - Primer Coating, Zinc Chromate, Low-Moisture- Sensitivity“ De let e : “MIL-L-10547 - Liners , Case, Waterproof“ Add: . “MIL-L-10547 - Liner, Case, and Sheet, Overwrap, Water Vaporproof Or Waterproof

9、, Flexible“ I Delete: “MIL-D-70327 - Drawing, Engineering and Associated List“ Add: “MIL-STD-889 - Dissimilar Metals“ . Add : “MIL-STD-1186 - Cushioning, Anchoring, Bracing, Blocking, And De let e: Waterproofing, With Appropriate Test Methods “MS33586 - Metals -Definition of Dissimilar“ Federal Stan

10、dards : w 2 of 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-25LbA (3) 45 m 777770b 023Ll743 T m MIL-T-25186A AMENDMENT -3 3.1 Delete entire paragraph and add the following: Reclaimed Materials. Recycled and recovered raw material should be

11、 used to the maximum extent possible in lieu of virgin raw materials as long as these materials do not jeopardize the intended use and fully comply with all contract requirements. Materials used shall be free from defects which would affect the performance or maintainability of individual components

12、 of the overall assembly. 3.1.2 iine 5 delete “St andard MS33586“ and replace with “MIL-STD-889 3.3.2.2 Maximum weight for 6 gallon unit. Delete “10 pounds“ and substitute “15 pounds.“ PAGES 3, 4 and 5 Figures 1, 2 and 3. Add under tolerances: “Fractions t 1/32“. - PAGE 7 3.3.2.3 line 8 delete “MIL-

13、P-8585“ and replace with“TT-P-1757“. Line 10 delete “MIL-E-7729 type II or III“ and replace with “TT-E-489, type I, Class B.“ 3.4 lines 2 and 3 delete “in accordance with standard MIL-STD-130“ and replace with “as specified“. 3.6 line 5 delete “MIL-D-70327“ and replace with “DOD-D-1000“. PAGE 8 5.2.

14、1 lines 5, 6 and 7 delete “Plywood, when used, shall be type I or II, Class 2 of Specification NN-P-515.“ 5.3 lines 2, 3 and 6 delete “JAN-P-100 and replace with “MIL-STD-1186“. 5.4 lines 2 and 3 delete “in accordance with the requirements of Standard MIL-STD-129“ and replace with “as specified“. c CUSTODIAN: Navy - AS Air Force - 99 3 of 3 PREPARING ACTIVITY : Air Force -84 Project Number: 4510-018 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-