DLA MIL-S-29461 (1)-1992 SUIT CHEMICAL AND BIOLOGICAL PROTECTIVE (CARBON SPHERE)《化学和生物(碳球)套装》.pdf

《DLA MIL-S-29461 (1)-1992 SUIT CHEMICAL AND BIOLOGICAL PROTECTIVE (CARBON SPHERE)《化学和生物(碳球)套装》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-S-29461 (1)-1992 SUIT CHEMICAL AND BIOLOGICAL PROTECTIVE (CARBON SPHERE)《化学和生物(碳球)套装》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-294b1 (1) I Y9970b 2085355 94b I IINCH-POUNDJ MIL-S-29461 MILITARY SPECIFICATION SUIT, CHEMICAL AND BIOLOGICAL PROTECTIVE (CARBON SPHERE) This amendment forms a part of MIL-C-29461, dated 7 April 1992, and is approved for use by all Departments and Agencies of the Department of Defense. Page 2

2、 2.1.1 under “Specifications, Federal“ Delete: “PPP-3-636 - Box, Shipping, Fiberboard“ 2.1.1 under “Specifications, Military“ under “MIL-B-117“ Add: “MIL-B-13 1- Barrier Materials, Watervaporproof, Greaseproof Flexible, Heat Sealable. MILAT-3530 - Thread and Twine, Mildew Resistant or Water Repellan

3、t Treated. MIL-B-17757 - Box, Shipping, Fiberboard (Modular Sizes). After “MIL-C-43303 - Delete “MIL-T-43548 - Thread, Polyester, Cotton-Covered and Rayon Covered“ and add under Specifications, Federal the following: “A-A-50199 - Thread, Polyester Core, Cotton or Polyester-Covered“. Page 3 2.1.2 - U

4、nder “Drawings“ -Delete “1-6-102“ and substitute “2-6-102“. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A Approved for public release; distribution is unlimited. I of 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-294bL (I) II 0b 208535b 882 b

5、 MIL-S-29461 AMENDMENT-1 Page 4 3.3.1 - Delete in its entirety and substitute the following: “3.3.1 Outer shell. The camouflage printed and quarpel treated cotton cloth used for the outer shell of the Class 1 Suit shall conform to Type IV (Roll number 3476) of MIL-C-43468. The camouflage printed and

6、 quarpel treated cotton cloth used for the outer shell of the Class 2 Suit shall conform to Type V (Roll number 3300) of MIL-C-43468 (See 6.2)“. 3.3.2, Line 2 - At the end of paragraph, add the following: “The color of the lining shall be black.“ 3.3.4, line 1 - Delete “side“ and substitute “slide“.

7、 3.3.4, - At the end of paragraph, add the following: “The color and number for the slide fastener shall be Woodland Camouflage #7 Shade No.66519 for class 1 Suit, and Tan, Cable No.66516 for class 2 Suit“. 3.3.4.1, line 3 - At the end of paragraph, add the following: “The width of the slide fastene

8、r tape shall be 5/8 inch wide.“ Page 5 3.3.5, line 7 - Delete “pile“ and substitute “hook“. 3.3.6.1 line 4 - After “plastic“ add I, or equal“. 3.3.6.2, Line 2 - Delete “Natrick“ insert “Natick“ . 3.3.6.2, line 4 - After “plast.ic“ add I, or equal“. 3.3.8.1, line 3 -Delete “30,“. line 4 -Delete “MIL-

9、T-43548“ and substitute “A-A-50199“. Page 6 3.3.9.3 - Insert “INSTRUCTION LABEL*, in capital letters, above “Chemical and Bioloaical Protective Suit (Carbon Sphere)“. Y 3.3.9.3 - Instruction Label. At the end of 3, add the following: 2 of 11 Provided by IHSNot for ResaleNo reproduction or networking

10、 permitted without license from IHS-,-,-MIL-S-29461 AMENDMENT-1 Page 6 “4. These garments are items of outer wear and can be worn for up to 30 consecutive days. When exposed to chemical agent they will offer protection for at least 24 hours. At the end of 30 days or after 24 hours use in a chemical

11、environment the overgarments are to be replaced“. Page 10 After 3.7, add the following paragraph: “3.7.1 Fiaures. Figures are furnished for information only. To the extent of any inconsistencies between the figures and the written specification, the written specification shall govern“. Page 14 Opera

12、tion 3 - At the end of the operation add the following: “Note: No punches and/or drillholes permitted.“ Page 16 Table II, operation 9, line 11 - Delete “shellsleeve“ and substitute “shell sleeve“. Page 17 Table II, operation 10.a, line 2 - After “flap“ add “face to face“ . operation 10.b, line 4 - D

13、elete L/ 1/4“, and substitute “L/ 1/8 inch“. operation 11-b, line4 - Delete It?/ 1/4“, and Substitute “2 1/8 inch“. Page 24 Table II, operation 23.a, line 2 - After “flap“ add “right sides together“. 3 of 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

14、S-,-,-MIL-S-274bL (3) m 99999Ob 2085358 b55 MIL-S-29461 AMENDMENT-1 Page 25 Y Fable II, Operation 24b, line 2 - After “pleats“ delete “as the inarks are indicated on pattern“ and substitute “in accordance with pattern marks“. Page 26 i3peration 24d, line 2 - After “pocket“ add: “right sides together

15、 and. Page 29 Table II, operation 26., “Note:“, line 1 - Delete 22.b and 22.c“ land substitute “26.b and 26.c“. Page 31 Table II, operation 28.b line 10 - After “on“ add “for“. Page 32 Table II, operation 30, line 9 - After “on“ add I for“ . operation 31.a, line 2 - After “tab“ add “face to face“ .

16、Page 35 Table II, operation 34.b, line 2 - After “edges“ add “on outer shell“. operation 35.a, line 2 - After “edges“ add “on outer shell“. operation 35.b, line 9 - After “3/4“ delete remainder of sentence and substitute the following: “(2 1/4) inch“. operation 36.a, line 1 - After “bib“ delete “on“

17、. and substitute the following: “face side up on inside of“. Page 36 Table II, operation 37.a - After line 6, add the following sentence: “The bartack shall be 3/4 inch long and continuous, or as an alternate, two separate and aligned bartacks of 1/4 inch length may be used. I 4 of 11 Provided by IH

18、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29461 (1) I 999OL 2085359 591 S MIL-S-29461 AMENDMENT-1 Page 41 Table V - END ITEM VISUAL DEFECTS, “b.1“ - After “any hole“, insert, “exposed drill hole, or punch“. b. S.“Mends: -any mend up to 1/4 inch in diam

19、eter or length“ - Delete the “X“ under MINOR and move it under MAJOR. b. 2. “Mends: -any mend more than 1/4 inch in diameter or length“ - Delete the “X“ under MAJOR and move it under CRITICAL. c. -“Any cut, hole or tear“ - Delete the “X“ under MINOR and move it under MAJOR. c. -“Any missing yarn“ -

20、Delete the “X“ under MINOR and move it under MAJOR. Page 42 Table V - ENI) ITEM VISUAL DEFECTS, Under “Cleanness“ Spot or stain (grease, oil, ink) - Delete the “X“ under MINOR and move it under MAJOR. Under “ComDonents and assembly“ - Any assembly or operation not properly performed, unless otherwis

21、e classified herein. Delete the “X“ under MINOR and move it under MAJOR. Under “Seams and stitchinq, a.1.“ - Delete the “X“ under MINOR and move it under MAJOR. Page 44 Table V -END ITEM VISUAL DEFECTS, f. 1. - After “1 inch“ add “(excluding laminate lining c1oth)l. f. 2. - After “1 inch“ add “(excl

22、uding laminate lining cloth)“. f. 3. - After “or stitching“ add “(excluding laminate lining cloth) . Under “f. Stitch tension“ - After “f.3.“ add the following: “4. Loose tension on laminate lining cloth“. Add “X“ under MINOR. Page 47 Table V - END ITEM VISUAL DEFECTS, Under “Slide fastener, b.“ - D

23、elete the “X“ under MINOR and move it under MAJOR. 5 of 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29461 AMENDMENT-1 Y Page 47 Under “Slide fastener, c.“ - Delete the “X“ under MINOR and move it under MAJOR. Under “Slide fastener, d.“ -

24、 Delete the “X“ under MINOR and move it under MAJOR. Page 48 Under “Carqo pockets and flaps, a. - Delete the “X“ under MINOR and move it under MAJOR. Page 49 4.4.3.3, under DEFECTS - After last sentence add “Specified number of desiccant units not enclosed“. Page 51 4.4.7, line 2 - After “4 hours“,

25、add “at room temperature, l. 5.1.1, line 2 - After “and“ add “each component“. 5.1.1, line 3 - After “rectangle“, delete “.I and add “, each approximately 8 X 11 inches.“ Page 52 5.2.1 and 5.2.2 - Delete in their entirety and substitute the following: 5.2.1 Level A. Eight (8) suits (size x-large) or

26、 (10) suits (sizes small, medium and large) of one size only preserved as specified in 5.1.1 and 5.1.2, shall be packed in a fiberboard shipping container assembled, closed and reinforced to conform to Type CF, Class weather-resistant, Variety DW, style RSC-L, grade VZs, size 3A of MIL-B-17757. A li

27、ner conforming to type CF, Class Domestic, Variety DW, Grade V15c of MIL-B-17757 shall be placed inside carton. Packages shall be either packed flat and/or on end. All voids shall be filled with commercial grade kraft paper. The shipping container shall be sealed using glue. To accommodate the last

28、shipment at the end of the contract, less than full cartons and pallets are acceptable. 6 of 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29461 AMENDMENT-1 5.2.2 Level B. Eight (8) suits (size x-large) or (10) suits (sizes small, medium a

29、nd large) of one size only, packaged as specified, shall be packed in a fiberboard shipping container assembled and closed in accordance with MIL-B-17757. The container shall be size 3A, style RSC-L, Type CF, Class Domestic, Variety DW, Grade 275 of MIL-B-17757. A liner conforming to Type CF, Class

30、Domestic, Variety DW, Grade 275 of MIL-B-17757 shall be placed inside carton. Packages shall be either packed flat and/or on end. All voids shall be filled with commercial grade kraft paper. The shipping container shall be sealed using glue. To accommodate the last shipment at the end of the contrac

31、t, less than full cartons and pallets are acceptable. Page 53 5.3.4 - Delete in its entirety. 5.3.5 - Delete in its entirety. Add figures 1-4, following page 55. Custodian: MC Review Activity: MC USK Activity: MC Preparing Activity: (Project No 8415-N859) DLA-CT 7 of 11 Provided by IHSNot for Resale

32、No reproduction or networking permitted without license from IHS-,-,-MIL-S-29461 (1) I 9999906 2085362 086 MIL-S-29461 AMENDMENT-1 , I FIG1 Suit, Chemical and Biological Protective (Carbon Sphere) (COAT I 8 of 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

33、om IHS-,-,-MIL-S-29461 (1) I 99995Ob 20853b3 TL2 6 MIL-S-29461 Amendment-1 CONSTRUCTION DETAILS: SIDE VIEW (LEFT) ( COAT ) 1 - SEWN EXELET (HOOD h BOITOM OF SUIT TOP) 2 - RUBBER CORD (DRAWSTRING) 3 - FWKET HAS PILE TAFT (FLAP HAS HOOK TAPE) 4 - TAB HWK Note: The Measurements on this Figure are based

34、 on a size Aium suit. 5 - SLIDE FASTENER 6 - SLEEVE (WITH ELBOW PATCH) 7 - TAB HOOK & PILE FASTENER 8 - HOOD CWER PANEL 9 - HOOD SIDE PANEL SIZES: A - 8 1/2 INCHES B - 9 1/2 INCHES (ELBOW PATCH) c-7 INCHES (%WAL SLEEVE LE“ = 25“) I D-3 INCHES 7 2/8“) FIG2 Suit, Chemical and Biological Protective (Ca

35、rbon Sphere) 9 of 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-2W q-1 CONSTRUCTION DETAILS: FRONT VIEW (TROUSERS) STITCH EDGE - Note: The basurements on this Figure are based on a size mediun suit. GUSSET IST TAB (PILE) CARGO POCKET FLAP

36、CARGO POCKET KNEE PATCH LEG TAB (TAB HOOK) LEG TAB (PILE) Y FIG3 Suit, Chemical and biological Protective (Carbon Sphere) Figure 3 10 of 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. HI GS-!%61 “WNT-1 CONSTRUCTION DETAILS: CACK VIEW , (TROUSER

37、S) A - BIB (7 INCHES) B - 11 INCHES C - CARGO POCKET (10-1/2”) D - 20 INCHES E - 2-1/2 INCHES G - WAIST TAB (TAB HOOK) F - LEG TAB (PILE) I- SUSPENDER(S), J - BAR TACK(S) - GUSSET STRAP TAPE STITCH EDGE The Measurements Figure are based mediun suit. on this on a size FIG4 Suit, Chemical and Biological Protective (Carbon Sphere) Figure 4 11 of 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-