DLA MIL-S-16032 M-1987 SWITCHES AND DETECTORS SHIPBOARD ALARM SYSTEMS《舰载警报系统的开关器和检测器》.pdf

《DLA MIL-S-16032 M-1987 SWITCHES AND DETECTORS SHIPBOARD ALARM SYSTEMS《舰载警报系统的开关器和检测器》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-S-16032 M-1987 SWITCHES AND DETECTORS SHIPBOARD ALARM SYSTEMS《舰载警报系统的开关器和检测器》.pdf（58页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-16032M(SH)a71a13a1529 June 1987SUPERSEDINGMIL-s-16032L(SH)19 January 1981(See 6.9)MILITARY SPECIFICATIONSWITCHES AND OETECTORS , SHIPBOARD ALAR!ISYSTENSThis specification is approved for use within the Naval Sea SystemsConmand , Department of the Navy, and is available for use by altDepartment

2、s and Agencies of the Department of Defense.1,1. SCOPE1.1 g. This specification covers pressure, temperature, thermostatic,door, water, liquid level, liquid flow, and airflow switches, and single-purpose(smoke or combustion gas) detectors and flame detectors used on Naval ships forvisual and audible

3、 alarm systems (that is, systems utilizing indicator lights,sirens, bells, alarm panels) in conjunction with steam or air systems, dieselengines, turbines, auxiliary machinery. This specification is not intended tocover thermostatic or pressure operated switches used as operating controls ,unless In

4、terconnected with an alarm system or specifically required by otherprimary equipment specifications.1.2 Classification. Types of switches and detectors shall be designatedin the forms, as specified (see 3.2.1 through 3.2.1.5 and 6.2.1). (See figures1, 2, and 3 for schematic representation of type de

5、signation. )2. APPLICABLE OOCUMENTS2.1 Government documents.2.1.1 Specifications, standards, and hsndbooks. The following specifica-tions, standards, and handbooks form a part of this specification to the extentspecified herein. Unless otherwise specified, the issues of these documentsshall be those

6、 listed in the issue of the Department of Defense Index ofSpecifications and Standards (DoDISS) and supplement thereto, cited in thesolicitation.a71Beneficial comments (recommendations , additions, deletions) and any pertinentdata which a75ay be of use in improving this document should be addressed

7、to:Commander, Naval Sea Systems Command, SEA 55Z3, Department of the Navy,Washington, OC 20362-5101 by using the self-addressed Standardization OocumentImprovement Proposal (DO Form 1426) appearing at the end of this document orby letter.AMSC N/ADISTRIBUTION STATEMENT AFSC 5930Approved for public re

8、lease; distribution unlimitedProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-16032M(SH)SPECIFICATIONSFEDERALQ*B-61 3QQ-B-626QQ-B-637QQ-B-639QQ-B-750QQ-C-530QQ-C-533QQ-S-763QQ-S-766uU-P-268PPP-C-850PPP-C-1 120MILITARYIIL-R-26MIL-R-26/5MIL-S-901M

9、IL-F-1 183MIL-E-2036MIL-D-2940MIL-R-6130MIL-S-8805Brass. Leaded and Non-Leaded : Flat Products (Plate.Bar,Sheet, and Strip). -Brass, Leaded and Non-Leaded: Rod, Shapes,Forgings, and Flat Products with Finished Edges(Bar and Strip).Brass, Naval: Rod, Wire, Shapes, Porgings , andFlat Products with Fin

10、ished Edges (Bar, FlatWire , and Strip).Brass, Naval: Flat Products (Plate, Bar, Sheet,and Strip).Bronze, Phosphor; Bar, Plate, Rod, Sheet, Strip,Flat Wire, and Structural and Special ShapedSections.Copper-Beryllium Alloy Bars, Rods, and Wire (CopperAlloy Numbers 172 and 173).Copper-Beryllium Alloy

11、Strip (Copper Alloy Numbers170 and 172).Steel Bars, Wire, Shapes, and Forgings , CorrosionResisting.Steel Plates, Sheets, and Strip - Corrosion-Resisting.Paper, Kraft, Wrapping.Cushioning Material, Polystyrene Expanded, Resilient(For Packaging Use).Cushioning Material, Uncompressed Bound Fiber forPa

12、ckaging. a71Resistors, Fixed, Wire-Wound (Power Type), GeneralSpecification for.Resistors, Fixed, Wire-Wound (Power Type) , StylesRW70, RW74, RW78, and RW79.Shock Tests, H.I. (High-Impact ); Shipboard Machinery,Equipment and Systems, Requirements for.Fittings, Tube, Cast Bronze, Silver-Brazing.Enclo

13、sures for Electric and Electronic Equipment,Naval Shipboard.Dampeners, Fluid Pressure, Gage Protection.Rubber. Cellular, Chemically Blown.- Switches and Switch Assemblies , Sensitive and Push,(Snap Action) General Specification for.MIL-M-103O4 - Meters , Electrical Indicating, Panel Type,Kuggedized,

14、 General Specification for.MIL-A-15303 - Audible Signals: Alarms, Bells, Buzzers, Horns ,Sirens, and Electronic Shipboard.MIL-E-16400 - Electronic, Interior Communication and NavigationEquipment, Naval Ship and Shore: GeneralSpecification for.Ia712Provided by IHSNot for ResaleNo reproduction or netw

15、orking permitted without license from IHS-,-,-MIL-S-16032M(SH)MILITARY (Continued)MIL-A-17196 - Alarm Switchboards, Alarm Panels, Signal Units,and Special Alarm Connection Box, Naval Ship-board.MIL-E-17555 - Electronic and Electrical Equipment, Accessories,and Repair Parts; Packaging and Packing of.

16、MIL-F-18866 - Fittinga, Hydraulic Tube, Flared, 37 Degreeand Flareless; Steel.MIL-S-19622 - Stuffing Tubes (Nylon) General Specification.MIL-S-19622/l - Stuffing Tube Straight, Nylon.MIL-R-20092 - Rubber Sheets and Molded Shapes, Cellular,Synthetic, Open .Cell (Foamed Latex).MIL-S-24235 - Stuffing T

17、ubes, Metal, and Packing hsembliesfor Electric Cables, Ceneral Specificationfor.MIL-s-24235/14 - Stuffing Tube for Sheet Metal Enclosures.MIL-s-24236 - Switches, Thermostatic, (Metallic and Bimetallic)General Specification for.MIL-S-24236/l - Switches , Thermostatic, (Bimetallic) , Subminia-ture, Ty

18、pe 1, Hermetically Sealed, Single Pole,Single Throw (SPST), 5 Amperes.HIL-T-24388 - Thermocouples and Resistance Temperature Elements(Naval Shipboard Use).MIL-c-24643 - Cable and Cord Electrical, Low Smoke, forShipboard Use, General Specification for.MIL-C-24643/2 - Cord, Electrical, 300 Volts, Type

19、s LSDCOP andLSTCOP.MIL-c-24643/7 - Cable, Electrical, 600 Volts, Type LSMHOF.MIL-C-24643/12 - Cable, Electrical, 300 Volts, Type LSTTOP.MIL-R-39007 - Resistors, Fixed, Wire-Wound (Power Type),Established Reliability, General Specificationfor.MIL-R-39007/6 - Resistors, Fixed, Wire-Wound (Power Type),

20、Style RWR74.STANDARDSMILITARYMIL-STD-105 - Sampling Procedures and Tables for Inspectionby Attributes.MIL-STD-108 - Definitions of and Basic Requirements forEnclosures for Electric and Electronic Equip-ment.MIL-sTD-167-1 - Mechanical Vibrations of Shipboard Equipment(Type I - Environmental and Type

21、11 - InternallyExcited).MIL-sTD-278 - Welding and Casting Standard.MIL-STD-46 1 - Electromagnetic Emission and SusceptibilityRequirements for the Control of Electro-magnetic Interference.MIL-sTD-462 - Electromagnetic Interference Characteristics ,Measurement of.a713Provided by IHSNot for ResaleNo re

22、production or networking permitted without license from IHS-,-,-MIL-s-16032M(SH)IMILITARY (Centinued)MIL-STD-785 -DOOSTD-1399 , -Section 300HAND800KNILITARYMIL-HDBK-21 7 -Reliability Program for Systems and EquipmentDevelopment and Production.Interface Standard for Shipboard Systems Electric a71Powe

23、r, Alternating Current. (Metric)Reliability Prediction of Electronic Equipment.2.1.2 Drawings and publication. The following drawings and publicationform a part of this specification to the extent specified herein. Unlessotherwise specified, the issues shall be those in effect on the date of thesoli

24、citation.oRAWINGSNAVAL SEA SYSTEMS COMMAND (NAVSEA)401-1973965 - Switch, Door, Type IC/DM-l-O.803-74081 - Magazine Sprinkling Alarm Equipment - WaterSwitch - P.P., Symbol 2977.803-1197118 - Switch, Thermostatic (Mercurial), Types IC/J-105,IC/J-125, IC/J-150, Symbols 2805.1, 2806.1 and2807.1.804-1385

25、850 - Piping, Gage, For All Service.804-1853145 - System, Airflow Indicator and Alarm, 115 Volts,AC, 60 Cycles, Circuit HF.PUBLICATIONNAVAL SEA SYSTEMS COMMAND (NAVSEA)0900-LP-001-7000 - Fabrication and Inspection of Brazed PipingSystems.(Copies of specifications, standards, handbooks, drawings and

26、publicationsrequired by contractors in connection with specific acquisition functions shouldbe obtained from the contracting activity or as directed by the contractingactivity. )2.2 Other publications. The following documents form a part of this speci-fication to the extent specified herein. Unless

27、otherwise specified, the issuesof the documents which are DoD adopted shall be those listed in the issue of theDoDISS specified in the solicitation. Unless otherwise specified, the issues ofdocuments not listed in the DoDISS shall be the issue of the non-Governtientdocu-ments which is current on the

28、 date of the solicitation.AMXRICAN NATIOhXL STANDARDS INSTITUTE, INC. (ANSI)B16.5 - Steel Pipe Flanges, Flanged Valves, and Fittings.(Application for copies should be addressed toStandards Institute, Inc., 1430 Broadway, New York,4the American NationalNY 10018.)Provided by IHSNot for ResaleNo reprod

29、uction or networking permitted without license from IHS-,-,-MIL-S-16032M(SN)a71cooE OF FEOERAL REGULATIONS (CFR)Title 10, Chapter 1, Part 30 - Rules of General Applicability toLicensing of Byproduct Naterial.(Application for copies should be addressed to the Superintendent ofOocuments, U.S. Governme

30、nt Printing Office, Washington, DC 20402.)UNDERWRITERS LABORATORIES (UL)UL 167 - Combustion Products Type of Smoke 13etector.(Application for copies should be addressed to the Underwriters Laboratories, Inc., 207 East Ohio Street, Chicago, IL 60611.)(Nongovermnent standards a“d other publications ar

31、e normally svailablefrom the organizations which prepare or which distribute the documents. Thesedocuments also may be available in or through libraries or other informationalservices. )2.3 Order of precedence. In the event of a conflict between the text ofthis specification and the references cited

32、 herein (except for associated detailspecifications, specification sheets or MS standards), the text of this speci-fication shall take precedence. Nothing in this specification, however, shallsupersede applicable laws and regulations unless a specific exemption has beenobtained.3. REQUIREMENTS3.1 Qu

33、alification for types IC/L, N, R, RH, RL, DM, J, W, FS, and ASE only.The switches and detectors furnished under this specification shall be productswhich are authorized by the qualifying activity for listing on the applicablequalified products list at the time set for opening of bids (see 4.3 and 6.

34、4).3.1.1 First article inspection for types IC/F, IC/CC and IC/CGD only.When specified in the contract or purchase order, a sample shall be subjectedto first article inspection (see 4.3.3 and 6.5).3.2 General features. The switches and detectors shall be in accordancewith the following paragraphs of

35、 MIL-E-16400 in addition to the requirementsspecified herein. (Whenever a requirement of MIL-E-16400 conflicts with arequirement of this specification, the requirementgovern) :ScopeDefinitionsNaterialsParts, materials and processesFungus-inert a75aterialsFlammable materialsArc-resistant materialsSaf

36、ety (personnel hazard)Lightweight metal (aluminum alloy)Unacceptable materialsof this specification shallLProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-xIL-S-16032M( SH)Nonferrous metalsZincSprings (material)Insulating material, electricalEncapsula

37、tion and embedmentGlassLubricantsPaintingCorrosion protectionlcorrosion-resisting treatmentsFastener hardwareGaskets and sealsShaft locking devicesCapacitorsResistors, variables , wire-wound precisionTransformers , inductors , and coilsRelaysInsulating materials, electricalSwitches and associated ha

38、rdwareEnclosuresEnclosure-degree of (see 3.3.1, 3.4.1, 3.7.1.3(c), 3.8.6, 3.9, 3.11,and 3.12)Equipment mountingRigidityThrough boltingCable entrance (see 3.2.7)Thermal designRounded corners and edgesStructural weldingEnvironmental service conditionsSalt fog sprayShock, vibration inclination (vital v

39、ibration test required) (see4.9.2 and 4.9.17)Electrical design and constructionShipboard alternating current (at) power service (normal powersupply 115 volts, SO hertz (Hz), single phase ac) (see 3.2.3)Safety (personnel hazard)Bonding and groundingSolderingMounting of partsModular constructionTermin

40、als (terninal boards and strips, binding posts and lugs)Internal wiring and cablingConductor identification terminal end identificationDielectric withstanding voltageElectrical creepage and clearance distancesInterchangeabilityWorkmanship6Provided by IHSNot for ResaleNo reproduction or networking pe

41、rmitted without license from IHS-,-,-MIL-S-16032M(SH)3.2.1 Basic indicator. Basic indicator for this equipment shall be IC/.3.2.1.1 Type of operation. Type of operation shall be designated by aletter as shown in table I.SymbolFLNRRHRLDMJwFSASECGCGDTABLE I. Type of operation.Type of operationFlamePre

42、ssure or vacuum or bothTemperatureLiquid levelLiquid level, heavy duty, special purposeLiquid level, to actuate in 1/2 to 3/4 inchof liquid “rise”DoorThermostatic (mercurial or nonmercurial)WaterLiquid flowAirflowSingle-purpose combustion gas detectorSingle-purpose combustion gas detectorfor ducts3.

43、2.1.2 Ranee. Ranze shall be indicaced by a number as shown in tablesII, III, and I= (Ranges-shown are minimum; swiches having a wider range areacceptable. ) Table 11 ahowa pressure switches commonly in use and should notbe considered restrictive for requirements other than those ranges and differ-en

44、tials listed therein. Temperature ranges shown in table 111 shall not beconsidered restrictive. Table IV indicates liquid flow switches, port sizesand flow setting available, but should not be considered restrictive. Table Vshows liquid level switches indicating whether for single level or multiplel

45、evel detection type. Table VI shows door switches and indicates the mechanicalrange features. Table VII shows mercurial chermoatatic switches and indicatesthe operating points, but shall not be considered restrictive. Table VIII showsairflow switches and indicates the operating points. Table IX show

46、s the smokeaenaing portion of the single purpose detector and indicates operating levels.!0Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Symbol1234567fMIL-S-16032M(SH)TABLE 11. Sange for eure wtce.lIAdjustmentoperatingworking:g:ye15 to 28inchesmerc

47、uryabsolute1 to15 lb/in215 to50 lb/in250 to100 lb/in225 to50 lb/in220 to80 lb/in21000 to5000 lb/in2Maxi-mumproofpres-sure.?llb/in25801252001252005100AlMxximumallowablevariationfrom set-ting ofoperatingpressurePlus orminus1 inch1/2 lb/in22 lb/in24 lb/in22 lb/in22 lb/in240 lb/in2/Maximumdifferential2

48、inches1-1/4 lblin25 lb/in210 lb/in225 lb/in210 lb/in2100 to200 lb/in21Connectionforpressuresupply1/ Unless otherwise specified, for differential pressure switches , the rangesto be specified in 6.2.1 are the operating differential Pressure range(decreasing or increasing differential prssure) and the

49、 resetting dffer-ential pressure range, both ranges relative to gauge pressure.1 Unless otherwise specified, is in gauge pressure. Maximum proof pressureis upper pressure at which performance of switch in the operating rangewill not be disturbed and shall exceed maximum operating pressure.AI Unless otherwise specified in the contract or order, type of connectionshall be in accordance with Drawing 804-138580, that is, a mechan