DLA MIL-S-13192 P (1)-1994 SHOES MEN-S DRESS OXFORD《牛津布服装男鞋》.pdf

《DLA MIL-S-13192 P (1)-1994 SHOES MEN-S DRESS OXFORD《牛津布服装男鞋》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-S-13192 P (1)-1994 SHOES MEN-S DRESS OXFORD《牛津布服装男鞋》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、I INCH POUNDI MIL-S-13192P AMENDMENT 1 14 October 1994 MILITARY SPECIFICATION SHOES, MENS, DRESS, OXFORD This amendment forms a part of MIL-S-l3192P, dated 30 June 1988, and is approved for use by all departments and agencies of the Department of Defense. PAGE 9 Add as new paragraph 3.3.6.1 the foll

2、owing: “As a alternate when automated lasting is used, a water activated laminated box toe may be used. 3.3.6.1 Laminated box toe/water activated. Box toe shall be laminate of an alloyed ionomer resin of at least 60 percent virgin ionomer (surlyn) laminated with woven fabric on both sides with parti

3、ally water soluble acrylic adhesive coating laminated over the fabric. The combined thickness of this laminated layer shall be .O38 inches + .O075 inches.“. PAGE 11 * 3.3.8.1.2, Line 3: Delete “47“ and substitute “43“. AMSC N/A 1 Of 4 FSC 8430 DISTRIBUTION STATEMENT A. Approved for public release; d

4、istribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-13192P AMENDMENT 1 PAGE 17 * Table XI, opposite “Quarter Lining“ (two places), under “4-1/2 oz. leather“: Delete “3/8 +/- 1/8“. Under “3-3/4 oz. Leather“: Delete “* . Und

5、er “3-1/2 oz. Leather“: Delete and substitute 113/8 +/- 1/8“. * Table XI, opposite “Quarter lining - Long and short piece top, and vamp line“, under “2-1/2 oz. Leather“: Delete “*“ and subst-itute “1/4 +/- 1/32“. PAGE 22 Add as new paragraph 3.7.20.1, the following: 3.7.20.1 Fiberqlass shanks. When

6、the alternate fiberglass shank specified in 3.3.8.2 is used, the toe end of the shank shall be positioned approximately 1/2 inch rearward of the ball line with the heel end of the shank extended into the heel seat area. The shank shall be cut, positioned, shaped, bonded, and cured during the same op

7、eration using automatic shank setting equipment. Bottom filler shall be applied starting at the toe end of the shank and working back thru the heel seat area filling all. PAGE 31 Add as new paragraph 4.4.2.1, the following: Under paragraph 4.4.2.1, after last defect listing (Cluster of veins ., inse

8、rt the following: “Cavities around the shank, coarseness of hair cell pattern (type III cattlehide sides only) greater than standard sample “and“ embossed pattern used on calfskin or kip“. PAGE 33 Table XV, under “Defects examined before bottom fillinq Add the following defects: “Hair cell pattern n

9、ot uniform affecting the appearance - Minor“. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.A.- -. MIL-S-13192P (1) m 999990b 1995429 957 = MIL-S-13192P AMENDMENT 1 PAGE 36 Table XVI, under “Examine“ column: Delete “Kip (type II and cattlehide t

10、ype III) “and substitute “Kip (type II) I. Under “Examine“ column, after defect for “Kip (type II). Add the following examinations: “Cattlehide (type III surface not embossed) - Not burnished full grain smooth finish major“and“catt1ehide (type III - embossed) haircell pattern exceeds coarseness of s

11、tandard sample - “Major Defect“. Standard sample oly for: Maximum allowable coarseness of embossed hair cell pattern, roll # 3448 is applicable and is available from DPSC-FQP. NOTES : Contractors will not be required to perforin intermediate examinations specified in paragraph 4.2.2.2. however, cont

12、ractors will be required, as part of their inspection system, to establish stations for the examinations of intermediate product for the characteristics listed in the aforementioned paragraph, as well as for additional defects which may be detectable. the contractor shall reattach all heel pads that

13、 were removed by the government in the performance of verification inspection. The Government reserves the right to perform the intermediate examination in accordance with specification requirements and to reject any lots found to be nonconforming. Add the following sentence to end of paragraph 4.4.

14、1 in specification MIL-S-13192P. A certificate of compliance shall be submitted and will be accepted for the stated testing and inspection requirement contained in the component specification for the following components: Component/Paraqraph #. Heel bases 3.3.10.1 Welting . 3.3.1.5 Laces . 3.3.15 Up

15、per thread 3.3.5.1 Quarter topcord . 3.3.4.4 Bottom filling . 3.3.7 Twill toe lining 3.3.4.3 Thread, sole stitch . 3.3.5.2 Thread, inseaming . 3.3.5.3 Wool felt. 3.3.4.5 In addition to the certificate of compliance, a laboratory test report shall be provided with each component lot/shipment from eac

16、h supplier for prime contractor records when deemed necessary on all components covered by a “certificate of compliance“. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-13192P (1) W 99999Ob 1995430 b79 W MIL-S-13192P AMENDMENT 1 NOTES : * 4.

17、4. Quality conformance inspection * NOTES: a. b. C. All sampling acceptance number are reduced by one-third where the acceptance number is equal to or greater than three (3). For example, where the original MIL-STD-105 sampling acceptance number is three (3), the new acceptance number is two (2). Fo

18、r a point system if acceptance number was previously 150, the new acceptance number is 100. A sampling acceptance number of two (2) is reduced to one (1). A sampling acceptance number of one (1) remains the same. Custodians: Army - GL Navy - NU Air Force - 11 Review Activities: Army - MD Navy - MC Air Force - 99, 82 Preparing Activity: DLA - CT Project No. (8430-0432) c -Y User Activity: Air Force - 45 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-