DLA MIL-PRF-6106 20 D-2011 RELAYS ELECTROMAGNETIC MAGNETIC LATCH 25 AMPERES SPDT HERMETICALLY SEALED.pdf
《DLA MIL-PRF-6106 20 D-2011 RELAYS ELECTROMAGNETIC MAGNETIC LATCH 25 AMPERES SPDT HERMETICALLY SEALED.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-PRF-6106 20 D-2011 RELAYS ELECTROMAGNETIC MAGNETIC LATCH 25 AMPERES SPDT HERMETICALLY SEALED.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 5945 INCH-POUND MIL-PRF-6106/20D 1 November 2011 SUPERSEDING MIL-PRF-6106/20C 10 November 2000 PERFORMANCE SPECIFICATION SHEET RELAYS, ELECTROMAGNETIC, MAGNETIC LATCH, 25 AMPERES, SPDT, HERMETICALLY SEALED Inactive for new design after 15 November 2002. No superseding document. This spe
2、cification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and MIL-PRF-6106 FIGURE 1. Relay, outline drawing.Provided by IHSNot for ResaleNo reproduction or networking perm
3、itted without license from IHS-,-,-MIL-PRF-6106/20D 2 FIGURE 1. Relay, outline drawing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/20D 3 Inches mm Inches mm Inches mm .001 0.03 .156 3.96 .525 13.34 .002 0.05 .172 4.37 .5
4、62 14.27 .003 0.08 .234 5.94 .625 15.88 .005 0.13 .250 6.35 .630 16.00 .020 0.51 .270 6.86 1.010 25.65 .040 1.02 .281 7.14 1.025 26.04 .050 1.27 .300 7.62 1.062 26.97 .062 1.57 .375 9.52 1.396 35.46 .093 2.36 .432 10.97 1.406 35.71 .100 2.54 .485 12.32 1.446 36.73 .150 3.61 .500 12.70 1.718 43.64 NO
5、TES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (0.25 mm). 4. Terminal numbers need not appear on the relay header provided there is affixed to the relay a suitable legible circuit diagram that identifie
6、s each terminal location specified. 5. Note to observe polarity must appear on relays. 6. Hook terminals will accept one No. 12 AWG stranded wire. 7. Socket pin terminals shall provide the operational, environmental, and interface characteristics to provide a reliable interconnect to gold-plated con
7、tacts. Terminals shall be gold plated. Gold plating of the polarizing pin is optional. One system for gold plating that may be used is ASTM B488, type 3, class 1.25 with a nickel underplate of 50 to 150 microinches thick. The gold plating system shall enable the product to meet the performance requi
8、rements of this specification and shall be approved by the qualifying activity. 8. Gasket shall provide a reliable seal between the relay and mating socket that will meet the environmental, operational, and interface requirements of the relay with the mating socket. The gasket shall have shore hardn
9、ess 20 5, thickness .050 .005. Gasket material according to SAE-AMS 3332 has been considered acceptable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/20D 4 REQUIREMENTS Weight: 0.10 pound maximum. Temperature range 1/: -70C to +125C.
10、Maximum altitude-rating: 80,000 feet. Shock g-level: 200 g. Duration: 6 milliseconds. Maximum duration contact opening: 10 microseconds. Vibration-sinusoidal: G-level: 30 g. Frequency range: 10-3,000 Hz. Vibration-random: Applicable specification: MIL-STD-202, method 214, test condition IG. Duration
11、: 15 minutes, each plane. Strength of terminals and mounting studs: Applicable. Terminal solderability: Applicable to solder pin and solder hook terminals only. Acceleration: 15 g. Insulation resistance, initial: 100 megohms. Afterlife or environmental tests: 50 megohms. Dielectric withstanding volt
12、age (sea level): Initial After life tests Coil to case and coil to coil 1,000 V rms 1,000 V rms All other points 1,250 V rms 1,000 V rms Dielectric withstanding voltage (altitude) 2/: 80,000 feet 300,000 feet Coil to case and coil to coil 250 V rms 500 V rms All other points 350 V rms 500 V rms _ 1/
13、 For full rated load, maximum temperature, and altitude, use no. 12 wire or larger. Solder hook relays will be mounted to limit mounting bracket temperature to 135C. 2/ Dielectric withstanding voltage rating may be improved by suitable insulation of terminals and wiring after installation. Plug in r
14、elays, with suitable gasket compressed, will have dielectric withstanding voltage capabilities at 80,000 feet over 500 V rms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/20D 5 Maximum contact drop, initial: 0.150 volt. After life tes
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILPRF610620D2011RELAYSELECTROMAGNETICMAGNETICLATCH25AMPERESSPDTHERMETICALLYSEALEDPDF
链接地址:http://www.mydoc123.com/p-692978.html