DLA MIL-PRF-6106 10 F-2011 RELAY ELECTROMAGNETIC NORMALLY OPEN CONTINUOUS DUTY (INCLUDING UNSUPPRESSED and SUPPRESSED COILS) 60 AMP 3PST ENVIRONMENTALLY SEALED.pdf

《DLA MIL-PRF-6106 10 F-2011 RELAY ELECTROMAGNETIC NORMALLY OPEN CONTINUOUS DUTY (INCLUDING UNSUPPRESSED and SUPPRESSED COILS) 60 AMP 3PST ENVIRONMENTALLY SEALED.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-6106 10 F-2011 RELAY ELECTROMAGNETIC NORMALLY OPEN CONTINUOUS DUTY (INCLUDING UNSUPPRESSED and SUPPRESSED COILS) 60 AMP 3PST ENVIRONMENTALLY SEALED.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5945 MIL-PRF-6106/10F 07 November 2011 SUPERSEDING MIL-PRF-6106/10E 10 November 2000 PERFORMANCE SPECIFICATION SHEET RELAY, ELECTROMAGNETIC, NORMALLY OPEN, CONTINUOUS DUTY, (INCLUDING UNSUPPRESSED and SUPPRESSED COILS) 60 AMP, 3PST, ENVIRONMENTALLY SEALED This specification is approved

2、for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification sheet and MIL-PRF-6106. FIGURE 1. Relay, outline drawing. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitte

3、d without license from IHS-,-,-MIL-PRF-6106/10F 2 Inches mm Inches mm Inches mm .005 0.13 .250 6.35 1.375 34.92 .010 0.25 .309 7.85 1.74 44.2.02 0.5 .375 9.52 1.890 48.00 .028 0.71 .440 11.18 1.900 48.26.032 0.81 .530 13.46 2.000 50.80 .063 1.60 .600 15.24 2.115 53.72.148 3.76 .625 15.88 2.313 58.75

4、 .186 4.72 1.000 25.4 2.40 61.0 .240 6.10 1.060 26.92 2.500 63.503.032 77.01NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .031 (0.79 mm). 4. Weights include cover, barriers, and terminal hardware. 5. When

5、 using relay at rated 60 amps, the use of lugs per Burndy part number YAEV6C-G8 or equal is recommended. 6. Terminal temperature rise under continuous current conditions is 95C maximum. 7. Semiconductor devices shall be JANTX or equivalent. Diodes shall have a peak inverse voltage of 800 V dc minimu

6、m. 8. -005 relays shall not operate or be damaged by reversed polarity. FIGURE 1. Relay, outline drawing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dash number and operating characteristics. Dash no. Type Coil data Time mil

7、liseconds-maximum Coil Nominal Maximum Max pickup voltage 1/ Hold voltage 1/ Drop out voltage 1/ Operate 2/ Release 3/ Bounce Volts Freq Res Volts Ampere Normal 1/ High Temp Test Cont Current Test Main Auxiliary Inrush Steady state NO NC NO NC -001 1 X1, X2 28 DC - 29 1.25 .25 17 20 21.5 7.0 1.5 25

8、25 2 - - - -002 1 X1, X2 28 DC - 29 1.25 .25 17 20 21.5 7.0 1.5 25 25 2 - 2 2 -003 1 X1, X2 115 400 - 124 .71 .1 85 95 100 40 10 25 55 2 - - - -004 1 X1, X2 115 400 - 124 .71 .1 85 95 100 40 10 25 55 2 - 2 2 -005 4/ 1 X1, X2 28 DC - 29 1.25 .25 17 20 21.5 7.0 1.5 25 25 - - - - 1/ Over the temperatur

9、e range 2/ With nominal coil voltage 3/ From nominal coil voltage 4/ -005 is same as -001 except for transient suppressed coil. TABLE II. Rated contact load (amperes per pole) (case grounded). Type of load Life operating cycles x10328 V dc 1/ 115 V ac, 1 phase 1/ 115/200 V ac, 3 phase 1/ Main Auxili

10、ary Main Auxiliary Main Auxiliary NO NC NO NC 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz Resistive 100 - - 3 3 60 - 3 - 60 - - - Inductive 100 - - 1.5 1.5 60 - 1.5 - 60 - - - Motor 50 - - - - 40 - - - 40 - - - Lamp - - .5 .5 - .5 - - - - Transfer load 2/ - - - - - - - Mechanical life reduce

11、d current 200 - - .75 .75 15 - .75 - 15 - - - Mixed loads 3/ 50 - - Per spec 4 - - - 4 - - - 1/ Absence of value indicates relay is not rated for that application. 2/ Transfer load indicates relay suitable for transfer between unsynchronized ac power supplies at rating. 3/ Mixed loads to be conducte

12、d at +71C. Number of mixed loads cycles following continuous current test - 5000.MIL-PRF-6106/10F3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/10F 4 REQUIREMENTS Weight: 001 and 002 and -005: 10 ounces maximum. 003 and 004: 11 ounces

13、 maximum. Temperature range: -55C to +71C. Maximum altitude rating: 50,000 feet. 1/ Shock g-level: .5 sine, 25 gs. Duration: 6 to 9 ms. Maximum duration contact opening: 1 ms. Vibration-sinusoidal: See table III. TABLE III. Vibration-sinusoidal. Dash No. Vibration level 5-10 Hz 10-55 Hz 55-400 Hz 40

14、0-800 Hz 800 - 2000 Hz -55C and 25C +71C -001 .08 DA .06 DA 10 gs 10 gs 10 gs 7 gs -002 10 gs 8 gs 8 gs 7 gs -003 10 gs 10 gs 10 gs 7 gs -004 10 gs 8 gs 8 gs 7 gs -005 10 gs 10 gs 10 gs 7 gs Vibration (random): Not applicable. Acceleration: 15 gs. Seal: Applicable specification: MIL-STD-202, method

15、112, test condition C, procedure IV. Leak rate: 6x10-4 std cc/s. Strength of terminals and mounting studs: Torque: Main terminals: 24 inch-pounds maximum, 18 inch-pounds recommended installation torque. Auxiliary terminals: 4.4 inch-pounds maximum, 3.3 inch-pounds recommended installation torque. In

16、sulation resistance, initial. 200 megohms minimum. After life or environmental tests. 100 megohms minimum. 1/ Application range can be extended to 80,000 feet by suitably encapsulating the terminals. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI

17、L-PRF-6106/10F 5 Dielectric withstanding voltage (sea level): 2 to 5 seconds. Initial 28 V dc 115 V ac After life tests 28 V dc 115 V ac Coil to case - - - - - - - - - - - - - - - - - - - - - 1,250 1,500 1,000 1,125 Auxiliary contacts - - - - - - - - - - - - - - - - - 1,250 1,250 1,000 1,000 Across

18、open power contacts - - - - - - - - - 1,250 1,250 625 625 All other points - - - - - - - - - - - - - - - - - - - 1,800 1,800 1,350 1,350 Dielectric withstanding voltage (altitude): 1 minute. 28 V dc 115 V ac Coil to case - - - - - - - - - - - - - - - - - 500 500 Auxiliary contacts - - - - - - - - -

19、- - - - 500 500 All other points - - - - - - - - - - - - - - - 700 700 Maximum contact drop, initial: .150 volt After life test: .200 volt. Overload current: 320 amperes (ac). 1/ Rupture current: 400 amperes (ac). Coil suppression (transient voltage, back emf): 45 V dc maximum. Duty rating: Continuo

20、us. RFI specification (applicable to coil circuits of ac operated relays): MIL-STD-461. Part number. M6106/10- (dash number from table I). Qualification by similarity: See MIL-PRF-6106. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where ch

21、anges from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the

22、 marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-6106, this document references the following: MIL-STD-202 MIL-STD-461 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/10F 6 Cus

23、todian: Preparing activity: Air Force - 85 DLA - CC DLA - CC (Project 5945-2011-060)Review activities: Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-