DLA MIL-PRF-39012 57 H-2011 CONNECTORS PLUGS ELECTRICAL COAXIAL RADIO FREQUENCY (SERIES SMA (CABLED) SOCKET CONTACT CLASS 2).pdf
《DLA MIL-PRF-39012 57 H-2011 CONNECTORS PLUGS ELECTRICAL COAXIAL RADIO FREQUENCY (SERIES SMA (CABLED) SOCKET CONTACT CLASS 2).pdf》由会员分享,可在线阅读,更多相关《DLA MIL-PRF-39012 57 H-2011 CONNECTORS PLUGS ELECTRICAL COAXIAL RADIO FREQUENCY (SERIES SMA (CABLED) SOCKET CONTACT CLASS 2).pdf(17页珍藏版)》请在麦多课文档分享上搜索。
1、INCH-POUND MIL-PRF-39012/57H 14 July 2011 SUPERSEDING MIL-PRF-39012/57G 9 August 2006 PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL, RADIO FREQUENCY, (SERIES SMA (CABLED) SOCKET CONTACT, CLASS 2) This specification is approved for use by all Departments and Agencies of the D
2、epartment of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. For dimension A, see tables I and V. 4. Dimension .400 inch (10.
3、16 mm) is the largest overall diameter of the connector. 5. Wrench flats are to accommodate standard wrench opening in accordance with FED-STD-H28, appendix 10. 6. Dimension A defines the overall length of the connector when assembled to the cable. 7. All undimensioned pictorial configurations are f
4、or reference purposes only. 8. Series SMA, socket contact interface, in accordance with MIL-STD-348. 9. Metric equivalents are in parentheses. FIGURE 1. General configuration. AMSC N/A FSC 5935 MARKING IMPLEMENTATION DATE, CATEGORY B, SEE TABLE VII Provided by IHSNot for ResaleNo reproduction or net
5、working permitted without license from IHS-,-,-MIL-PRF-39012/57H 2 NOTES: 1. Dimensions are in inches. 2. Slitting of inner contact optional. 3. Metric equivalents are given for information only. 4. Chamfer is optional, if chamfer is used put on a 30 maximum. FIGURE 2. Mating dimensions for socket t
6、ermination, category D only. Inches mm Inches mm .001 .005 .008 .015 0.03 0.13 0.20 0.38 .021 .042 .045 .139 0.53 1.07 1.14 3.53 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/57H 3 TABLE I. Dash numbers, cross-reference, and dimension
7、s. Dash No. 1/ # Applicable cable group from MIL-PRF-39012, appendix B Dimensions Inches 2/ (millimeters) Maximum CATEGORY A FIELD SERVICEABLE (NO SPECIAL TOOLS REQUIRED) 3/ 3006 4006 Cable group I M17/93-RG178 4/ 5/ A .960 (24.38) 3007 4007 Cable group II M17/113-RG316 4/ 5/ 3008 4008 Cable group I
8、V M17/54-RG122 4/ 5/ 3009 4009 Cable group VI M17/84-RG223 4/ M17/128-RG400 5/ M17/60-RG142 6/ 3010 * 4010 * Cable group VI M17/111-RG303 4/ 5/ 3030 4030 Cable group III M17/152-00001 4/ 5/ See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
9、e from IHS-,-,-MIL-PRF-39012/57H 4 TABLE I. Dash numbers, cross-reference, and dimensions Continued. Dash No. 1/ # Applicable cable group from MIL-PRF-39012, appendix B Dimensions Inches 2/ (millimeters) Maximum CATEGORY C FIELD REPLACEABLE (MIL-C-22520/5 CRIMP TOOL) SEE FOOTNOTE NEXT TO APPLICABLE
10、CABLE GROUP FOR CRIMP DIE 7/ 3025 4025 Cable group I 8/ M17/93-RG178 4/ 5/ A 1.265 (32.13) 3026 4026 Cable group IIa 9/ M17/113-RG316 4/ 5/ 3027 4027 Cable group IV 10/ M17/54-RG122 4/ 5/ 3028 4028 Cable group VIb 11/ M17/84-RG223 4/ M17/128-RG400 5/ M17/60-RG142 6/ 3029 4029 Cable group VIa 11/ M17
11、/28-RG058 4/ M17/111-RG303 5/ CATEGORY D FIELD REPLACEABLE DEFINED PIECE PARTS 4/ 12/ 13/ 3502 4502 Cable group VIb M17/60-RG142 4/ 6/ M17/128-RG400 5/ A 1.265 (32.13) 1/ These connectors have captivated center contacts. 2/ Dimensions are in inches. Metric equivalents are given for information only.
12、 3/ All corrosion resistant steel bodied connectors which are designed to be assembled to the outer conductor using solder shall be gold plated in accordance with ASTM B488, type II, code C, class 1.27. 4/ Cable to be used when performing tests except as in note 6/. 5/ Preferred cable. 6/ Cable to b
13、e used for +200C temperature cycling test. 7/ These connectors are assembled, using the applicable crimp tool, to the specified cables stripped as shown on figures 3 and 4. 8/ Preferred die M22520/5-33 closure B, alternate die M22520/5-03 closure B. 9/ Preferred die M22520/5-35 closure B, alternate
14、die M22520/5-03 closure A. 10/ Preferred die M22520/5-41 closure B, alternate die M22520/5-05 closure B or -09 closure A. 11/ Preferred die M22520/5-19 closure B, alternate die M22520/5/-05 closure A or -11, 57 closure A. 12/ Complete connector assembly shall consist of a body, center contact, ferru
15、le and assembly instructions. 13/ Not for use in Army equipment. # The latest version of each cable shall be applicable. * These parts are inactive for new design, new designs should procure to dash numbers X009 and X109. These dash numbers use the same cable group (VI). Connectors mate with connect
16、ors of the same material; i.e., “3XXX” series dash numbers mate only with other “3XXX” series connectors and “4XXX” series connectors with other “4XXX” series connectors. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/57H 5 Inches mm I
17、nches mm Inches mm .001 .002 .003 .005 .010 .015 .024 0.03 0.05 0.08 0.13 0.25 0.38 0.61 .035 .038 .041 .050 .062 .133 .153 0.89 0.97 1.04 1.27 1.57 3.38 3.89 .193 .220 .250 .326 .500 4.90 5.59 6.35 8.28 12.70 Dash No. Contact No. 1/ A (inches) Basic crimp tool 2/ Crimp die or positioner Crimp tensi
18、le minimum Color band Color band 3502 4502 57-10 .041 .001 M22520/1-01 Solder or M22520/1-15 4 pounds (17.79 N) Red Maroon 1/ Contact numbers are for identification purposes only. 2/ Class 2 tool may be used by OEM (see MIL-DTL-22520). FIGURE 3. Contact and ferrule dimensions for category D only. Pr
19、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/57H 6 Dash No. Ferrule No. 1/ A B Basic crimp tool 2/ Crimp die or positioner M22520/5- 3502 4502 57-50 .250 .003 .220 .003 M22520/5-01 -11, -05, -57 closure A and -19 closure B 1/ Ferrule n
20、umbers are for identification only. 2/ Class 2 tools may be used by OEM (see MIL-DTL-22520). NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Crimp tensile test shall be in accordance with SAE-AS39029. 4. Copyright notice: All information disclosed in this
21、 specification sheet which is or may be copyrighted is reproduced herein with the express permission of the copyright owner. 5. .003 inch maximum break. 6. Color bands shall be positioned such that no coloring material enters the inspection hole. FIGURE 3. Contact and ferrule dimensions for category
22、 D only Continued. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. FIGURE 4. Cable stripping dimensions for field replaceable connectors. Inches mm .130 .150 .271 .291 .380 .400 .530 3.30 3.81 6.88 7.39 9.65 10.16 13.46 Provided by IHSNot for ResaleNo reprod
23、uction or networking permitted without license from IHS-,-,-MIL-PRF-39012/57H 7 ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 to 12.4 GHz. Voltage rating: The voltage rating shall be in accordance with table II. TABLE II. Voltage rating. Cables Voltage max. (sea level) V rms Volta
24、ge max. at 70,000 ft (4.437 kPa) V rms Cable group I 170 45 Cable group II, IIa, III, IV 250 65 Cable group VI, VIa, VIb 335 85 Temperature rating: -65C to +165C. REQUIREMENTS: Dimensions and configuration: See figure 1 and MIL-STD-348. Force to engage and disengage: Longitudinal force: Not applicab
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILPRF3901257H2011CONNECTORSPLUGSELECTRICALCOAXIALRADIOFREQUENCYSERIESSMACABLEDSOCKETCONTACTCLASS2PDF

链接地址:http://www.mydoc123.com/p-692873.html