DLA MIL-PRF-28861 12 G-2012 FILTERS AND CAPACITORS RADIO FREQUENCY ELECTROMAGNETIC INTERFERENCE SUPPERESSION HERMETICALLY SEALED ON ONE END ONLY STYLE FS70.pdf
《DLA MIL-PRF-28861 12 G-2012 FILTERS AND CAPACITORS RADIO FREQUENCY ELECTROMAGNETIC INTERFERENCE SUPPERESSION HERMETICALLY SEALED ON ONE END ONLY STYLE FS70.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-PRF-28861 12 G-2012 FILTERS AND CAPACITORS RADIO FREQUENCY ELECTROMAGNETIC INTERFERENCE SUPPERESSION HERMETICALLY SEALED ON ONE END ONLY STYLE FS70.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 59GP INCH-POUND MIL-PRF-28861/12G 23 January 2012 SUPERSEDING MIL-PRF-28861/12F 14 February 2008 PERFORMANCE SPECIFICATION SHEET FILTERS, AND CAPACITORS, RADIO FREQUENCY/ELECTROMAGNETIC INTERFERENCE, SUPPERESSION, HERMETICALLY SEALED ON ONE END ONLY, STYLE FS70 This specification is app
2、roved for use by all Departments and Agencies of the Department of Defense. The complete requirements for acquiring the filters described herein shall consist of this specification sheet and the latest issue of MIL-PRF-28861. FIGURE 1. Case dimensions and circuit diagrams. Provided by IHSNot for Res
3、aleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-28861/12G 2 Dash number Configuration 001 thru 016 033 and 034 A 017 thru 032 035 and 036 B Inches mm Inches mm .002 0.05 .156 3.96 .005 0.13 .200 5.08 .020 0.51 .250 6.35 .030 0.76 .625 15.88 .110 2.79 .715 18.16 .128 3
4、.25 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm). 4. Circuit diagrams are for information only. 5. Filters shall be supplied with 60/40 solder preform. 6. Potting on non-hermetically seale
5、d end shall not extend beyond .030 inch (0.76 mm) from the filter body. 7. Filters shall be installed using the recommended installation methods (solder-in style of MIL-PRF-28861). FIGURE 1. Case dimensions and circuit diagrams - Continued. Circuit diagram A .005 B Ref L C .200 .110 .715 .625 Provid
6、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-28861/12G 3 REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Filters and capacitors shall be hermetically sealed on one end as shown in figure 1 for the respective st
7、yle. Weight: .25 gram maximum for C circuit parts. .75 gram maximum for L circuit parts. Case and lead finish: G only (gold plated). Terminals: Solderable. Operating temperature range: -55C to +125C. Rated voltage: See table I. Rated current: 5 amperes, maximum. Capacitance: See table I. Dissipation
8、 factor: 2 percent maximum for capacitance values 10 pF through 100pF and 3 percent maximum for values greater than 100pF. Voltage and temperature limits of capacitance: +15 percent, -40 percent. Insulation resistance: At +25C: 1,000 megohm-microfarads, or 100,000 megohms minimum, whichever is less.
9、 At +125C: 100 megohm-microfarads or 10,000 megohms minimum, whichever is less. Insertion loss: At +25C: In accordance with table I. At -55C and +125C: A 3 dB degradation from +25C value shall be allowed. Voltage drop: 0.05 volt maximum. DC resistance: 0.01 ohm maximum. Seal: Not applicable. Tempera
10、ture rise: +25C, maximum. Solderability of terminals: In accordance with MIL-PRF-28861, except the temperature of the solder shall be +300C +0C, -5C. Resistance to soldering heat: In accordance with MIL-PRF-28861, except the temperature of the solder shall be +300C +0C, -5C. Provided by IHSNot for R
11、esaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-28861/12G 4 Solderability of mounting termination: In accordance with MIL-PRF-28861, except the temperature of the solder shall be +300C +0C, -5C. Quality assurance provisions: In accordance with MIL-PRF-28861. Product
12、 assurance level: In accordance with table I. TABLE I. Electrical Characteristics. Dash Number Circuit Product Assurance level Rated Voltage Volts dc Capacitance (pF) -0 +100 percent Minimum insertion loss (dB) in Accordance with MIL-STD-220 1/ 2/ Minimum Insertion loss At resonant Frequency 3/ Clas
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILPRF2886112G2012FILTERSANDCAPACITORSRADIOFREQUENCYELECTROMAGNETICINTERFERENCESUPPERESSIONHERMETICALLYSEALEDONONEENDONLYSTYLEFS70PDF

链接地址:http://www.mydoc123.com/p-692810.html