DLA MIL-PRF-27 290 C-2008 TRANSFORMER AUDIO FREQUENCY《音频变压器》.pdf

《DLA MIL-PRF-27 290 C-2008 TRANSFORMER AUDIO FREQUENCY《音频变压器》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-27 290 C-2008 TRANSFORMER AUDIO FREQUENCY《音频变压器》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5950 INCH-POUND MIL-PRF-27/290C 18 July 2008 SUPERSEDING MIL-PRF-27/290B 23 April 2003 PERFORMANCE SPECIFICATION SHEET TRANSFORMER, AUDIO FREQUENCY This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The complete requirements for procur

2、ing the transformer described herein shall consist of this document and the latest issue of specification MIL-PRF-27. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Marking shall be on the side of the case. FIGURE 1. Dimensions and configurations

3、. INCHES MM .016 0.41 .030 0.76 .25 6.4 .344 8.74 .469 11.91 1.50 38.1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-27/290C 2 VS1= VS2.05% when: P= 15 sin 2(400 20)T where T = Time in sec. RL1= RL2= 15 k thru 1 M. FIGURE 2. Output balance

4、circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-27/290C 3 REQUIREMENTS: (When colors in parentheses, i.e. (Brn-Blu), are used, they indicate the winding and the extreme terminals of the winding. When the extreme terminals of two wind

5、ings are used, i.e. (Brn-Blu), the windings are connected in series.) Electrical ratings: Primary power level: 100 mW maximum at 1 kHz. Working voltage: 50 Volts peak. Primary impedance: (Blu-Brn) 1,125 ohms ct 125 ohms. Secondary impedance: (Yel-Grn) 18,000 ohms split 2,000 ohms. Split indicates th

6、at one-fourth of the listed impedance is available by paralleling the windings. Primary current: 3.5 mA. Frequency range: 300 Hz to 20 kHz, 3 dB at 1 mW level. Design and construction: Dimensions and configuration: See figure 1. Duty cycle: Continuous. Case: Metal, one open end filled with epoxy. Te

7、rminals: Copper clad, steel tinned 100 percent, electroplated per ASTM B545 and ASTM B339. Diameter: 0.016 inch. Length: 1.500 0.250 inch. Weight: 0.2 ounce maximum. Operating temperature range: -55C to +130C. Altitude: 150,000 feet. Terminal strength: Method 211 of MIL-STD-202, test condition A, 2

8、pounds. Dielectric withstanding voltage (each winding): At sea level and at reduce barometric pressure: 100 Vrms. Polarity: Additive with terminals Blu and Yel, and Wht and Blk connected. Electrical characteristics: Primary Impedance: 1,125 ohms ct 12 percent with 1 volt at 5 kHz and 3.5 mA dc appli

9、ed to the primary and 18 k across the secondaries. Primary dc resistance: 120 ohms 25 percent. Secondary dc resistance: 940 ohms 25 percent. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-27/290C 4 No load (center tap unbalanced): 1 percent

10、at 1 volt, 5 kHz across the primary. Harmonic distortion: Total harmonic content of the output shall be a maximum of 5 percent at 100 mW and 3.5 mA in the primary. Secondary output balance: When the transformers are operated with identical loads of 15 k to 1 M on each of the secondary windings and t

11、he primary input voltage is equal to 15 sin 2(400 20) T, where T = time in seconds, the output voltages shall be equal within .05% (see figure 2). Insertion loss: At 100 mW in the primary, the insertion loss shall be a maximum of 3.0 dB at 1 kHz. Frequency response: ZS= 1,000 ohms; ZL= 16 k, EL= 1 v

12、olt; reference frequency = 1 kHz. Frequency range is 300 Hz to 20 kHz, 3.0 dB. Self-resonant frequency: Shall be a minimum of 300 kHz. Vibration (high frequency): MIL-STD-202, method 204, test condition B. Marking location: See figure 1. Part or Identification Number (PIN): M27/290-01. Changes from

13、previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are ca

14、utioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. MIL-PRF-27 MIL-STD-202 ASTM B339 ASTM B545 Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Forc

15、e - 85 (Project 5950-2008-036) DLA - CC Review activities: Army - AR, CR4, MI Navy - AS, MC, OS, SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-