DLA MIL-PRF-22885 113 A-2010 SWITCHES PUSHBUTTON ILLUMINATED 1 17 BY 96 LIGHT EMITTING DIODE (LED) SUNLIGHT READABLE VOLTAGE DIMMABLE NIGHT VISION GOGGLE COMPATIBLE EMC COMPLIANT C.pdf

《DLA MIL-PRF-22885 113 A-2010 SWITCHES PUSHBUTTON ILLUMINATED 1 17 BY 96 LIGHT EMITTING DIODE (LED) SUNLIGHT READABLE VOLTAGE DIMMABLE NIGHT VISION GOGGLE COMPATIBLE EMC COMPLIANT C.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-22885 113 A-2010 SWITCHES PUSHBUTTON ILLUMINATED 1 17 BY 96 LIGHT EMITTING DIODE (LED) SUNLIGHT READABLE VOLTAGE DIMMABLE NIGHT VISION GOGGLE COMPATIBLE EMC COMPLIANT C.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5930 INCH POUND MIL-PRF-22885/113A 6 May 2010 MIL-PRF-22885/113 6 May 2008 PERFORMANCE SPECIFICATION SHEET SWITCHES, PUSHBUTTON, ILLUMINATED, 1.17 BY .96, LIGHT EMITTING DIODE (LED), SUNLIGHT READABLE, VOLTAGE DIMMABLE, NIGHT VISION GOGGLE COMPATIBLE, EMC COMPLIANT, COMMON TERMINATION S

2、YSTEM (CTS), SPDT, DPDT, 4PDT, LOGIC LEVEL TO 7.5 AMPERES, DRIPPROOF, WATERTIGHT, SPLASHPROOF, HIGH IMPACT SHOCK RESISTANT This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall cons

3、ist of this specification sheet and MIL-PRF-22885. NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .010 for three place decimals and .03 for two place decimals. 3. The switch shall accommodate mounting to pa

4、nels from .032 to .187 thick. 4. A mounting spacer is supplied with each switch unit for SAE-AS7788 panel requirements and places the mounting flange flush with the top of a .235 thick edge lighted panel when used in front of the panel. Otherwise, the spacer is used behind the panel. 5. Pushbutton c

5、ap shall be designed to prevent incorrect insertion into switch housing. 6. Pushbutton cap shall be held captive to switch body by retaining element to prevent accidental interchange. 7. Exact shape of switch is optional provided dimensions specified are not exceeded. 8. Terminals and basic switch i

6、dentification shall be permanently marked as shown on figure 12. FIGURE 1. Switch - type I, 2 pole (enclosure design 1, unsealed with solder terminals). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113A 2 NOTES: 1. Dimensions are in

7、inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .010 for three place decimals and .03 for two place decimals. 3. The switch shall accommodate mounting to panels from .032 to .187 thick. 4. A mounting spacer is supplied with each switch

8、 unit for SAE-AS7788 panel requirements and places the mounting flange flush with the top of a .235 thick edge lighted panel when used in front of the panel. Otherwise, the spacer is used behind the panel. 5. Pushbutton cap shall be designed to prevent incorrect insertion into switch housing. 6. Pus

9、hbutton cap shall be held captive to switch body by retaining element to prevent accidental interchange. 7. Exact shape of switch is optional provided dimensions specified are not exceeded. 8. Terminals and basic switch identification shall be permanently marked as shown on figure 12. FIGURE 2. Swit

10、ch - type II, 2 pole (enclosure design 2, 3, and 4; dripproof, watertight, and splashproof with solder terminals). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113A 3 NOTES: 1. Dimensions are in inches. Metric equivalents are given f

11、or general information only. 2. Unless otherwise specified, tolerances are .010 for three place decimals and .03 for two place decimals. 3. The switch shall accommodate mounting to panels from .032 to .187 thick. 4. A mounting spacer is supplied with each switch unit for SAE-AS7788 panel requirement

12、s and places the mounting flange flush with the top of a .235 thick edge lighted panel when used in front of the panel. Otherwise, the spacer is used behind the panel. 5. Pushbutton cap shall be designed to prevent incorrect insertion into switch housing. 6. Pushbutton cap shall be held captive to s

13、witch body by retaining element to prevent accidental interchange. 7. The Common Termination System (CTS) connector shall be designed and constructed to meet the performance requirements of this document. This item, M22885/108-18200 for 2 pole switches, shall be acquired from a source listed on QPL-

14、22885. 8. The CTS connector shall be removable from the switch housing to allow the housing to be mounted separately. The connector may be wired during harnessing operations, allowing bench testing without the need of the switch housing 9. The CTS connector shall be considered as a connector plug th

15、at may be separated from the switch housing for the convenience of installation. 10. The CTS connector shall be removable from the switch body by use of a M22885/108-T8234 CTS module extraction tool. Refer to MIL-PRF-22885/108 for details. This item shall be acquired from a source listed on QPL-2288

16、5. 11. The CTS connector shall be capable of receiving SAE-AS39029/22-192 socket contacts crimped to a 20, 22, or 24 gauge wire. 12. The CTS connector shall be capable of having the socket contacts inserted or removed using an M81969/14-10 contact insertion/removal tool. 13. Exact shape of switch is

17、 optional provided dimensions specified are not exceeded. 14. Terminals and basic switch identification shall be permanently marked as shown on figure 12. FIGURE 3. Switch - type III (enclosure design 1; unsealed with 2 pole common termination system). 1.93 MAX FROM FRONT OF PANEL Provided by IHSNot

18、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113A 4 Notes 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .010 for three place decimals and .03 for two place decimal

19、s. 3. The switch shall accommodate mounting to panels from .032 to .187 thick. 4. A mounting spacer is supplied with each switch unit for SAE-AS7788 panel requirements and places the mounting flange flush with the top of a .235 thick edge lighted panel when used in front of the panel. Otherwise, the

20、 spacer is used behind the panel. 5. Pushbutton cap shall be designed to prevent incorrect insertion into switch housing. 6. Pushbutton cap shall be held captive to switch body by retaining element to prevent accidental interchange. 7. The Common Termination System (CTS) connector shall be designed

21、and constructed to meet the performance requirements of this document. This item, M22885/108-18200 for 2 pole switches, shall be acquired from a source listed on QPL-22885. 8. The CTS connector shall be removable from the switch housing to allow the housing to be mounted separately. The connector ma

22、y be wired during harnessing operations, allowing bench testing without the need of the switch housing 9. The CTS connector shall be considered as a connector plug that may be separated from the switch housing for the convenience of installation. 10. The CTS connector shall be removable from the swi

23、tch body by use of a M22885/108-T8234 CTS module extraction tool. Refer to MIL-PRF-22885/108 for details. This item shall be acquired from a source listed on QPL-22885. 11. The CTS connector shall be capable of receiving SAE-AS39029/22-192 socket contacts crimped to a 20, 22, or 24 gauge wire. 12. T

24、he CTS connector shall be capable of having the socket contacts inserted or removed using an M81969/14-10 contact insertion/removal tool. 13. Exact shape of switch is optional provided dimensions specified are not exceeded. 14. Terminals and basic switch identification shall be permanently marked as

25、 shown on figure 12. FIGURE 4. Switch - type IV (enclosure design 2, 3, and 4; dripproof, watertight and splashproof with 2 pole common termination system) 1.85 MAX FROM FRONT OF PANEL Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113

26、A 5 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .010 for three place decimals and .03 for two place decimals. 3. The switch shall accommodate mounting to panels from .032 to .187 thick. 4. A mounting spa

27、cer is supplied with each switch unit for SAE-AS7788 panel requirements and places the mounting flange flush with the top of a .235 thick edgelighted panel when used in front of the panel. Otherwise, the spacer is used behind the panel. 5. Pushbutton cap shall be designed to prevent incorrect insert

28、ion into switch housing. 6. Pushbutton cap shall be held captive to switch body by retaining element to prevent accidental interchange. 7. The Common Termination System (CTS) connector shall be designed and constructed to meet the performance requirements of this document. This item, M22885/108-C824

29、0 for 4 pole switches, shall be acquired from a source listed on QPL-22885. 8. The CTS connector shall be removable from the switch housing to allow the housing to be mounted separately. The connector may be wired during harnessing operations, allowing bench testing without the need of the switch ho

30、using 9. The CTS connector shall be considered as a connector plug that may be separated from the switch housing for the convenience of installation. 10. The CTS connector shall be removable from the switch body by use of a M22885/108-T8234 CTS module extraction tool. Refer to MIL-PRF-22885/108 for

31、details. This item shall be acquired from a source listed on QPL-22885. 11. The CTS connector shall be capable of receiving SAE-AS39029/22-192 socket contacts crimped to a 20, 22, or 24 gauge wire. 12. The CTS connector shall be capable of having the socket contacts inserted or removed using an M819

32、69/14-10 contact insertion/removal tool. 13. Exact shape of switch is optional provided dimensions specified are not exceeded. 14. Terminals and basic switch identification shall be permanently marked as shown on figure 12. FIGURE 5. Switch - type V (enclosure design 1: unsealed with 4 pole common t

33、ermination system) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113A 6 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .010 for three place

34、decimals and .03 for two place decimals. 3. The switch shall accommodate mounting to panels from .032 to .187 thick. 4. A mounting spacer is supplied with each switch unit for SAE-AS7788 panel requirements and places the mounting flange flush with the top of a .235 thick edgelighted panel when used

35、in front of the panel. Otherwise, the spacer is used behind the panel. 5. Pushbutton cap shall be designed to prevent incorrect insertion into switch housing. 6. Pushbutton cap shall be held captive to switch body by retaining element to prevent accidental interchange. 7. The Common Termination Syst

36、em (CTS) connector shall be designed and constructed to meet the performance requirements of this document. This item, M22885/108-C8240 for 4 pole switches, shall be acquired from a source listed on QPL-22885. 8. The CTS connector shall be removable from the switch housing to allow the housing to be

37、 mounted separately. The connector may be wired during harnessing operations, allowing bench testing without the need of the switch housing 9. The CTS connector shall be considered as a connector plug that may be separated from the switch housing for the convenience of installation. 10. The CTS conn

38、ector shall be removable from the switch body by use of a M22885/108-T8234 CTS module extraction tool. Refer to MIL-PRF-22885/108 for details. This item shall be acquired from a source listed on QPL-22885. 11. The CTS connector shall be capable of receiving SAE-AS39029/22-192 socket contacts crimped

39、 to a 20, 22, or 24 gauge wire. 12. The CTS connector shall be capable of having the socket contacts inserted or removed using an M81969/14-10 contact insertion/removal tool. 13. Exact shape of switch is optional provided dimensions specified are not exceeded. 14. Terminals and basic switch identifi

40、cation shall be permanently marked as shown on figure 12. FIGURE 6. Switch- type VI (enclosure design 2, 3, and 4: dripproof, watertight, and splashproof with 4 pole common termination system). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-

41、22885/113A 7 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .010 for three place decimals and .03 for two place decimals. FIGURE 7. Switch and lighting circuit terminations, Type I and II, dimensions and ce

42、nter location. Inches mm .003 0.08 .010 0.25 .020 0.51 .030 0.76 .04 1.0 .06 1.5 .069 1.75 .106 2.69 .125 3.18 .150 3.81 .213 5.41 .237 6.02 .500 12.70 .698 17.73 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113A 8 NOTES: 1. Dimensio

43、ns are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .010 for three place decimals and .03 for two place decimals. FIGURE 8. Switch and lighting circuit terminations, Common Termination System (CTS), interface. Provided by IHSNot

44、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113A 9 FIGURE 9. Switch circuit configurations, schematics. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113A 10 FIGURE 10. LED circuit conf

45、igurations, schematics. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113A 11 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .010 for three

46、place decimals and .03 for two place decimals. FIGURE 11. Recommended panel cutouts. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113A 12 FIGURE 12. Switch poles and lighting circuit terminal arrangements and identification. Provided

47、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/113A 13 NOTES: 1. All 2 pole common termination system (CTS) switches have identical switch and lighting circuit terminal arrangement identification. All 4 pole CTS switches have identical switch

48、and lighting circuit terminal arrangement identification. 2. To make the various CTS combinations, an MS27488-20 sealing plug is placed in the locations not to be used. In the above identifications, blackened circles indicate where the sealing plugs shall be located to form the described variation. 3. “SKT“ identifies the socket side. 4. A and B or H, J, K and L identify each switch pole. 5. C, B, G, F, D, and A identify the lighting circuit terminations. 6. 1, 2, 3, and 4 identify the switch contact termination. FIGURE 12. S