DLA MIL-PRF-19207 6 P-2012 FUSEHOLDERS EXTRACTOR POST TYPE BLOWN FUSE INDICATING AND NONINDICATING TYPE FHL15G.pdf

《DLA MIL-PRF-19207 6 P-2012 FUSEHOLDERS EXTRACTOR POST TYPE BLOWN FUSE INDICATING AND NONINDICATING TYPE FHL15G.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-19207 6 P-2012 FUSEHOLDERS EXTRACTOR POST TYPE BLOWN FUSE INDICATING AND NONINDICATING TYPE FHL15G.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5920 MIL-PRF-19207/6P 13 March 2012 SUPERSEDING MIL-PRF-19207/6N 28 March 2006 PERFORMANCE SPECIFICATION SHEET FUSEHOLDERS, EXTRACTOR POST TYPE, BLOWN FUSE INDICATING AND NONINDICATING, TYPE FHL15G This specification is approved for use by all Departments and Agencies of the Department

2、of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-19207. FIGURE 1. Type FHL15G fuseholder. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/6P 2 PANEL

3、 MOUNTING HOLES NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .02 (0.5 mm) for two place decimals. 3. Metric equivalents are given for general information only. FIGURE 1. Type FHL15G fuseholder - Continued. Inches mm Inc

4、hes mm Inches mm Inches mm .060 .096 .250 .281 .313 .967 1.52 2.44 6.40 7.14 7.95 24.56 .97 1.00 1.13 1.375 1.38 24.6 25.4 28.7 34.93 35.1 1.44 1.75 1.875 1.88 2.187 36.6 44.5 47.63 47.8 55.55 2.50 2.69 3.00 3.63 7.13 63.6 68.3 76.2 92.2 181.1 Provided by IHSNot for ResaleNo reproduction or networki

5、ng permitted without license from IHS-,-,-MIL-PRF-19207/6P 3 REQUIREMENTS: Dimensions and configuration: See figure 1. Cap and body molding material: It is recommended that types MAI-60, GDI-30F or SDG-F of American Society for Testing and Materials ASTM-D5948 be considered for meeting the body mold

6、ing material requirements of this specification. ASTM-D3935 is also suggested as guidance for cap material. The military part number is not required on the fuseholder. Fuse accommodation: MIL-PRF-15160, style F63 or equivalent size and style. Poles: One. Rating: 61 amperes to 100 amperes, 90 volts t

7、o 500 volts. Panel thickness: 0.250 inch (6.35 mm) maximum. Indicating: Neon lamp with clear cap. Lamp series resistors: MIL-PRF-39017/2, two 160,000 ohms, 0.5 watt. One each lamp lead for indicating model; none required for nonindicating model. Nonindicating: No lamp or resistor required. Cap, colo

8、r, gray. Terminals: Stud type, No. 5/16-18UNC-2A thread. Enclosure: Dripproof. Test fuses: Temperature rise: F63C500V100A of MIL-PRF-15160/63. Short circuit: F63C500V100A of MIL-PRF-15160/63. Mechanical shock: Method I of MIL-PRF-19207. Terminal strength: 20 pounds. Fuse clip retention force: Lower

9、clip: 6 pounds to 9 pounds. Cap clip: 12 pounds to 16 pounds. Salt spray (corrosion): Test condition B. Mounting hardware: Screw: .250-20UNC-2A trusshead, 2.75 inches (70 mm) long (min) with sealing washer. Nut: .250-20UNC-2B Hex. A threaded metal insert may be used in lieu of nut. Part or Identifyi

10、ng Number (PIN): FHL15G - (dash number from table I) supersedes the military part number: M19207/6 - (dash number from table I). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/6P 4 TABLE I. Indicating features. PIN/MIL dash number Indi

11、cating Nonindicating Superseded number (FSCM 81349) -001 -002 X X FHL15G Patent notice: The US Government has a royalty-free license under US Patent No. 3,225,164 and only under claim 4 of US Patent No. 2,989,610, owned by FIC Corporation, for the benefit of manufacturers of the items called for in

12、this specification sheet either for the Government or for use in equipment to be delivered to the Government. Referenced documents. In addition to MIL-PRF-19207, this document references the following: MIL-PRF-15160 MIL-PRF-15160/63 MIL-PRF-39017/2 ASTM-D3935 ASTM-D5948 The margins of this specifica

13、tion are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this

14、document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - SH AF - 85 (Project 5920-2011-079) DLA - CC Review activities: Army - AR, AT, AV, CR4, MI Navy - AS, EC, MC, OS Air Force

15、 - 70, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-