DLA MIL-PRF-19207 2 J-2013 FUSEHOLDERS EXTRACTOR POST TYPE BLOWN FUSE INDICATING TYPES FHL11U AND FHL11G.pdf

《DLA MIL-PRF-19207 2 J-2013 FUSEHOLDERS EXTRACTOR POST TYPE BLOWN FUSE INDICATING TYPES FHL11U AND FHL11G.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-19207 2 J-2013 FUSEHOLDERS EXTRACTOR POST TYPE BLOWN FUSE INDICATING TYPES FHL11U AND FHL11G.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5920 MIL-PRF-19207/2J 5 December 2013 SUPERSEDINGMIL-PRF-19207/2H 22 January 2007 PERFORMANCE SPECIFICATION SHEET FUSEHOLDERS, EXTRACTOR POST TYPE, BLOWN FUSE INDICATING, TYPES FHL11U AND FHL11G This specification is approved for use by all Departments and Agencies of the Department of

2、Defense The requirements for acquiring the product described herein shall consist of this specification and MIL-PRF-19207. Ltr Inches mm Ltr Inches mm Min Max Min Max Min Max Min Max A 1.070 REF 27.18 REF H .969 .979 24.61 24.87 B 1.200 REF 304.80 REF J .151 .161 3.84 4.09 C .055 .065 1.40 1.65 K .8

3、70 .880 22.10 22.35 D .830 REF 21.08 REF L .432 .442 10.97 11.23 E 3.750 4.000 95.25 101.60 M .370 .380 9.40 9.65 F .870 .880 22.10 22.35 N .745 .755 18.92 19.18 G .200 .210 5.08 5.33 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwis

4、e specified, tolerances are 0.02 (0.51 mm) for two place decimals and 0.005 (0.13mm) for three-place decimals. FIGURE 1. Type FHL11U and type FHL11G fuseholders. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/2J 2 Ltr Inches

5、 mm Ltr Inches mm Min Max Min Max Min Max Min Max A 1.060 1.080 26.92 27.43 L .435 .445 11.05 11.30 B .745 .755 18.92 19.18 M .850 .860 21.59 21.84 C .435 .445 11.05 11.30 N .385 .425 9.78 10.80 D .188 .198 4.78 5.03 P .140 .160 3.56 4.06 E .870 .880 22.10 22.35 R .695 .705 17.65 17.91 F .385 .395 9

6、.78 10.03 S .565 .605 14.35 15.37 G 1.190 1.210 30.23 30.73 T .140 .190 3.56 4.83 H .945 .955 24.00 24.26 U 1.675 - 42.55 - J .125 - 3.18 - V 1.950 2.050 49.53 52.07 K .360 .370 9.14 9.40 W 2.105 2.155 53.47 54.74 Part or Identifying Number (PIN): FHL11U-001 - Body for FHL11U FHL11G-002 - Body for F

7、HL11G NOTES: Fuse carrier for FHL11U-001 shall be FHL10U-003. Fuse carrier for FHL11G-002 shall be FHL10G-004. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are 0.02 (0.51 mm) for two place decimals and 0.0

8、05 (0.13mm) for three-place decimals. FIGURE 2. Body for FHL11U and FHL11G fuseholders. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/2J 3 REQUIREMENTS: Interface and physical dimensions: See figures 1 and 2. Cap and body molding mate

9、rial: Cap and body molding materials shall be selected to enable the fuseholder to meet the performance requirements of this specification. Additional information and guidance on body molding material are specified in the notes. Fuse accommodation. Ferrule type: Size: 0.250 inch (6.35 mm) diameter,

10、1.250 inches (31.75 mm) length. Styles: MIL-PRF-15160, F02 and F03 and MIL-PRF-23419, FM09. (or equivalent size and styles) Poles: One Rating: 30 amperes, 90-250 volts. Panel thickness: 0.125 inch (3.18 mm) maximum. Indicating: Neon lamp with clear cap. Lamp series resistor: MIL-PRF-39017/1, 120,000

11、 ohms, 0.25 watt. Terminals: Stud type, No. 8-32 UNC-2A thread. Enclosure: Unsealed: FHL11U. Dripproof: FHL11G (see note 1) Test fuses: Temperature rise: F03A125V30A of MIL-PRF-15160/3. Short circuit: F03A250V15A of MIL-PRF-15160/3. Mechanical shock: Method I of MIL-PRF-19207. Terminal strength: 20

12、pounds. Torque: Terminals - 15 pounds-inch. Salt atmosphere (corrosion): Test condition B. Mounting hardware: Screw: 6-32UNC-2A, 7/8-inch long (min). Pan/round head with sealing washer or pan self-sealing. Nut: 6-32UNC-2B Hex. A threaded metal insert may be used in lieu of nut. Provided by IHSNot fo

13、r ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/2J 4 NOTES: 1. All of the type FHL11G fuseholders submitted for delivery shall have been subjected to the dripproof test as specified in 4.6.16.2 of MIL-PRF-19207. 2. Cap and body molding material: It is sugge

14、sted that type MAI-60, GDI-30F or SDG-F of American Society for Testing and Materials ASTM-D5948 be considered for meeting the cap and body molding material requirements of this specification. ASTM-D3935 is also suggested as guidance for cap material. Referenced documents. In addition to MIL-PRF-192

15、07, this document references the following: MIL-PRF-15160 MIL-PRF-15160/3 MIL-PRF-23419 MIL-PRF-39017/1 ASTM-D3935 ASTM-D5948 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Gove

16、rnment assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing Ac

17、tivity: Army - CR DLA - CC Navy - SH Air force - 85 (Project 5920-2013-027) DLA - CC Review Activities: Army - AR, AT, CR4, MI Navy - AS, EC, MC, OS Air Force - 70, 71, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-