DLA MIL-PRF-15733 46 C (1)-2008 FILTERS RADIO FREQUENCY INTERFERENCE SUPPRESSION STYLE FL41.pdf

《DLA MIL-PRF-15733 46 C (1)-2008 FILTERS RADIO FREQUENCY INTERFERENCE SUPPRESSION STYLE FL41.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-15733 46 C (1)-2008 FILTERS RADIO FREQUENCY INTERFERENCE SUPPRESSION STYLE FL41.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5915 MIL-PRF-15733/46C W/AMENDMENT 1 21 April 2008 SUPERSEDING MIL-PRF-15733/46C 17 July 2003 PERFORMANCE SPECIFICATION SHEET FILTERS, RADIO FREQUENCY INTERFERENCE SUPPRESSION, STYLE FL41 This specification sheet is approved for use by all Depart- ments and Agencies of the Department of

2、 Defense. The requirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Circuit diagram for information only. 4. Recommended mounting torque

3、: 6-8 inches-pounds. 5. Case is ground terminal. 6. Mounting hardware (lockwasher and hex nut) shall be supplied with filter. 7. Turret head is optional. FIGURE 1. Case dimensions and circuit configurations. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

4、nse from IHS-,-,-TABLE I. Filter dimensions. A B C D E F G H J K Dash number Ref Min Max Min Max Min Max Min Max Min Max Min Max Ref Thread .015 (0.38) 0001 .250 (6.35) .110 (2.79) .140 (3.58) .141 (3.58) .171 (4.34) .141 (3.58) .171 (4.34) .406 (10.31) .468 (11.89) .656 (16.66) .718 (18.24) .235 (5

5、.97) .265 (6.73) .687 (17.45) 12-32 UNEF-2A .187 (4.75) TABLE II. Hardware dimensions. Hex Nut Lockwasher A B C D E Dash number Min Max Min Max Thread Min Max Min Max 0001 .235 (5.97) .265 (6.73) .070 (1.78) .080 (2.03) 12-32 UNF-2B .370 (9.40) .380 (9.65) .013 (0.33) .023 (0.58) FIGURE 1. Case dime

6、nsions and circuit configurations - Continued. MIL-PRF-15733/46CW/AMENDMENT12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/46C W/AMENDMENT 1 3 REQUIREMENTS: Configuration and dimensions: See figure 1 and tables I and II. Case: Metal.

7、 Case and hardware finish: In accordance with MIL-PRF-15733. Pure tin finish is prohibited. Terminals: Solderable. Rated voltage: 300 V dc over the operating temperature range. Rated current: 10 amperes, dc. Insertion loss: In accordance with MIL-PRF-15733 and table III. Capacitance to ground: In ac

8、cordance with MIL-PRF-15733. Measured capacitance shall be at least 4,000 pF. Temperature rise: +25C maximum. Dielectric withstanding voltage: In accordance with MIL-PRF-15733. The following exception shall apply: The test voltage shall be 900 V dc applied for 1.5 seconds. Barometric pressure (reduc

9、ed): In accordance with MIL-PRF-15733 and Method 105, MIL-STD-202; test condition D. Insulation resistance: In accordance with MIL-PRF-15733. The insulation resistance measured at +25C between both terminals connected together and the case shall be at least 10,000 megohms. Voltage drop: Not applicab

10、le. Overload: In accordance with MIL-PRF-15733. The following exception shall apply: Insulation resistance only shall be measured and shall meet initial requirements. Terminal strength: In accordance with MIL-PRF-15733 and Method 211, MIL-STD-202; test condition A. Applied force: 5 pounds. Salt atmo

11、sphere (corrosion): In accordance with MIL-PRF-15733 and Method 101, MIL-STD-202; test condition B. Thermal shock and immersion: Not applicable. Shock (specified pulse): In accordance with MIL-PRF-15733 and Method 213, MIL-STD-202; test condition I. Vibration, high frequency: In accordance with MIL-

12、PRF-15733 and Method 204, MIL-STD-202; test condition D. Moisture resistance: Not applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/46C W/AMENDMENT 1 4 Life: In accordance with MIL-PRF-15733 and Method 108, MIL-STD-202; test c

13、ondition D. The following exceptions shall apply: Test voltage: 600 V dc. Following the test, insulation resistance shall be 10,000 megohms. TABLE III. Insertion loss versus frequency. Minimum no-load insertion loss (dB) in accordance with MIL-STD-220, at +25C. Dash number 50 MHz 100 MHz 200 MHz 500

14、 MHz 1-10 GHz 0001 50 65 70 70 70 Part or Identifying Number (PIN): M15733/46-0001 Marking: Filters shall be marked, as a minimum, with an abbreviated PIN as shown on figure 2. Full marking, in accordance with MIL-PRF-15733, shall be marked on the unit package. M1 57 33 46 00 01 FIGURE 2. Example of

15、 marking for the abbreviated PIN on the hex flats - expanded view. Application note: These nonhermetically sealed filters may be susceptible to moisture intrusion when subjected to repeated thermal cycling. If these items are to be utilized in applications enduring harsh environments, the user shoul

16、d consider placing them within hermetic enclosures. * Referenced documents. In addition to MIL-PRF-15733, this document also references the following: MIL-STD-202 MIL-STD-220 * Changes from previous issue. The margins of this specification sheet are marked with asterisks to indicate where changes fr

17、om the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the margina

18、l notations and relationship to the last previous issue. Custodians: Preparing activity: Navy - EC DLA - CC Air Force 11 DLA CC (Project 5915-2008-015) Review activities: Navy - AS, MC, OS Air Force - 19, 99 * NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-