DLA MIL-PRF-15733 38 L-2009 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL16.pdf

《DLA MIL-PRF-15733 38 L-2009 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL16.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-15733 38 L-2009 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL16.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5915 INCH-POUNDMIL-PRF-15733/38L 14 April 2009 SUPERSEDING MIL-PRF-15733/38K 27 February 2003 PERFORMANCE SPECIFICATION SHEET FILTERS, RADIO FREQUENCY INTERFERENCE, HERMETICALLY SEALED, STYLE FL16 * This specification sheet is approved for use by all Depart- ments and Agencies of the D

2、epartment of Defense. The complete requirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. * PINs M15733/38-0001, -0002, -0004, -0005, are inactive for new design as of 6 October 1980. PINs M15733/38-0003, -0006, and -0008 are inactive for

3、 new design as of 14 April 2009. For new design see table III. FIGURE 1. Filter and hardware dimensions and circuit diagrams. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/38L 2 Filter dimensions. A B C D E Dash number Min Max Min Max

4、 Min Max Min Max Min Max 0001 .290 (7.37) .310 (7.87) - .42 (10.7) .302 (7.67) .322 (8.18) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) 0002 .160 (4.06) .291 (7.39) - .415 (10.54) .180 (4.57) .200 (5.08) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) 0003 .530 (13.46) .550 (13.97) - .385 (9.78)

5、.177 (4.50) .197 (5.00) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) 0004 .160 (4.06) .180 (4.57) - .385 (9.78) .177 (4.50) .197 (5.00) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) 0005 .160 (4.06) .180 (4.57) - .385 (9.78) .177 (4.50) .197 (5.00) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83

6、) 0006 .160 (4.06) .291 (7.39) - .415 (10.54) .302 (7.67) .322 (8.18) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) 0007 .210 (5.33) .230 (5.84) - .385 (9.78) .302 (7.67) .322 (8.18) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) 0008 .160 (4.06) .180 (4.57) - .385 (9.78) .177 (4.50) .197 (5.00)

7、.100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) 0009 .290 (7.37) .310 (7.87) - .385 (9.78) .177 (4.50) .197 (5.00) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) 0010 .290 (7.37) .310 (7.87) - .385 (9.78) .302 (7.67) .322 (8.18) .100 (2.54) .190 (4.83) .100 (2.54) .190 (4.83) FIGURE 1. Filter and h

8、ardware dimensions and circuit diagrams - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/38L 3 Filter dimensions - Continued. F G H 1/ J Dash number +.010 -.015 Min Max .010 .010 Mounting thread 0001 .115 (2.92) .190 (4.83)

9、.210 (5.33) .060 (1.52) .080 (2.03) .250-28 UNF-2A 0002 .115 (2.92) .190 (4.83) .210 (5.33) .060 (1.52) .080 (2.03) .250-28 UNF-2A 0003 .115 (2.92) .190 (4.83) .210 (5.33) .060 (1.52) .080 (2.03) .250-28 UNF-2A 0004 .115 (2.92) .190 (4.83) .210 (5.33) .060 (1.52) .080 (2.03) .250-28 UNF-2A 0005 .115

10、 (2.92) .190 (4.83) .210 (5.33) .060 (1.52) .080 (2.03) .250-28 UNF-2A 0006 .115 (2.92) .190 (4.83) .210 (5.33) .060 (1.52) .080 (2.03) .250-28 UNF-2A 0007 .115 (2.92) .190 (4.83) .210 (5.33) .060 (1.52) .080 (2.03) .250-28 UNF-2A 0008 .115 (2.92) .190 (4.83) .210 (5.33) .060 (1.52) .080 (2.03) .250

11、-28 UNF-2A 0009 .115 (2.92) .190 (4.83) .210 (5.33) .060 (1.52) .080 (2.03) .250-28 UNF-2A 0010 .115 (2.92) .190 (4.83) .210 (5.33) .060 (1.52) .080 (2.03) .250-28 UNF-2A 1/ Optional slot may be supplied .050 (1.27) .010 (.25) inches by .070 (1.78) .010 (.25) inches. FIGURE 1. Filter and hardware di

12、mensions and circuit diagrams - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/38L 4 Hardware dimensions K L M N P Dash number Min Max Min Max Thread Min Max Min Max 0001 .302 (7.67) .322 (8.18) .085 (2.16) .095 (2.41) .250-

13、28 UNF-2B .395 (10.03) .408 (10.36) .010 (.25) .030 (.76) 0002 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .405 (10.29) .017 (.43) .027 (.69) 0003 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .405 (10.29) .017 (.43) .027 (.69) 0004 .307

14、(7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .405 (10.29) .017 (.43) .027 (.69) 0005 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .405 (10.29) .017 (.43) .027 (.69) 0006 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.0

15、3) .405 (10.29) .017 (.43) .027 (.69) 0007 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .405 (10.29) .017 (.43) .027 (.69) 0008 .307 (7.80) .317 (8.05) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .405 (10.29) .017 (.43) .027 (.69) 0009 .302 (7.67) .322 (8.18) .

16、088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .405 (10.29) .017 (.43) .027 (.69) 0010 .302 (7.67) .322 (8.18) .088 (2.24) .098 (2.49) .250-28 UNF-2B .395 (10.03) .405 (10.29) .017 (.43) .027 (.69) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only.

17、3. Circuit diagram is for information only. 4. All filters shall be supplied with mounting hardware. 5. Terminal thickness shall be .021 (0.53 mm)/.011 (0.28 mm). 6. Terminal identification. The case shall be marked at the threaded end of the filter, with the symbol “L” for dash numbers 0001, 0002,

18、0004, 0005, 0006, 0008, 0009, and 0010. FIGURE 1. Filter and hardware dimensions and circuit diagrams - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/38L 5 REQUIREMENTS: Dimensions and configuration: See figure 1. Weight: 5

19、 grams maximum. Case: Metal. Case and hardware finish: In accordance with MIL-PRF-15733. Pure tin finish is prohibited. Seal: Glass-to-metal. Terminals: Solderable (see figure 1). Operating temperature range: Dash 0001 through 0006, 0008, 0009, and 0010: -55C to +125C. Dash 0007: -55C to +85C Rated

20、voltage: See table I. Rated current: See table I. Seal: In accordance with MIL-PRF-15733. Capacitance to ground: Not specified. Temperature rise: +25C maximum. Insulation resistance: In accordance with MIL-PRF-15733 and the following: Test temperature: +25C. Test potential: Rated dc voltage or 100 v

21、olts dc whichever is less. Insulation resistance shall be not less than: Dash numbers Megohms 0001 500 0002 through 0007, 0009, and 0010 100 0008 1,000 Voltage drop: See table I. Insertion loss: In accordance with MIL-PRF-15733 and the following: At +25C: Shall be as specified in table I. At -55C an

22、d at the maximum operating temperature: Shall be as specified in table I except as follows: Up to 10 MHz: A degradation of 4 dB from the value specified in table I shall be allowed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/38L 6

23、Terminal strength: In accordance with MIL-PRF-15733 and method 211, MIL-STD-202; test condition A (pull): Applied force: 5 pounds. Salt atmosphere (corrosion): In accordance with MIL-PRF-15733 and method 101, MIL-STD-202; test condition A. Shock (specified pulse): In accordance with MIL-PRF-15733 an

24、d method 213, MIL-STD-202; test condition I (100g). Vibration, high frequency: In accordance with MIL-PRF-15733 and method 204, MIL-STD-202; test condition D (20g). Life: In accordance with MIL-PRF-15733 and method 108 of MIL-STD-202. Qualification inspection: Test condition D (1,000 hours). Group C

25、 inspection: Dash numbers Test condition 0001, 0002, 0004 through 0010 B (250 hours) 0003 D (1,000 hours) Part or Identifying Number (PIN): M15733/38- (dash number from table I). Marking: Marking shall be as follows: For dash numbers 0001, 0002, and 0004 through 0010, the filter shall be marked with

26、 the following minimum information: a. Military PIN. b. Source code. c. Date code. d. Terminal identification. Full marking in accordance with MIL-PRF-15733 shall be marked on the unit package. For dash number 0003, the filter shall be marked with full marking in accordance with MIL-PRF-15733. * Ext

27、ension of qualification: Initial qualification to MIL-PRF-15733/38 may be granted based on qualification to MIL-PRF-28861/1 or /3 or MIL-PRF-15733/49 as indicated in table II. Extension of qualification from MIL-PRF-28861/1 or /3 or MIL-PRF-15733/49 to MIL-PRF-15733/38 is permissible under the follo

28、wing provisions: a. The MIL-PRF-15733/38 part uses the same design and dielectric characteristics as the part upon which extension of qualification is based. b. The MIL-PRF-28861/1 or /3 or MIL-PRF-15733/49 qualification data verifies that the physical and electrical characteristics of the MIL-PRF-1

29、5733/38 parts are satisfied. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/38L 7 * TABLE I. Electrical characteristics. Dash number Voltage Minimum full load insertion loss (dB) in accordance with MIL-STD-220 at +25C 1/ Circuit Max cu

30、rrent (amps) DC volts AC 2/ Voltage drop (volts dc max) 30 KHz 150 KHz 300 KHz 1 MHz 10 MHz 100 MHz 1 GHz 10 GHz 0001 4/ L2 10 50 - .040 - - - 44 60 55 - - 0002 4/ L2 15 50 - .12 15 28 33 44 60 - 70 70 0003 4/ Pi 3 150 - .15 - 7 24 54 80 80 80 80 0004 4/ L2 10 50 - .08 15 28 33 44 60 - 70 - 0005 4/

31、L2 10 50 3/ - .08 15 28 33 44 60 - 70 - 0006 4/ L2 15 50 - .12 15 28 33 44 60 - 70 70 0007 Pi 15 50 - .09 70 dB from 420 MHz to 1.0 GHz, inclusive 0008 4/ L2 15 200 125 .12 - - - 6 25 - 60 - 0009 L2 15 250 125 .09 4 15 21 31 50 - 70 80 0010 L2 15 250 125 .09 4 15 21 31 50 - 70 80 1/ Full-load insert

32、ion loss measurements shall be performed over the frequency range of 100 kHz to 20 MHz inclusive. Measurements below or above this frequency range shall be performed at no-load. 2/ From dc to 400 Hz. 3/ Voltage rating at +125C: (Note - derated from 80 V dc at +85C). * 4/ Inactive for new design. * T

33、ABLE II. Extension of qualification. Qualification to MIL-PRF-28861 Will qualify MIL-PRF-15733/38 Qualification to MIL-PRF-15733/49 Will qualify MIL-PRF-15733/38 /01-001 -0002 -0006 -0004 /01-001 -0004 -0006 -0005 /01-001 -0005 /01-011 -0006 /01-009 /03-015 -0008 -0003 * TABLE III. Substitution data

34、 for new design. For new design use Inactive PIN Specification sheet PIN M15733/38-0001 M15733/38-0002 M15733/38-0003 M15733/38-0004 M15733/38-0005 M15733/38-0006 M15733/38-0008 MIL-PRF-28861/1 MIL-PRF-28861/1 MIL-PRF-28861/3 MIL-PRF-28861/1 MIL-PRF-28861/1 MIL-PRF-28861/1 MIL-PRF-28861/1 M28861/01-

35、011TB M28861/01-001TB M28861/03-015TB M28861/01-001TB M28861/01-001TB M28861/01-011TB M28861/01-009TB Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/38L 8 Referenced documents. In addition to MIL-PRF-15733, this document also reference

36、s the following: MIL-STD-202 MIL-STD-220 MIL-PRF-15733/49 MIL-PRF-28861/1 * MIL-PRF-28861/3 Changes from previous issue. The margins of this specification sheet are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Governme

37、nt assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activi

38、ty: Army - CR DLA - CC Navy - EC Air Force 85 (Project 5915-2009-001) DLA - CC Review activities: Army - AR, AT, AV Navy - AS, MC, OS, SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-