DLA MIL-PRF-10304 30 A (2)-2013 METERS ELECTRICAL INDICATING PANEL TYPE RUGGEDIZED MILLIAMMETER DC (FLUSH MOUNTING ROUND FLANGE 1 INCH) STYLES 05 06 AND 07.pdf

《DLA MIL-PRF-10304 30 A (2)-2013 METERS ELECTRICAL INDICATING PANEL TYPE RUGGEDIZED MILLIAMMETER DC (FLUSH MOUNTING ROUND FLANGE 1 INCH) STYLES 05 06 AND 07.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-10304 30 A (2)-2013 METERS ELECTRICAL INDICATING PANEL TYPE RUGGEDIZED MILLIAMMETER DC (FLUSH MOUNTING ROUND FLANGE 1 INCH) STYLES 05 06 AND 07.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 6625 PERFORMANCE SPECIFICATION SHEET METERS, ELECTRICAL INDICATING, PANEL TYPE, RUGGEDIZED: MILLIAMMETER, DC (FLUSH MOUNTING, ROUND FLANGE, 1 INCH), STYLES 05, 06, AND 07 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirement

2、s for acquiring the products described herein shall consist of this specification sheet and MIL-PRF-10304. FIGURE 1. Meter, panel type. INCH-POUND MIL-PRF-10304/30A w/AMENDMENT 2 28 August 2013 SUPERSEDING MIL-PRF-10304/30A w/AMENDMENT 1 18 January 2008 Provided by IHSNot for ResaleNo reproduction o

3、r networking permitted without license from IHS-,-,-MIL-PRF-10304/30A w/AMENDMENT 2 2 Inches mm Inches mm Inches mm .005 .13 .350 8.89 1.010 25.65 .015 .38 .375 9.53 1.187 30.15 .040 1.02 .500 12.70 1.250 31.75 .065 1.65 .850 21.59 1.251 31.78 .093 2.36 .901 22.89 .200 5.08 1.000 25.40 NOTES: 1. Dim

4、ensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerance is .015 (.38 mm). 4. Shroud design is optional. 5. Knurled edge required for mounting; optional for front flange. 6. The solder lug terminals shall accommodate wire of a diameter of

5、.065 (1.65 mm) and may accommodate up to a maximum diameter of .105 (2.67 mm). 7. The O-ring shall be in accordance with SAE AS28775 (table I, Dynamic or Static use), Part or Identifying Number (PIN) MS28775-213. FIGURE 1. Meter, panel type - Continued. REQUIREMENTS: (Readings expressed as a percent

6、 of full-scale value.) Dimensions and configuration: See figure 1. Weight: 4 ounces maximum. Case material: Metal or molded thermosetting plastic. Full-scale ranges: See table I. Scale: Pointer deflection: 90 degrees minimum. Length: 0.75 inch minimum. Power consumption: 100 milliamperes maximum. Po

7、sition influence: 3 percent. Accuracy: 3 percent. Overshoot: 50 percent maximum or damping factor of 2 minimum. Response time: 2.0 seconds. High temperature cycling: 4 percent. 4 percent permanent change. Temperature influence: 1 percent. Exposure to extreme temperatures: 8 percent. 3 percent perman

8、ent change. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-10304/30A w/AMENDMENT 2 3 Overload capacity: Momentary overload: 2 percent. Sustained overload: 2 percent temporary zero shift. 1 percent permanent zero shift. 2 percent permanent ch

9、ange. Dielectric withstanding voltage: 1, 000 volts rms. Supersession data: See table II. TABLE I. Full-scale ranges. Ammeters Milliamperes Zero left Zero Center 50 25-0-25 100 50-0-50 500 250-0-250 TABLE II. Supersession data. Superseded type designation New type designation Style 04 Style 07 MR04W

10、001DCMA MR07W001DCMAR MR04B001DCMA MR07B001DCMAR MR04F001DCMA MR07F001DCMAR MR04S001DCMA 1/MR07P001DCMAR Style 05 Style 05 MR05W001DCMA MR05W001DCMAR MR05B001DCMA MR05B001DCMAR MR05F001DCMA MR05F001DCMAR MR05S001DCMA 1/MR05P001DCMAR Style 06 Style 06 MR06W001DCMA MR06W001DCMAR MR06B001DCMA MR06B001D

11、CMAR MR06F001DCMA MR06F001DCMAR MR06S001DCMA 1/MR06P001DCMAR 1/ The color scheme code letter “S“ has been superseded by the code letter “P“. The type designations of all new units will carry the code letter “P“ (when applicable) to indicate that non-radioactive material has been used for phosphoresc

12、ent markings and pointer. Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidde

13、rs and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Referenced documents. In addition to MIL-PRF-10304, this document references the following: SAE AS28775 Provided by IHSNot for ResaleNo reproduction or n

14、etworking permitted without license from IHS-,-,-MIL-PRF-10304/30A w/AMENDMENT 2 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - SH Air Force - 99 (Project 6625-2013-018) DLA - CC Review activities: Army - AT, AV, CR4, MI Navy - MC NOTE: The activities listed above we

15、re interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-