DLA MIL-PRF-10304 23 D (2)-2013 METERS ELECTRICAL INDICATING PANEL TYPE RUGGEDIZED VOLTMETER AND AMMETER DC LONG SCALE (FLUSH MOUNTING ROUND FLANGE 4 5 INCH) STYLE 44.pdf
《DLA MIL-PRF-10304 23 D (2)-2013 METERS ELECTRICAL INDICATING PANEL TYPE RUGGEDIZED VOLTMETER AND AMMETER DC LONG SCALE (FLUSH MOUNTING ROUND FLANGE 4 5 INCH) STYLE 44.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-PRF-10304 23 D (2)-2013 METERS ELECTRICAL INDICATING PANEL TYPE RUGGEDIZED VOLTMETER AND AMMETER DC LONG SCALE (FLUSH MOUNTING ROUND FLANGE 4 5 INCH) STYLE 44.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 6625 PERFORMANCE SPECIFICATION SHEET METERS, ELECTRICAL INDICATING, PANEL TYPE, RUGGEDIZED: VOLTMETER AND AMMETER, DC LONG SCALE (FLUSH MOUNTING, ROUND FLANGE, 4.5 INCH), STYLE 44 This specification is approved for use by all Departments and Agencies of the Department of Defense. The re
2、quirements for acquiring the products described herein shall consist of this specification sheet and MIL-PRF-10304. FIGURE 1. Meter, panel type. INCH-POUND MIL-PRF-10304/23D w/AMENDMENT 2 28 August 2013 SUPERSEDING MIL-PRF-10304/23D w/AMENDMENT 1 18 January 2008 Provided by IHSNot for ResaleNo repro
3、duction or networking permitted without license from IHS-,-,-MIL-PRF-10304/23D w/AMENDMENT 2 2 Inches mm Inches mm Inches mm .005 .13 .250 6.35 2.450 62.23 .007 .18 .400 10.16 3.760 95.50 .010 .25 .500 12.70 3.785 96.14 .125 3.18 .510 12.95 4.125 104.78 .138 3.51 1.000 25.40 4.600 116.84 .150 3.81 1
4、.660 42.16 NOTES: 1. Dimensions are in inches. Unless otherwise specified, tolerances are .015 inch for two place (.XX), and .005 inch for three place (.XXX) dimensions. 2. Tolerance is 0.5 () degree on angles. 3. Metric equivalents are given for general information only. 4. Maximum projection from
5、front panel including mounting gaskets (if used). 5. Other forms of terminals, as specified in MIL-PRF-10304, are permitted. The specified minimum length applies to stud-type terminals only. Terminals shall be equally spaced, from each side of vertical centerline. FIGURE 1. Meter, panel type - Conti
6、nued. REQUIREMENTS: (Readings expressed as a percent of full-scale value.) Dimensions and configuration: See figure 1. Full-scale ranges: See table I. Scale: Length: 6 inches minimum. Pointer deflection: 250 degrees nominal. Position influence: 1 percent change for 60 degrees rotation from normal op
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILPRF1030423D22013METERSELECTRICALINDICATINGPANELTYPERUGGEDIZEDVOLTMETERANDAMMETERDCLONGSCALEFLUSHMOUNTINGROUNDFLANGE45INCHSTYLE44PDF

链接地址:http://www.mydoc123.com/p-692132.html