DLA MIL-PRF-1 810E-1999 ELECTRON TUBE CATHODE RAY TYPE 5AWP2.pdf

《DLA MIL-PRF-1 810E-1999 ELECTRON TUBE CATHODE RAY TYPE 5AWP2.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-1 810E-1999 ELECTRON TUBE CATHODE RAY TYPE 5AWP2.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-PRF-L/BLOE 999990b 2125954 955 m PERFORMANCE SPECIFICATION SHEET ELECTRON TUBE, CATHODE RAY TYPE 5AWP2 This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The requirements for acquiring the electron tube described herein shall consist of this do

2、cument and the latest issue of MIL-PRF-1. D-: Electrostatic deflection and focus, flat face, single beam, multiband post accelerator. DIMENSIONS AND PIN CONNECTIONS: See figure 1 ABSOLUTE RATINGS: Parameter: Unit: Maximum: Minimum: 1 5: Test conditions: 6.3 Ecl Ebl Eb2 Eb3 O, 1,700 3,850 16,500 I/ -

3、200 1 - I 1,000 I 4,500 Adjust 1 Focus I 2,300 1 10,300 1 .o See footnotes at end of table I +180 4.5 3r 10,000 GENERAL: Qualification: Required. 1 INCH-POUND I 17 SeDtember 1999 SUPERSEDING 17 March 1969 MIL-PRF-l/810E MIL-E-1 /81 OD FSC 5960 Provided by IHSNot for ResaleNo reproduction or networki

4、ng permitted without license from IHS-,-,-Inspection Conformance inspection I Voltage breakdown Voltage breakdown Gas “cross“ Screen and faceplate (electrostatic types) blemishes Modulation Spot position (eieciro- static deflection) Spot displacement Grid cutoff voltage Pattern distortion Grid No. 1

5、 leakage current Anode No. 1 leakage Anode No. 2 leakage (leakage) current current Conformation inspection Heater current Electrode current (anode No. i) Electrode current (cathode) Base alignment (electrostatic types) Side terminal alignment (electrostatic types) Side terminal and base alignment (e

6、lectrostatic types) Neck and base alignment (electrostatic types) -Angle between traces See footnotes at end of table. Method 5201 5201 5206 51 06 5223 5231 5231 5241 -_ 5251 5251 5251 1301 5201 5201 5101 5101 5101 5101 5101 MIL-PRF-l/810E TABLE I. Tesiina and insDection. Conditions b3 = 50 pA dc 9/

7、 b3 = 25 pA dc b3=50pAdc 41 -3D4, pin No. 5 -3D4 in No. 5 Acceptancr Level BI 0.65 0.65 0.65 0.65 0.65 0.65 0.65 0.65 0.65 0.65 0.65 0.65 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 2 - Symbol Unit Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-l/BlOE T

8、ABLE I. Testina and insoection - Continued. Inspection Conformance insoection, - Continued Stray light emission Screens Line width “A (conventional types) (electrostatic deflection) Line width “ES (electrostatic deflection) Focusing voltage at cutoff Focusing voltage at modulation condition Deflecti

9、on factor (ID2) Deflection factor (3D4) Heatercathode leakage Secureness of base, cap, or insert Conformation insDection Dart3 Life-tesi provisions Life-test end points Periodic-check tests Neck and bulb alignment (electrostatic deflection) Face tilt Cathode illumination Methoc 5216 5221 5226 5226 5

10、246 5246 5248 5248 5251 1101 Conditions Eb2 = 3,850 V dc; Eb3 = 16,500 V dc #b3 = 25 pA dc I b3 = 25 pA dc ;roup C; : = 500 hours (min) b3 = 12.5 FA dc; b3 = 18.75 pA dc, modulation -ne width “A -ne width “B“ ieater-cathode leakage Srid No. 1 leakage hode No. 1 leakage hode No. 2 leakage Acceptance

11、Level a/ 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 Symbol _ cbl Width Width Ebl Ebl DF DF Ihk _- _ AEcl Width Width Ihk IC1 Ibl lb2 Dla _-_ _ - _-_ 35 0.40 0.60 30 5 15 15 2.25 -_ 10x1 o-6 Unit _- cb mm mm V dc V dc J dc/inch J ddinch pA dc - _ V dc mm mm pA dc pA dc FA dc pA dc Inch _- fL 3 Provided

12、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Inspection Conformance insDection, - Continued Deflection-factor uniformity Deflection defocusing Magnetization Direct-interelectrode capacitance Pressure (implosion) Vi bration Method 5248 _ 5256 1331 1141 5111

13、 MIL- PR F- 1 /8 1 OE TABLE I. Testina and insDection - Continued. Conditions - 61 al gl to all k to all D1 to D2 D3 to D4 D1 to all D2 to all D3 to all D4 to all Acceptance Level 01 Symbol -I- _-_ _ _-_ cg 1 Ck C1 D2 C3D4 CDl CD2 CD3 CD4 -_ Width L Ma 2 1 :2 _ 5.0 4.1 2.2 1.5 5.4 6.1 4.5 3.9 _-_ 1

14、.o Unit Accelerator to final intensifier electrode voltage equally divided over the three intensifier electrodes by 25 megohm resistors connected between each intensifier and the accelerator. It is recommended that the deflection electrode circuit resistances be 1 megohm, or less, and approximately

15、equal, otherwise beam shift at high drives can be expected. Higher resistance values up to 5 megohms may be used for low-beam current operation. This tube is designed for optimum performance when operating at an Eb3/Eb2 ratio of 4.5. Operation at other ratios of Eb3/Eb2 may result in changes in defl

16、ection uniformity and pattern distortion. Accelerator power input (average) shall be limited to 6 watts. ID2 deflection factor shall be within 8 volts of 3D4. The useful scan in the ID2 and 3D4 directions is plus or minus 2 inches (50.8 mm) from tube face center. The ratio of the line width of a 4 i

17、nch (101.6 mm) long trace, adjusted for best center focus, to the line width measured on the faceplate axis when the trace is deflected perpendicularly plus or minus 2 inches (50.8 mm) from the face center by a balanced dc voltage, shall not be greater than the value specified. All portions of a ras

18、ter pattern, adjusted so its widest points just touch the sides of a 3.040 inch (77.22 mm) square, will fall within the area bounded by the 3.040 inch (T1.22 mm) square and an inscribed 2.9643 inch (75.18 mm) square. All other electrodes contained within the envelope shall be tied together. This tes

19、t to be performed at the conclusion of the holding period. This specification uses an acceptance zero (c = O) sampling plan, in accordance with MIL-PRF-1, Table 111. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I -+- C I D3 1 / REFERENCE LINE SE

20、E NOTE 2 t =-J MEDIUM SHELL DIHEPTAL 12 PIN BASE 1812-371 KEY- Dimensions Millimeters inches 1 2 3 4 5 7-12 14 Heater Cathode Grid No. 1 Internal connection Focusing electrode No connection Heater NOTES: 1. Minimum useful screen diameter. 2. Reference line, point where ring gauge 2.063 +.O01 1 inch

21、(52.40 +.O3 rnm) ID, ,500 inch (12.70 mm) long will stop. FIGURE 1. Outline drawina of electron tube tvDe 5AWP2. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Custodians: Navy - EC Air Force - 11 Any * CR DIA - CC M IL-P RF- 1 /81 OE Preparing activity: DU - CC (Project 5960-3558-02) Review activities: Any - CR4 Navy - AS, CG, MC, OS Air Force - 19,99 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-