DLA MIL-DTL-83733 10 C-2011 CONNECTORS ELECTRICAL RECEPTACLE PIN CONTACT MINIATURE RECTANGULAR TYPE RACK TO PANEL STAGGERED BUSHING MOUNTING ENVIRONMENT RESISTING 200掳C.pdf

《DLA MIL-DTL-83733 10 C-2011 CONNECTORS ELECTRICAL RECEPTACLE PIN CONTACT MINIATURE RECTANGULAR TYPE RACK TO PANEL STAGGERED BUSHING MOUNTING ENVIRONMENT RESISTING 200掳C.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83733 10 C-2011 CONNECTORS ELECTRICAL RECEPTACLE PIN CONTACT MINIATURE RECTANGULAR TYPE RACK TO PANEL STAGGERED BUSHING MOUNTING ENVIRONMENT RESISTING 200掳C.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECEPTACLE, PIN CONTACT, MINIATURE, RECTANGULAR TYPE, RACK TO PANEL, STAGGERED BUSHING MOUNTING, ENVIRONMENT RESISTING, 200C This specification is approved for use by all Departments and Agencies of the Department of Defense. The r

2、equirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83733. FIGURE 1. Dimensions and configurations. INCH-POUND MIL-DTL-83733/10C 31 January 2011 SUPERSEDING MIL-C-83733/10B (USAF) 10 December 1980 RECOMMENDED SCREW (NO.6) .138-32 UNC-2A FLH .3

3、8 LONG SEE NOTE 7 .223 .213 (4 PLACES) DIA L M .566 .558 1.170 1.146 SEE NOTE 3 N .286 .276 (FLANGE HOLE) DIA Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83733/10C 2 . Shell size L M N A 3.030 3.000 2.580 2.570 2.150 2.130 B 4.330 4.300 3

4、.880 3.870 3.450 3.430 Inches mm Inches mm Inches mm .138 3.51 .566 14.38 3.000 76.20 .213 5.41 1.146 29.11 3.030 76.96 .223 5.66 1.170 29.72 3.870 98.30 .276 7.01 2.130 54.10 3.880 98.55 .286 7.26 2,150 54.61 4.300 109.22 .38 9.7 2.570 65.28 4.330 109.98 .558 14.17 2.580 65.53 NOTES: 1. Dimensions

5、are in inches. 2. See MIL-DTL-83733 for interface and backend configuration requirements. 3. This receptacle mates with MIL-DTL-83733/12 plug. 4. For contacts see MIL-DTL-83733 and SAE AS39029/4, SAE AS39029/50 or SAE AS39029/58. 5. For insert arrangements see MIL-STD-1531 and MIL-STD-1532. 6. For f

6、ixed bushings see MS24700-2 7. Layout arrangements containing size 22D contacts shall not be used in this shell configuration. 8. Metric equivalents are given for information only and are based upon 1.00 inch equals 25.4 mm. FIGURE 1. Dimensions and configurations - Continued. Changes from previous

7、issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned t

8、o evaluate the requirements of this document based on the entire content irrespective of marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83733/10C 3 Referenced documents. In addi

9、tion to MIL-DTL-83733, this document references the following: MIL-DTL-83733/12 MIL-STD-1531 MIL-STD-1532 SAE AS39029/4 SAE AS39029/50 SAE AS39029/58 CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 85 DLA CC DLA - CC (Project 5935-2010-038) Review activity: Air Force 99 NOTE: The act

10、ivities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-