DLA MIL-DTL-83723 66 B-2009 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) PLUG THREADED COUPLING (PUSH-PULL QUICK-DISCONNECT WITHOUT LANYARD) CRIMP PIN CONTACT SERIES III .pdf

《DLA MIL-DTL-83723 66 B-2009 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) PLUG THREADED COUPLING (PUSH-PULL QUICK-DISCONNECT WITHOUT LANYARD) CRIMP PIN CONTACT SERIES III .pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83723 66 B-2009 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) PLUG THREADED COUPLING (PUSH-PULL QUICK-DISCONNECT WITHOUT LANYARD) CRIMP PIN CONTACT SERIES III .pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), PLUG, THREADED COUPLING, (PUSH-PULL, QUICK-DISCONNECT WITHOUT LANYARD), CRIMP PIN CONTACT, SERIES III, CLASSES A, G, M, R, T, W AND Z This specification is approved for use by all Departments and Agencies of the D

2、epartment of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Plug, threaded coupling, dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND MIL-DTL-83723/66B 29 June 2009 SUPERSEDING MIL-C-83723/66A (US

3、AF) 17 December 1991 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/66B 2 Inches mm Inches mm Inches mm Inches mm Inches mm .008 0.20 .045 1.14 .084 2.13 .144 3.66 .330 8.38 .015 0.38 .046 1.17 .090 2.29 .190 4.83 .400 10.16 .018 0.46

4、.061 1.55 .101 2.57 .198 5.03 .433 11.00 .020 0.51 .065 1.65 .106 2.69 .204 5.18 .479 12.17 .022 0.56 .065 1.65 .112 2.84 .221 5.61 .500 12.70 .031 0.79 .068 1.73 .125 3.18 .243 6.17 .510 12.95 .032 0.81 .069 1.75 .130 3.30 .290 7.37 1.18 29.97 .042 1.07 .070 1.78 .138 3.51 .320 8.13 FIGURE 1. Plug,

5、 threaded coupling, dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/66B 3 Shell size A B C D E F thread G H 8 .704 (17.88) .290 (7.37) .470 (11.94) .370 (9.40) .305 (7.75) .500-20 UNF-2A .437 (

6、11.10) .294 (7.47) 10 .829 (21.06) .388 (9.86) .600 (15.24) .497 (12.62) .405 (10.29) .625-24 UNEF-2A .572 (14.53) .428 (10.87) 12 1.016 (25.81) .588 (14.94) .724 (18.39) .613 (15.57) .531 (13.49) .750-20 UNEF-2A .687 (17.45) .598 (15.19) 14 1.079 (27.41) .627 (15.93) .849 (21.56) .738 (18.75) .665

7、(16.89) .875-20 UNEF-2A .812 (20.62) .667 (16.94) 16 1.204 (30.58) .772 (19.61) .974 (24.74) .863 (21.92) .790 (20.07) 1.000-20 UNEF-2A .937 (23.80) .794 (20.17) 18 1.345 (34.16) .860 (21.84) 1.030 (26.16) .919 (23.34) .869 (22.07) 1.0625-18 UNEF-2A .992 (25.20) .900 (22.86) 20 1.470 (37.34) .985 (2

8、5.02) 1.154 (29.31) 1.044 (26.52) .994 (25.25) 1.1875-18 UNEF-2A 1.117 (28.37) 1.025 (26.04) 22 1.595 (40.51) 1.110 (28.19) 1.279 (32.49) 1.169 (29.69) 1.119 (28.42) 1.3125-18 UNEF-2A 1.242 (31.55) 1.150 (29.21) 24 1.720 (43.69) 1.235 (31.37) 1.404 (35.66) 1.294 (32.87) 1.244 (31.60) 1.4375-18 UNEF-

9、2A 1.367 (34.72) 1.275 (32.39) Shell size J K M 8 .405 (10.29) .396 (10.06) .612 (15.54) 1.095 (27.81) 10 .526 (13.36) .517 (13.13) .737 (18.72) 1.240 (31.50) 12 .696 (17.68) .687 (17.45) .925 (23.50) 1.432 (36.37) 14 .765 (19.43) .756 (19.20) .987 (25.07) 1.490 (37.85) 16 .892 (22.66) .883 (22.43)

10、1.112 (28.24) 1.711 (43.46) 18 .998 (25.35) .989 (25.12) 1.237 (31.42) 1.815 (46.10) 20 1.123 (28.52) 1.114 (28.30) 1.362 (34.59) 1.962 (49.83) 22 1.248 (31.70) 1.239 (31.47) 1.487 (37.77) 2.070 (52.58) 24 1.373 (34.87) 1.364 (34.65) 1.612 (40.94) 2.195 (55.75) FIGURE 1. Plug, threaded coupling, dim

11、ensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/66B 4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. Metric equivalents are in parentheses. 3. Unless oth

12、erwise specified, tolerances are .010 (0.25) for two place decimals, .005 (0.13) for three place decimals, and 1oand 30 for angular dimensions. 4. The dimensions showing the relationship of the coupling ring to the shell apply only when the coupling ring is in the full forward position. 5. This quic

13、k-disconnect connector plug is intended to be used with series III threaded coupling receptacles MIL-DTL-83723/82 and MIL-DTL-83723/84, with adapter MIL-DTL-83723/70 permanently attached to the receptacle. 6. Coupling of the quick-disconnect plug connector is to be accomplished by a straight axial p

14、ush with no cocking of the coupling mechanism. 7. Uncoupling of the quick-disconnect plug connector is to be accomplished by a straight axial pull on the outer coupling ring. 8. See table I for contact cavities requiring this dimension. FIGURE 1. Plug, threaded coupling, dimensions and configuration

15、s - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/66B 5 Shell size P P1 P2 P3 P4 R R1 8 1.457 (37.01) 1.869 (47.47) 2.018 (51.26) 5.838 (148.29) 1.848 (46.94) .830 (21.08) 4.585 (116.46) 10 1.457 (37.01) 1.979 (50.27) 2.100

16、 (53.34) 6.528 (165.81) 1.888 (47.96) .880 (22.35) 5.390 (136.91) 12 1.457 (37.01) 2.124 (53.95) 2.293 (58.24) 7.348 (186.64) 1.928 (48.97) .950 (24.13) 6.330 (160.78) 14 1.457 (37.01) 2.124 (53.95) 2.353 (59.77) 7.348 (186.64) 1.928 (48.97) 1.010 (25.65) 6.330 (160.78) 16 1.457 (37.01) 2.229 (56.62

17、) 2.502 (63.55) 8.068 (204.93) 2.028 (51.51) 1.070 (27.18) 6.710 (170.43) 18 1.457 (37.01) 2.474 (62.84) 2.614 (66.40) 8.068 (204.93) 2.028 (51.51) 1.130 (28.70) 6.710 (170.43) 20 1.457 (37.01) 2.604 (66.14) 2.739 (69.57) 9.068 (230.33) 2.148 (54.56) 1.190 (30.23) 7.740 (196.60) 22 1.457 (37.01) 2.7

18、29 (69.32) 2.864 (72.75) 9.068 (230.33) 2.148 (54.56) 1.260 (32.00) 7.740 (196.60) 24 1.457 (37.01) 2.854 (72.49) 2.989 (75.92) 9.068 (230.33) 2.228 (56.59) 1.320 (33.53) 8.030 (203.96) FIGURE 2. Plug and backshell assembly, dimensions and configurations. Provided by IHSNot for ResaleNo reproduction

19、 or networking permitted without license from IHS-,-,-MIL-DTL-83723/66B 6 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. Metric equivalents are in parentheses. 3. Unless otherwise specified, tolerances are .010 (0.25) for two place decimals, .005 (0.13) for

20、 three place decimals, and 1o30 for angular dimensions. FIGURE 2. Plug and backshell assembly, dimensions and configurations Continued. REQUIREMENTS: Dimensions and configurations: See figures 1 and 2. For insert arrangements, see MIL-STD-1554 and table I. TABLE I. Inserts requiring reduced diameter

21、s for raised seal barriers on the outer row of the contact cavities. Shell size Insert arrangements Contact cavities 8 03 1, 2, 3 10 06 1, 2, 3, 4, 5, 6 For connector accessories: See SAE-AS85049 and MIL-C-83723/16. Unless otherwise specified in the purchase order, the following components shall be

22、furnished with the connector: a. Contacts in accordance with SAE-AS39029 shall be furnished with the connector. Spare contacts for each size contact are required. The total quantity of spare contacts shall be 10 percent or 1, whichever is greater, of the total number of each size contact required. b

23、. Grommet seal plugs in accordance with MS27488 shall be furnished with the connector. Total quantity shall be 15 percent of each contact size or 3, whichever is greater. c. Contact extraction tools in accordance with MIL-I-81969 shall be included in the connector package. Connector assembly shall i

24、nclude a backshell (see SAE-AS85049 and MIL-C-83723/16) to ensure compliance with moisture sealing requirements. The coupling mechanism of the connector plug shall withstand a minimum tensile load of 100 lb (45.36 kg) minimum. Load shall be applied to rear accessory hardware in a straight axial dire

25、ction. The quick-disconnect connector plug shall meet the vibration and shock requirements in accordance with MIL-DTL-83723 and the coupling mechanism shall maintain the plug and receptacle in a locked condition. The tensile force required to unlock the coupling mechanism shall be 5 lb (2.27 kg) min

26、imum and 20 lb (9.07 kg) maximum. The locking mechanism shall meet the performance requirements of MIL-DTL-83723. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/66B 7 Part or Identifying Number (PIN) example: M83723/ 66 W 22 55 N Milit

27、ary designator Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition t

28、o MIL-DTL-83723, this document references the following: MIL-STD-1554 MS27488 MIL-I-81969 MIL-C-83723/16 MIL-DTL-83723/70 MIL-DTL-83723/82 MIL-DTL-83723/84 SAE-AS39029 SAE-AS85049 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 (Project 5935-2008-102)

29、DLA - CC Review activities: Air Force 70, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-