DLA MIL-DTL-55116 9 C-2013 CONNECTOR RECEPTACLE FIVE-PIN AUDIO SOLDER CUP SPRING TERMINALS PANEL MOUNT U-183 TYPE.pdf

《DLA MIL-DTL-55116 9 C-2013 CONNECTOR RECEPTACLE FIVE-PIN AUDIO SOLDER CUP SPRING TERMINALS PANEL MOUNT U-183 TYPE.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-55116 9 C-2013 CONNECTOR RECEPTACLE FIVE-PIN AUDIO SOLDER CUP SPRING TERMINALS PANEL MOUNT U-183 TYPE.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-DTL-55116/9C 01 August 2013 SUPERSEDING MIL-DTL-55116/9B 11 December 2000 DETAIL SPECIFICATION SHEET CONNECTOR, RECEPTACLE, FIVE-PIN AUDIO, SOLDER CUP SPRING TERMINALS, PANEL MOUNT, U-183 TYPE This specification is approved for use by all Departments and Agencies of the Department of Defense. T

2、he requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55116. FIGURE 1. Connector, receptacle, five-pin audio, panel mount. AMSC N/A FSC 5935 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

3、 IHS-,-,-MIL-DTL-55116/9C 2 FIGURE 1. Connector, receptacle, five-pin audio, panel mount - Continued.DETAIL A SOLDER TERMINAL VISUAL ALIGNMENT INDICATOR (ORANGE) 4 PLACES Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55116/9C 3 J-SLOT DETAI

4、L (3 PLACES) FIGURE 1. Connector, receptacle, five-pin audio, panel mount - Continued. REQUIREMENTS: Contact retention: This test is only applicable when force is applied to the terminal end, tending to push the terminal into the connector body. Part or Identifying Number (PIN): M55116/9-0. Dimensio

5、ns and configuration: See figure 1. Reference documents. This document references MIL-DTL-55116. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Gove

6、rnment assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Inches mm Inches mm .002

7、 0.05 .217 5.51 .005 0.13 .223 5.66 .007 0.18 .235 5.97 .010 0.25 .265 6.73 .012 0.30 .280 7.11 .015 0.38 .282 7.16 .016 0.41 .445 11.30 .020 0.51 .450 11.43 .027 0.69 .455 11.56 .029 0.74 .456 11.58 .030 0.76 .526 13.36 .037 0.94 .528 13.41 .040 1.02 .549 13.94 .046 1.17 .553 14.05 .050 1.27 .590 1

8、4.99 .054 1.37 .594 15.09 .056 1.42 .627 15.93 .058 1.47 .631 16.03 .060 1.52 .640 16.26 .064 1.63 .650 16.51 .065 1.65 .665 16.89 .069 1.75 .675 17.15 .074 1.88 .722 18.34 .075 1.91 .732 18.59 .086 2.18 .740 18.80 .088 2.24 .748 19.00 .090 2.29 .750 19.05 .0935 2.375 .782 19.86 .0965 2.451 .792 20.

9、12 .100 2.54 .905 22.99 .105 2.67 .915 23.24 .125 3.18 .953 24.21 .135 3.43 .963 24.46 .150 3.81 .97 24.6 .160 4.06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55116/9C 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA -

10、 CC DLA - CC (Project 5935-2013-201) Review activity: Army MI NOTE: The activities listed above were interested in this document as of the date of this document. Since organization and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-