DLA MIL-DTL-5423 14 G-2009 BOOT DUST AND WATER SEAL TYPE D (FOR LEVER OPERATED CIRCUIT BREAKERS) STYLE 2 (PANEL MOUNTED COMPLETE WITH MOUNTING FRAME).pdf

《DLA MIL-DTL-5423 14 G-2009 BOOT DUST AND WATER SEAL TYPE D (FOR LEVER OPERATED CIRCUIT BREAKERS) STYLE 2 (PANEL MOUNTED COMPLETE WITH MOUNTING FRAME).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-5423 14 G-2009 BOOT DUST AND WATER SEAL TYPE D (FOR LEVER OPERATED CIRCUIT BREAKERS) STYLE 2 (PANEL MOUNTED COMPLETE WITH MOUNTING FRAME).pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND MIL-DTL-5423/14G 17 February 2009 SUPERSEDING MIL-DTL-5423/14F 4 February 2008 DETAIL SPECIFICATION SHEET BOOT, DUST AND WATER SEAL, TYPE D (FOR LEVER OPERATED CIRCUIT BREAKERS), STYLE 2 (PANEL MOUNTED COMPLETE WITH MOUNTING FRAME) This specification sheet is approved for use by all Depar

2、tments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5423. FIGURE 1. Dimensions and configuration boots type D, style 1. AMSC N/A FSC 5930 Provided by IHSNot for ResaleNo reproduction or ne

3、tworking permitted without license from IHS-,-,-MIL-DTL-5423/14G 2 FIGURE 1. Dimensions and configuration boots type D, style 1 Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5423/14G 3 “0“- RING-Inches mm Inches mm Inches mm Inch

4、es mm .031 0.79 .921 23.39 1.593 40.46 2.625 66.68 .05 1.3 1.000 25.40 1.781 45.24 2.656 67.46 .063 1.60 1.093 27.76 1.875 47.63 2.750 69.85 .093 2.36 1.109 28.17 2.000 50.80 2.906 73.81 .12 3.0 1.125 28.58 2.062 52.37 3.062 77.77 .16 4.1 1.343 34.11 2.125 53.98 3.093 78.56 .19 4.8 1.375 34.93 2.218

5、 56.34 3.156 80.16 .250 6.35 1.38 35.1 2.25 57.2 3.500 88.90 .375 9.53 1.44 36.6 2.26 57.4 3.625 92.08 .843 21.41 1.46 37.1 2.31 58.7 3.656 92.86 .875 22.23 1.500 38.10 2.32 58.9 3.718 94.45 .91 23.1 1.53 38.9 2.343 59.51 3.937 100.11 4.312 109.534.812 122.22 NOTES: 1. Dimensions are in inches. 2. M

6、etric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .02 (.51mm) for two place decimals and .031 (.79 mm) for three place decimals. 4. The number of mounting screws shall be supplied as indicated. 5. Edges shall be smooth and free from burrs. 6. Alt

7、ernative base metals and protective finishes, as approved by the qualifying activity, may be utilized for frame materials. FIGURE 1. Dimensions and configuration boots type D, style 1 Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL

8、-5423/14G 4 REQUIREMENTS Dimensions and configuration: See figure 1. Silicon rubber: Grade 50, transparent. Splashproof: In accordance with MIL-STD-108, table I. Endurance (with applicable circuit breaker): 10,000 operations, see MIL-DTL-5423. Minute cracks after life test, which do not permit leaka

9、ge, shall not be cause for rejection. Part or Identifying Number (PIN): See tables I and II. Table I. Part or identifying numbers (PIN). PINs 1/ Dimensions .031 M5423/14- A L1 L2 W1 W2 H L3 L4 W3 01 2.750 2.125 3.937 1.500 1.093 1.109 2.25 None None 02 3.062 2.000 3.625 2.062 1.343 1.125 2.31 None N

10、one 03 2.750 2.000 3.718 3.656 3.156 .921 2.25 None None 04 3.062 2.000 3.500 4.812 4.312 1.000 2.31 None None 05 05T 2.062 1.875 2.625 1.375 .843 .875 None 1.44 .375 06 06T 2.062 1.875 2.656 2.218 1.593 .875 None 1.44 1.00 07 07T 2.062 1.875 2.656 2.906 2.343 .875 None 1.44 1.00 08 08T 2.062 1.781

11、2.656 3.718 3.093 .875 None 1.44 1.00 1/ M5423/14-05T through -08T includes a trigger element. Table II. Mounting and hardware information. Mounting holes 1/ Panel cutout Location Markings PINs 1/ M5423/14- Number of screws B B1 B2 B3 Top side Bottom side Y 01 2 yes none none none ON none 1.00 (25.4

12、) 02 4 2/ none .500 (12.70) none none none 1.25 (31.8) 03 6 yes 1.031 (26.19) none none ON none 3.06 (77.7) 04 12 none .500 (12.70) 1.000 (25.40) 2.000 (50.80) ON none 4.25 (108.0) 05 05T 2 yes none none none ON none .76 (19.3) 06 06T 4 none .375 (9.53) none none ON none 1.53 (38.9) 07 07T 6 yes .75

13、0 (19.05) none none ON none 2.28 (57.9) 08 08T 8 none .375 (9.53) 1.125 (28.58) none ON OFF 3.06 (77.7) 1/ M5423/14-05T through -08T includes a trigger element. 2 Screws shall be 8-32 UNC X .38 long (9.6 mm), slotted pan head. Qualification: First Article Testing in accordance with MIL-DTL-5423. Pro

14、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5423/14G 5 Reference Documents MIL-DTL-5423 MIL-STD-108 ASTM-A493 The margins of this specification are marked with vertical lines to indicate where modifications were made. This was done as a conv

15、enience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Custodians: Preparing activity: Army - CR D

16、LA - CC Navy - AS Air Force - 85 (Project 5930-2008-070) DLA - CC Review activities: Army - AT, AV, CR4 Navy - CG, MC, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-