DLA MIL-DTL-52471 8 B-2008 HOSE ASSEMBLIES RUBBER HYDRAULIC PRESSURE-TYPE TYPE 100RE.pdf
《DLA MIL-DTL-52471 8 B-2008 HOSE ASSEMBLIES RUBBER HYDRAULIC PRESSURE-TYPE TYPE 100RE.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-DTL-52471 8 B-2008 HOSE ASSEMBLIES RUBBER HYDRAULIC PRESSURE-TYPE TYPE 100RE.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、INCH-POUNDMIL-DTL-52471/8B 4 December 2008 SUPERSEDING MIL-DTL-52471/8A 27 April 1998 DETAIL SPECIFICATION SHEET HOSE ASSEMBLIES, RUBBER: HYDRAULIC PRESSURE-TYPE; TYPE 100RE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acqu
2、iring the product described herein shall consist of this specification sheet and MIL-DTL-52471. FIGURE 1. Hose assembly, fitting identification. Operating pressure. Hose assembly operating pressures are shown in table I. TABLE I. Hose operating pressure. 1/ 2/ Hose ID Maximum operating pressure Mini
3、mum burst pressure Hose ID dash number Inch fraction Inch decimal mm psi MPa psi MPa -8 1/2 .500 12.70 7500 51.7 30,000 206.9 -12 3/4 .750 19.05 6250 43.1 25,000 172.4 -16 1 1.000 25.40 5000 34.5 20,000 137.9 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. Hose ass
4、embly code number. The purpose of this slash sheet is to provide hose assembly code numbers for determining the hose diameter, fitting X, fitting Y, and bend angles (when applicable) as shown in tables II through IV. The bend angles are called “style codes” and consist of hose assembly styles as exp
5、lained in MIL-DTL-52471. AMSC N/A FSC 4720 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-52471/8B 2 TABLE II. 1/2-inch hose assemblies. Fitting X (figure 1) Fitting Y (figure 1) Hose ID Inch fraction Inch decimal (mm) Hose PIN 1/ PIN Bend a
6、ngle 2/ PIN Bend angle 2/ Assembly code number 3/ M52525/31-08-08 0 C001 M52525/32-08-08 45 C002 M52525/31-08-08 0 M52525/33-08-08 90 C003 M52525/32-08-08 45 C004 M52525/32-08-08 45 M52525/33-08-08 90 C005 M52525/33-08-08 90 C006 M52525/33-08-08 90 M52525/34-08-08 0 C007 M52525/35-08-08 45 C008 M525
7、25/34-08-08 0 M52525/36-08-08 90 C009 M52525/35-08-08 45 C010 M52525/35-08-08 45 M52525/36-08-08 90 C011 1/2 .500 (12.70) M52471/7-8 M52525/36-08-08 90 M52525/36-08-08 90 C012 1/ Part or Identifying Number (PIN). 2/ Reference MIL-DTL-52471 for hose assembly bend angles and displacement angles used i
8、n the PIN. 3/ A suffix indicating plating finish shall be specified with the assembly code number, see table V. TABLE III. 3/4-inch hose assemblies. Fitting X (figure 1) Fitting Y (figure 1) Hose ID Inch fraction Inch decimal (mm) Hose PIN PIN Bend angle 1/ PIN Bend angle 1/ Assembly code number 2/
9、M52525/31-12-12 0 C101 M52525/32-12-12 45 C102 M52525/33-12-12 90 C103 M52525/31-12-12 0 M52525/34-12-12 0 C107 M52525/35-12-12 45 C108 M52525/34-12-12 0 M52525/36-12-12 90 C109 M52525/35-12-12 45 C110 M52525/35-12-12 45 M52525/36-12-12 90 C111 3/4 .750 (19.05) M52471/7-12 M52525/36-12-12 90 M52525/
10、36-12-12 90 C112 1/ Reference MIL-DTL-52471 for hose assembly bend angles and displacement angles used in the PIN. 2/ A suffix indicating plating finish shall be specified with the assembly code number, see table V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
11、 from IHS-,-,-MIL-DTL-52471/8B 3 TABLE IV. 1 inch hose assemblies. Hose Fitting X (figure 1) Fitting Y (figure 1) Hose ID Inch fraction Inch decimal (mm) PIN PIN Bend angle1/ PIN Bend angle 1/ Assemblycode number 2/ M52525/31-16-16 0 C201 M52525/32-16-16 45 C202 M52525/33-16-16 90 C203 M52525/31-16-
12、16 0 M52525/34-16-16 0 C207 M52525/35-16-16 45 C208 M52525/34-16-16 0 M52525/36-16-16 90 C209 M52525/35-16-16 45 C210 M52525/35-16-16 45 M52525/36-16-16 90 C211 1 1.000 25.40 M52471/7-16 M52525/36-16-16 90 M52525/36-16-16 90 C212 1/ Reference MIL-DTL-52471 for hose assembly bend angles and displacem
13、ent angles used in the PIN. 2/ A suffix indicating plating finish shall be specified with the assembly code number, see table V. Fitting materials and finishes shall be in accordance with MIL-DTL-52525, material and plating designators are specified in table V. Provided by IHSNot for ResaleNo reprod
14、uction or networking permitted without license from IHS-,-,-MIL-DTL-52471/8B 4 TABLE V. Material and finish identification codes. 1/ 2/ PIN code material/plating finish Material Plating finish A Anodize in accordance with MIL-A-8625, type II. AN Anodize in accordance with MIL-A-8625, type II and NAV
15、AIR trivalent chromium pretreatment (TCP) in accordance with MIL-DTL-81706, type 2, class A. BN Aluminum alloy 6061 or 7075 Bare aluminum with NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. C Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, typ
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILDTL524718B2008HOSEASSEMBLIESRUBBERHYDRAULICPRESSURETYPETYPE100REPDF

链接地址:http://www.mydoc123.com/p-690897.html