DLA MIL-DTL-44031 E-2011 CLOTH CAMOUFLAGE PATTERN COTTON AND NYLON.pdf

《DLA MIL-DTL-44031 E-2011 CLOTH CAMOUFLAGE PATTERN COTTON AND NYLON.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-44031 E-2011 CLOTH CAMOUFLAGE PATTERN COTTON AND NYLON.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-DTL-44031E 26 January 2011 SUPERSEDING MIL-C-44031D 22 August 1989 DETAIL SPECIFICATION CLOTH, CAMOUFLAGE PATTERN: COTTON AND NYLON This specification is approved for use by all Departments and Agencies of the Department of Defense (DoD). 1. SCOPE 1.1 Scope. This specification covers the follow

2、ing classes as specified (see 6.2). 1.2 Classification. The cloth is furnished in the following classes as specified (see 6.2). Class 1 - Camouflage Printed (Woodland Camouflage Print) Class 2 - Camouflage Printed and Quarpel Treated (Woodland Camouflage Print) Class 3 - Universal Camouflage Print (

3、UCP), Static Dissipative Fiber Class 4 - Universal Camouflage Print (UCP), Water Repellent Treated Class 5 - Woodland Camouflage Print, Static Dissipative Fiber Class 6 - Universal Camouflage Print (UCP) Class 7 - Operation Enduring Freedom Camouflage Pattern (OCP) (see 6.10) Class 8 - Operation End

4、uring Freedom Camouflage Pattern (OCP), Water Repellent Treated (see 6.10) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or re

5、commended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed.

6、AMSC N/A FSC 8305 INCH-POUND Comments, suggestions, or questions on this document should be addressed to: Attn: DLA Troop Support Standardization Team, 700 Robbins Avenue, Philadelphia, PA 19111-5096. Since contact information can change, you may want to verify the currency of the address informatio

7、n using Acquisition Streamlining and Standardization Information System (ASSIST) online database https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44031E 2 2.2 Government documents. 2.2.1 Specifications, standards,

8、and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. FEDERAL STANDARDS FED-STD-4 - Glossary of Fabric Imperfections

9、 (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government doc

10、uments, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation or contract. COMMERCIAL ITEM DESCRIPTIONS A-A-50199 - Thread, Polyester Core, Cotton or Polyester-Covered (Copies of these docume

11、nts are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Order Desk, Building 4D, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) DRAWINGS 2-1-1516 - Woodland Camouflage Pattern 2-1-2519 - Universal Camouflage Pattern (Copies of drawings are avai

12、lable from the Department of the Army, Natick Soldier Research Development and Engineering Center, Kansas St., Natick MA 01760, ATTN: RDNS-WPW-C) FEDERAL TRADE COMMISSION Rules and Regulations Under the Textile Fiber Products Identification Act (Copies are available online at http:/www.ftc.gov or fr

13、om the Federal Trade Commission, 600 Pennsylvania Avenue, N.W., Washington, DC 20580-0001.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitat

14、ion or contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44031E 3 AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC Test Method 8 - Colorfastness to Crocking: AATCC Crockmeter Method AATCC Test Method 15 - Colorfast

15、ness to Perspiration AATCC Test Method 16 - Colorfastness to Light AATCC Test Method 20 - Fiber Analysis: Qualitative AATCC Test Method 20A - Fiber Analysis: Quantitative AATCC Test Method 22 - Water Repellency Spray Test AATCC Test Method 61 - Colorfastness to Laundering: Accelerated AATCC Test Met

16、hod 70 - Water Repellency: Tumble jar Dynamic Absorption Test AATCC Test Method 81 - pH of the Water-Extract from Wet Processed Textiles AATCC Test Method 96 - Dimensional Changes in Commercial Laundering of Woven and Knitted Fabrics Except Wool AATCC Test Method 118 - Oil Repellency: Hydrocarbon Re

17、sistance Test AATCC Test Method 127 - Water Resistance: Hydrostatic Pressure Test AATCC Evaluation Procedure 1 - Gray Scale for Color Change AATCC Evaluation Procedure 2 - Gray Scale for Staining AATCC Evaluation Procedure 8 - AATCC 9-Step Chromatic Transference Scale AATCC Evaluation Procedure 9 -

18、Visual Assessment of Color Difference of Textiles (Copies of these documents are available online at http:/www.aatcc.org or from the American Association of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709-2215.) AMERICAN SOCIETY FOR QUALITY ANSI/ASQ Z1.4 - Sampling P

19、rocedures and Tables for Inspection by Attributes (Copies are available online at http:/www.asq.org or from the American Society for Quality Control, 600 North Plankinton Avenue, Milwaukee, WI 53203.) ASTM INTERNATIONAL ASTM D 276 - Standard Test Methods for Identification of Fibers in Textiles ASTM

20、 D 629 - Standard Test Methods for Quantitative Analysis of Textiles ASTM D 737 - Standard Test Method for Air Permeability of Textile Fabrics ASTM D 1424 - Standard Test Method for Tearing Strength of Fabrics by Falling- Pendulum (Elmendorf) Apparatus ASTM D 1683 - Standard Test Method for Failure

21、in Sewn Seams of Woven Fabrics ASTM D 3775 - Standard Test Method for Warp (End) and Filling (Pick) Count of Woven Fabrics ASTM D 3776 - Standard Test Method for Mass per Unit Area (Weight) of Fabric ASTM D 5034 - Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Tes

22、t) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44031E 4 (Copies of these documents are available on line at http:/www.astm.org or from the ASTM INTERNATIONAL, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959.) OTHER

23、PUBLICATIONS Principles and Methods of Toxicology, Repeat Insult Patch Test - Modified Draize Procedure - (fourth edition) A Wallace Hayes (editor), pp 1057 1060, 2001. (Copies are available online at http:/www.taylorandfrancis.co.uk/ or from Taylor and Francis, 325 Chestnut Street, Philadelphia PA

24、19106 .) Sears Roebuck and Co. Sears Fabric Defect Replica Scales (Copies available from Sears Roebuck and Co., “Fabric Defect Replica Kit” Dept 817 (ATTN: FC 554B), 3333 Beverly Road, HG, FC568B, Hoffman Estates, IL 60179). For information call (847-286-8952.) 2.4 Order of precedence. Unless otherw

25、ise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

26、3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.2. 3.2 Standard sample. The finished cloth shall match the standard sample for shade and appearance and shall, unless otherwise indicated, be equal to or better t

27、han the standard sample with respect to all characteristics for which the standard sample is referenced (see 6.4). 3.3 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided th

28、at the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.4 Materials. 3.4.1 Cotton. The cotton shall be carded. 3.4.2 Nylon. The nylon shall be first quality, high tenacity, semi-dull staple having a nominal cut length

29、of 1-1/2 inches and a round cross section with a nominal denier of 2.25 to 2.50. No form of nylon waste shall be used, such as undrawn fiber, mixtures of deniers, lusters or cross sections, and waste from any stage of fiber production: whether drawn, un-drawn, or mixed or garneted fiber. Testing sha

30、ll be as specified in 4.4.3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44031E 5 3.4.3 Static dissipative fiber (Class 3 and Class 5). The fiber shall have a carbon core and nylon sheath and shall be 3 to 3.8 nominal denier per filament

31、and a cut length of 1-1/2 to 2 inches in staple length (see 6.8). 3.4.4 Yarns. The warp and filling yarn shall be singles made from a blend of 50 ( 5) percent nylon and the remaining percentage cotton based on the dry weight of the desized cloth when tested as specified in 4.4.3. The yarn for the Cl

32、ass 3 and Class 5 shall contain 2 percent static dissipative fiber. 3.5 Color. 3.5.1 Classes 1, 2 and 5 Woodland Camouflage. The cloth shall be dyed to a ground shade either matching or approximating Light Green 354 and then shall be overprinted with the camouflage pattern by roller or screen printi

33、ng. When the ground shade is dyed to match Light Green 354, the remaining colors shall be obtained by subsequent printing using three rollers or screens, as appropriate for the Dark Green 355, Brown 356, and Black 357 areas of the pattern. When the ground shade is dyed to approximate Light Green 354

34、, all four colors of the camouflage pattern shall be obtained by subsequent printing using four rollers or screens to match all four colors. Resin bonded pigments shall not be used (see 6.5). 3.5.2 Classes 3, 4 and 6 Universal Camouflage Pattern (UCP). The cloth shall be dyed to a ground shade eithe

35、r matching or approximating Desert Sand 500 and then shall be overprinted with the camouflage pattern by roller or screen printing. When the ground shade is dyed to match Desert Sand 500, the remaining colors shall be obtained by subsequent printing using two rollers or screens, as appropriate for t

36、he Urban Gray 501 and Foliage Green 502 areas of the pattern. When the ground shade is dyed to approximate Desert Sand 500 all three colors of the camouflage pattern shall be obtained by subsequent printing using three rollers or screens to match all three colors. Resin bonded pigments shall not be

37、used (see 6.5). 3.5.3 Classes 7 and 8, Operation Enduring Freedom Camouflage Pattern (OCP). The cloth shall be dyed to a ground shade either matching or approximating Cream 524 and then shall be overprinted with the camouflage pattern by roller or screen printing. When the ground shade is dyed to ma

38、tch Cream 524, the remaining colors shall be obtained by subsequent printing using six rollers or screens, as appropriate for the Tan 525, Pale Green 526, Olive 527, Dark Green 528, Brown 529 and Dark Brown 530 areas of the pattern. When the ground shade is dyed to approximate Cream 524 all seven co

39、lors of the camouflage pattern shall be obtained by subsequent printing using seven rollers or screens to match all seven colors. Resin bonded pigments shall not be used (see 6.5). 3.5.3.1 Labile sulfur. Dyes and compounds containing elementary sulfur capable of oxidation to sulfuric acid shall not

40、be used. The results shall be free (no discoloration) when tested in accordance with 4.4.3. 3.5.4 Visual shade matching (all Classes). The color and appearance of the camouflage printed cloth shall match the standard sample when tested as specified in 4.4.3. Provided by IHSNot for ResaleNo reproduct

41、ion or networking permitted without license from IHS-,-,-MIL-DTL-44031E 6 3.5.5 Colorfastness (all Classes). The finished cloth shall conform to the colorfastness requirements listed below in Tables I and IA when tested as specified in 4.4.3 and 4.5.1. TABLE I. Colorfastness requirements (Classes 1

42、- 6). Colors Evaluation Laundering (3 cycles) 1/ (minimum) Light (40 hrs Or 170 kJ) 2/ (minimum) Perspiration (acid skitteriness exceeding that shown on the standard sample in any of the printed areas will not be acceptable. When the standard sample is not referenced for pattern execution, a pattern

43、 drawing will be provided and the pattern for Class 1, 2 and 5 shall match that of Drawing 2-1-1516, and for Class 3, 4 and 6 shall match that of Drawing 2-1-2519 (see 2.2.2, 6.2, 6.4 and 6.7). 3.5.7 Spectral reflectance Classes 1, 2 and 5. The spectral reflectance values for each color in the Woodl

44、and Camouflage printed cloth shall conform to the requirements specified in Table II, when tested as specified in 4.4.3. TABLE II. Spectral reflectance requirements, Classes 1, 2 and 5 Reflectance values (percent) - Woodland Camouflage Wavelength Nanometers (nm) Black 357 Light Green 354 Dark Green

45、355 and Brown 356 min. max. min. max. min. max. 600 - 10 8 18 3 9 620 - 10 8 18 3 9 640 - 10 8 18 3 9 660 - 10 8 18 3 12 680 - 10 10 22 3 14 700 - 10 18 33 5 18 720 - 10 22 45 7 20 740 - 10 30 55 12 28 760 - 10 35 65 18 36 780 - 10 40 75 26 44 800 - 10 45 80 34 52 820 - 10 50 86 42 60 840 - 10 55 88

46、 50 68 860 - 10 60 90 56 74 3.5.8 Spectral reflectance Classes 3, 4 and 6. The spectral reflectance values for each color in the Universal Camouflage Pattern printed cloth shall conform to the requirements specified in Table III, when tested as specified in 4.4.3. Provided by IHSNot for ResaleNo rep

47、roduction or networking permitted without license from IHS-,-,-MIL-DTL-44031E 8 TABLE III. Spectral reflectance requirements, Class 3, 4 and 6. Reflectance values (percent) Universal Camouflage Pattern (UCP) Wavelength Nanometers (nm) Desert Sand 500 Urban Gray 501 Foliage Green 502 min. max. min. m

48、ax. min. max. 600 28 40 12 26 8 18 620 30 42 14 26 8 18 640 34 48 14 28 8 20 660 38 56 14 30 10 26 680 44 60 18 34 10 26 700 46 66 24 38 12 28 720 48 68 26 42 16 30 740 48 72 30 46 16 30 760 50 74 32 48 18 32 780 54 76 34 48 18 34 800 54 76 34 50 20 36 820 54 76 36 54 22 38 840 56 78 38 54 24 40 860

49、 56 78 40 56 26 42 3.5.9 Spectral reflectance, Classes 7 and 8. The spectral reflectance values for each color in the Operation Enduring Freedom Camouflage Pattern cloth shall conform to the requirements specified in Table IIIA, when tested as specified in 4.4.3. TABLE IIIA. Spectral reflectance requirements, Class 7 and 8. Reflectance values (percent