DLA MIL-DTL-43976 D-2003 GLOVES AND GLOVE SET CHEMICAL PROTECTIVE《化学防护手套和手套装》.pdf
《DLA MIL-DTL-43976 D-2003 GLOVES AND GLOVE SET CHEMICAL PROTECTIVE《化学防护手套和手套装》.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-DTL-43976 D-2003 GLOVES AND GLOVE SET CHEMICAL PROTECTIVE《化学防护手套和手套装》.pdf(19页珍藏版)》请在麦多课文档分享上搜索。
1、 MIL-DTL-43976D 15 September, 2003 - SUPERSEDING MIL-G-43976C 5 September 1990 DETAILED SPECIFICATION GLOVES AND GLOVE SET, CHEMICAL PROTECTIVE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE * 1.1 Scope. This specification covers chemica
2、l protective rubber gloves and glove set in three different thicknessess. The type I glove set includes a pair of knitted cotton glove inserts. The gloves are special purpose Life Support Clothing and Equipment (LSC&E) items. 1.2 Classification. (see 6.2). Type I - Glove Set (gloves with inserts), 2
3、5-mil rubber Sizes - X-Small, Small, Medium, Large, X-Large Type II - Gloves only, 14 mil rubber Sizes - Small, Medium, Large, X-Large Type III - Gloves only, 7 mil rubber Sizes - Small, Medium, Large, X-Large Beneficial comments (recommendations, additions, deletions, clarifications) and any pertin
4、ent data which may be of use in improving this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP-CNR, 700 Robbins Ave., Philadelphia, PA 19111-5096 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at
5、the end of this document or by letter. AMSC N/A FSC 8415 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43976D 2 2. APPLICABLE DOCUMENTS *2.1 General. The documents listed in this section are specified in sections 3 and 4 of this
6、specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requ
7、irements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless oth
8、erwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS MILITARY MIL-G-3866 - Gloves, Mens Cloth, Cotton, Knitted, Lightweight
9、 MIL-D-12468 - Decontaminating Agent, STB STANDARDS FEDERAL FED-STD-601 - Rubber: Sampling and Testing MILITARY MIL-STD-282 - Filter Units, Protective Clothing, Gas Mask Components and Related Products, Performance Test Methods (Unless otherwise indicated, copies of federal and military specificatio
10、ns, standards, and handbooks are available from the Defense Automated Printing Service, Bldg. 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) *2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a
11、part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS U.S. ARMY SOLDIER BIOLOGICAL AND CHEMICAL COMMAND 8-1-307 - Forms for Gloves, Chemical Protective (Copies of drawings are available from the U. S. Army Biologica
12、l and Chemical Command, ATTN: SSCNC-EMSS, NATICK, MA 01760-5017.) FIELD MANUAL Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43976D 3 U.S. ARMY CHEMICAL SCHOOL FM 3-5, NBC DECONTAMINATION (Copies of field manuals are available from the U. S
13、. Army Chemical School, ATTN: ATZN-CM-NF, Fort, McClellan, Anniston, AL 36205-5020) 2.3 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed i
14、n the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM-D-297 - Rubber Product Chemical Analysis ASTM-
15、D-412 - Rubber Properties in Tension ASTM-D-573 - Rubber-Deterioration in an Air Oven ASTM-D-1053 - Stiffness, Torsional, Low-Temperature (Applications for copies of referenced documents should be addressed to the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken,
16、PA 19426-2959.) AMERICAN SOCIETY FOR QUALITY CONTROL ANSI/ASQC Z1.4 Sampling Procedures And Tables For Inspection By Attributes (Applications for copies should be addressed to ANSI/ASQC, American Society for Quality Control, 611 East Wisconsin Ave., Milwaukee, WI 53202.) 2.4 Order of precedence. In
17、the event of a conflict between the text of this specification and the references cited herein, the text of this specification takes precedence. Nothing in this specification, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS *3.1 Firs
18、t article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 4.2 and 6.2). *3.2 Samples. Samples, when furnished, are solely for guidance and information to the contractor (see 6.4). Variations from this specification may appear in the sample, in which case the s
19、pecification shall govern. *3.3 Material. *3.3.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requir
20、ements, and promotes economically advantageous life cycle costs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43976D 4 *3.3.2 Rubber compound. The gloves shall be made of butyl rubber, pigmented black, suitably compounded and vulcanized to
21、 meet the requirements of Table I when tested as specified in 4.4.5. TABLE I Vulcanized rubber glove requirements - Characteristic Type I Type II Type III - Thickness, inch 0.025 1/ 0.014 2/ 0.007 3/ Tensile strength, p.s.i., (min): Original 1100 1100 1100 After aging 1000 1000 1000 After decontamin
22、ation solution immersion 800 800 800 Tensile stress original at 200% Elongation, p.s.i 200 4/ 200 4/ 200 4/ Ultimate elongation, % (min) Original 400 400 400 After aging 350 350 350 After decontamination 300 300 300 Low temperature stiffening 5/ 5/ 6/ Deformation due to decontamination Solution, (ma
23、x): After immersion, wet, % increase in thickness 10.0 10.0 10.0 After immersion, wet, % increase in length 7.5 7.5 7.5 After immersion and aeration, % increase in thickness 5.0 5.0 5.0 After immersion and aeration, % increase in length 5.0 5.0 5.0 Porosity Pass 7/ Pass 7/ Pass 7/ Mustard resistance
24、 (break time in minutes), minimum 360 240 75 GB resistance (break time in minutes), minimum 450 450 360 - 1/ The thickness tolerance of all areas of the gloves, except the crotch areas, shall be 0.005, +0.007 inch. The thickness tolerance of the crotch areas shall be 0.007 + 0.009 inch. The maximum
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILDTL43976D2003GLOVESANDGLOVESETCHEMICALPROTECTIVE 化学 防护 手套 套装 PDF

链接地址:http://www.mydoc123.com/p-690789.html