DLA MIL-DTL-43719 2 B-2009 MARKING MATERIALS AND MARKERS ADHESIVE ELASTOMERIC PIGMENTED LEGENDS.pdf

《DLA MIL-DTL-43719 2 B-2009 MARKING MATERIALS AND MARKERS ADHESIVE ELASTOMERIC PIGMENTED LEGENDS.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-43719 2 B-2009 MARKING MATERIALS AND MARKERS ADHESIVE ELASTOMERIC PIGMENTED LEGENDS.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 7690 INCH-POUND MIL-DTL-43719/2B 6 APRIL 2009 SUPERSEDING MIL-M-43719/2A 13 July 1972 DETAIL SPECIFICATION SHEET MARKING MATERIALS AND MARKERS, ADHESIVE, ELASTOMERIC, PIGMENTED; LEGENDS This specification is approved for use by all Departments and Agencies of the Department of Defense.

2、The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-43719. REQUIREMENTS: Classification. Legend markers shall be of the following style, as specified: Style A - Cutout legend Style B - Printed legend Materials. Legend markers shall be mad

3、e from marking material, liner, and when specified (see 6.2 of general specification), translucent transfer sheet, all conforming to requirements specified in MIL-DTL-43719. Ink(s) for type II markers shall be compatible with the specified marking material. When tested as in the general specificatio

4、n, the printed marking materials shall meet the performance requirements of the general specification. Lettering. Unless otherwise specified in the contract or order, the heights, dimensions, and configurations of the letters and numerals of the legend, and the spacing between letters, shall be as s

5、pecified for Series C Alphabet per Standard Highway Signs (SHS) 2004 Edition. One inch high letters and numerals shall be half-scale of the 2 inch size therein. Space between words. The space between words, measured horizontally from the extreme right edge of the letter preceding the space to the ex

6、treme left edge of the letter following, shall generally be 75% of the letter height. This space may be reduced or increased where needed to obtain a more symmetrical appearance for easy and natural reading, for example, where an L is followed by a J, or where an H is followed by an I. Construction.

7、 Style A. Cutout legend markers shall consist of a legend of letters or numerals or a combination thereof, cut from marking material, each letter and numeral mounted in line on a single, rectangular liner, and covered with a single, rectangular, translucent transfer sheet. All edges shall be cut smo

8、oth. The liner shall not be cut completely through at the outline of letters and numerals, nor shall it be cut so deep as to interfere with its ready removal from the marker or to result in distortion of the marker when removal is attempted. Style B. Printed legend markers shall consist of a legend,

9、 instructions, notice or other written material printed on a sheet of marking material of specified dimensions, type, class, and color (see 6.2 of general specification). The written material shall have the content, arrangement, letter, size(s), and color as specified in the contract or order. After

10、 printing, the entire marker shall be given a clear overcoating to produce a final finish of uniform appearance and of the specified gloss (see ordering data). When specified (see 6.2 of the general specification), the marker shall be covered on the face side with translucent transfer sheet. Provide

11、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43719/2B 2Dimensions. Shall be as follows: (a) Letter height As specified in contract or order. (b) Liner height (1) Letter height up to 2 inches plus 5/16 inch. (2) Letter height over 2 inches plus 9/

12、16 inch. (c) Transfer sheet height Liner height minus 1/16 inch. (d) Width of left and right margin (1) 1/8 inch for legends up to 2 inches high. (2) 1/4 inch for legends over 2 inches high. (e) Top and bottom margins (letters on liner) Equal. (f) Alignment of liner and transfer sheet Edges of liner

13、 flush with edges of transfer sheet at top and sides. (Liner to protrude 1/16 inch at bottom edge.) Alternate. Legend markers which can not be adequately described through above requirements shall be constructed in accordance with drawing(s) to be furnished by the contracting officer. List of legend

14、s. Legends covered by this specification include, but are not limited to, the following: U S ARMY U S COAST GUARD U S NAVY U S MARINE CORPS U S AIR FORCE UNITED STATES ARMY AMBULANCE DEPARTMENT OF DEFENSE FLAMMABLE ARMY NATIONAL GUARD FOR OFFICIAL USE ONLY AIR NATIONAL GUARD MAX SPEED DEFENSE LOGIST

15、IC AGENCY NO RIDERS POLICE NO SMOKING ARMED FORCES POLICE EMERGENCY DOOR NO SMOKING WITHIN 50 FEET Ordering data. Procurement documents should specify the following in addition to the ordering data listed in the general specification: (a) Construction style. (b) Legend content (see list of legends).

16、 (c) Size (height of lettering) (see lettering). (d) Heights, dimensions, and configurations if other than Series C Alphabet. (e) Drawing number, if required (see construction) (alternate). (f) Degree of gross after overcoating. Changes from previous issue. Marginal notations are not used in this re

17、vision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43719/2B 3Custodians: Preparing activity: Army GL DLA IS Navy SA Air Force 99 (Project 7690-2009-0

18、03) Review activities: Army AT, AV, CR, MD Navy MC Air Force 84 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-