DLA MIL-DTL-3922 53 E-2010 FLANGES WAVEGUIDE (COVER) (SQUARE 4 HOLE) (CIRCULAR BACK).pdf

《DLA MIL-DTL-3922 53 E-2010 FLANGES WAVEGUIDE (COVER) (SQUARE 4 HOLE) (CIRCULAR BACK).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-3922 53 E-2010 FLANGES WAVEGUIDE (COVER) (SQUARE 4 HOLE) (CIRCULAR BACK).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5985 MIL-DTL-3922/53E 8 January 2010 SUPERSEDING MIL-DTL-3922/53D 6 March 2000 DETAIL SPECIFICATION SHEET FLANGES, WAVEGUIDE (COVER) (SQUARE, 4 HOLE) (CIRCULAR BACK) This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The requirements f

2、or acquiring the flanges described herein shall consist of this document and the latest issue of MIL-DTL-3922. NOTES: 1. Dimensions are in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general information only and are based upon 1.00 inch = 25.4 mm. 3. Metric equivalents are i

3、n parentheses. 4. These surfaces need to be parallel after drilling and reaming for Part or Identifying Numbers (PINs) M3922/53-005 and M3922/53-006 to facilitate the use of quick disconnect couplings. 5. Roughness of mating surfaces shall not exceed 63 microinches in accordance with ASME-B46.1, exc

4、ept that flaws shall be included in the roughness height measurement. FIGURE 1. Flange configuration. INCH-POUND J M C B TOL R- A -C A .015 MC A .015 MBD DE E C A B TOT T F DIA. 4 HOLESB .015 TOTAL CM RAD.MAX.AAC A TOL R A .015 TOTAL- B -634TYPSIDESCBBCHAMFER4 PLAKDIA. GDIA.Z RADMAX.- C -.001MARKING

5、SECTION A-A HSEENOTE 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/53E 2 TABLE I. Dash numbers and dimensions. PIN M3922/53- Dimensions 1/ 2/ 3/ Dash Used with Dash Used with no. 4/ Waveguide M85/1- Mating flange M3922/59- no. 5/ Wave

6、guide M85/1- Mating flange M3922/59-A B C .015 (0.38) D BSC E BSC 001 079 075 006 003 077 078 178 008 1.005 +.003 (25.53) (0.08)-.000 .505 +.003 (12.83) (0.08)-.000 1.625 (41.28) .640 (16.26) .610 (15.49) 002 073 069 007 004 071 072 177 009 1.255 +.003 (31.88) (0.08)-.000 .630 +.003 (16.00) (0.08)-.

7、000 1.875 (47.63) .737 (18.72) .676 (17.17) 005 089 093 087 001 006 090 091 180 002 .706 +.002 (17.93) (0.05)-.000 .395 +.002 (10.03) (0.05)-.000 1.313 (33.35) .478 (12.14) .497 (12.62) 007 081 085 010 008 083 084 179 011 .854 +.002 (21.69) (0.05)-.000 .479 +.002 (12.17) (0.05)-.000 1.500 (38.10) .5

8、61 (14.25) .520 (13.21) 009 079 075 006 010 077 078 178 008 1.005 +.003 (25.53) (0.08)-.000 .505 +.003 (12.83) (0.08)-.000 1.625 (41.28) .640 (16.26) .610 (15.49) 011 089 093 001 012 090 091 180 002 .706 +.002 (17.93) (0.05)-.000 .395 +.002 (10.03) (0.05)-.000 1.313 (33.35) .478 (12.14) .497 (12.62)

9、 013 081 085 010 014 083 084 179 011 .854 +.002 (21.69) (0.05)-.000 .479 +.002 (12.17) (0.05)-.000 1.500 (38.10) .561 (14.25) .520 (13.21) 015 075 079 013 016 077 078 178 014 1.005 +.003 (25.53) (0.08)-.000 .505 +.003 (12.83) (0.08)-.000 1.625 (41.28) .640 (16.26) .610 (15.49) 017 087 089 093 - 018

10、090 091 180 - .706 +.002 (17.93) (0.05)-.000 .395 +.002 (10.03) (0.05)-.000 1.313 (33.35) .478 (12.14) .497 (12.62) See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/53E 3 TABLE I. Dash numbers and dimensions

11、 - Continued. Dimensions 1/ 2/ 3/ Dash no. 4/ Dash no. 5/ F G Dia. .015 (0.38) H J .015 (0.38) K Dia. .015 (0.38) M Max R R T Z Max R 001 003 .169 +.003 (4.29) (0.08) -.000 1.422 (36.12) .160 .010 (6.22) (0.25) .438 (11.12) 1.062 (26.97) .046 (1.17) .0015 (0.04) .002 (0.05) .062 (1.57) 002 004 .169

12、+.003 (4.29) (0.08) -.000 1.531 (38.89) .250 .015 (6.35) (0.38) .438 (11.12) 1.312 (33.32) .031 (0.79) .0015 (0.04) “ .062 (1.57) 005 006 .144 +.003 (3.66) (0.08) -.000 1.000 (25.40) .125 .015 (3.18) (0.38) .313 (7.95) - .010 (0.25) .001 (0.02) “ .031 (0.79) 007 008 .144 +.003 (3.66) (0.08) -.000 1.

13、141 (28.98) .203 .015 (7.89) (0.38) .391 (9.93) - .010 (0.25) .001 (0.02) “ .062 (1.57) 009 010 .169 +.003 (4.29) (0.08) -.000 1.422 (36.19) .250 .015 (6.35) (0.38) .438 (11.12) 1.062 (26.97) .046 (1.17) .0015 (0.04) “ .062 (1.57) 011 012 .144 +.003 (3.66) (0.08) -.000 1.000 (25.40) “ .313 (7.95) -

14、.010 (0.25) .001 (0.02) “ .031 (0.79) 013 014 .144 +.003 (3.66) (0.08) -.000 1.141 (28.98) “ .391 (9.93) - .010 (0.25) .001 (0.02) “ .062 (1.57) 015 016 .164-32 UNC-2B 1.422 (36.19) .160 .010 (6.22) (0.25) .438 (11.12) 1.062 (26.97) .046 (1.17) .0015 (0.04) .004 (0.10) .062 (1.57) 017 018 .138-32 UN

15、C-2B 1.000 (25.40) .125 .015 (3.18) (0.38) .313 (7.95) - .010 (0.25) .001 (0.02) .004 (0.10) .031 (0.79) 1/ Dimensions are in inches. 2/ Metric equivalents (to the nearest 0.01 mm) are given for general information only and are based upon 1.00 inch = 25.4 mm. 3/ Metric equivalents are in parentheses

16、. 4/ Material shall be copper alloy. 5/ Material shall be aluminum alloy. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/53E 4 REQUIREMENTS: Dimensions and configuration: See figure 1 and table I. Material: Metallic alloy as specified i

17、n table I. Marking: See figure 1. PIN: M3922/53- (and dash number from table I). TABLE II. Cross-reference and engineering information. PIN M3922/53- AN nomenclature Frequency range (GHz) 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 UG-39/U UG-51/U UG-135/U UG-138/U UG-419

18、/U UG-1665/U - - - - - - - - - - - - 8.20 - 12.40 7.05 - 10.00 8.20 - 12.40 7.05 - 10.00 12.40 - 18.00 12.40 - 18.00 10.00 - 15.00 10.00 - 15.00 8.20 - 12.40 8.20 - 12.40 12.40 - 18.00 12.40 - 18.00 10.00 - 15.00 10.00 - 15.00 8.20 - 12.40 8.20 - 12.40 12.40 - 18.00 12.40 - 18.00 Referenced document

19、s. In addition to MIL-DTL-3922, this specification sheet references the following documents: ASME-B46.1 Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing activity: Army - CR DLA - CC Navy -

20、EC Air Force - 85 (Project 5985-2009-035) DLA - CC Review activities: Army - AR, AV, MI Navy - AS, MC, OS, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-